DTC B1805/52 Short in Front Passenger Side Squib Circuit |
DTC B1806/52 Open in Front Passenger Side Squib Circuit |
DTC B1807/52 Short to GND in Front Passenger Side Squib Circuit |
DTC B1808/52 Short to B+ in Front Passenger Side Squib Circuit |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1805/52 | One of the following conditions is met:
|
|
| B1806/52 | One of the following conditions is met:
|
|
| B1807/52 | One of the following conditions is met:
|
|
| B1808/52 | One of the following conditions is met:
|
|

| 1.CHECK INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (FRONT PASSENGER SIDE SQUIB) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the instrument panel passenger airbag.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (orange connector).
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Front Passenger Side Squib |
| *2 | Center Airbag Sensor |
| *3 | Connector E |
| *4 | SST |
| *a | Front view of wire harness connector (to Front Passenger Side Squib) |
| *b | Color: Orange |
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector E.
![]() |
Check that the No. 2 instrument panel wire connectors (on the instrument panel passenger airbag side) are not damaged.
| *1 | Front Passenger Side Squib |
| *2 | Center Airbag Sensor |
|
| ||||
| OK | |
| 3.CHECK FRONT PASSENGER SIDE SQUIB CIRCUIT |
![]() |
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F1-2 (P+) - Body ground | Ignition switch ON | Below 1 V |
| F1-1 (P-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F1-2 (P+) - F1-1 (P-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F1-2 (P+) - F1-1 (P-) | Always | 1 MΩ or higher |
| F1-2 (P+) - Body ground | Always | 1 MΩ or higher |
| F1-1 (P-) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Passenger Side Squib |
| *2 | Center Airbag Sensor |
| *3 | Connector E |
| *a | Front view of wire harness connector (to Front Passenger Side Squib) |
| *b | Color: Orange |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR |
![]() |
Connect the connectors to the instrument panel passenger airbag and center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Front Passenger Side Squib |
| *2 | Center Airbag Sensor |
|
| ||||
| OK | ||
| ||
| 5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE) |
![]() |
Restore the released activation prevention mechanism of connector B to its original condition.
Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| Fz1-1 (P+) - Body ground | Ignition switch ON | Below 1 V |
| Fz1-2 (P-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Fz1-1 (P+) - Fz1-2 (P-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Fz1-1 (P+) - Fz1-2 (P-) | Always | 1 MΩ or higher |
| Fz1-1 (P+) - Body ground | Always | 1 MΩ or higher |
| Fz1-2 (P-) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Passenger Side Squib |
| *2 | No. 2 Instrument Panel Wire |
| *3 | Instrument Panel Wire |
| *4 | Center Airbag Sensor |
| *5 | Connector C |
| *a | Front view of wire harness connector (to No. 2 Instrument Panel Wire) |
|
| ||||
| OK | ||
| ||