Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0300    Random / Multiple Cylinder Misfire Detected

DTC    P0301    Cylinder 1 Misfire Detected

DTC    P0302    Cylinder 2 Misfire Detected

DTC    P0303    Cylinder 3 Misfire Detected

DTC    P0304    Cylinder 4 Misfire Detected

DTC    P0305    Cylinder 5 Misfire Detected

DTC    P0306    Cylinder 6 Misfire Detected

for Preparation Click here


DESCRIPTION

When the engine misfires, high concentrations of hydrocarbons enter the exhaust gas. High hydrocarbon concentration levels can cause an increase in exhaust emission levels. Extremely high concentrations of hydrocarbons can also cause increases in the three-way catalytic converter temperature, which may cause damage to the three-way catalytic converter. To prevent this increase in emissions and to limit the possibility of thermal damage, the ECM monitors the misfire rate. When the temperature of the three-way catalytic converter reaches the point of thermal degradation, the ECM blinks the MIL. To monitor misfires, the ECM uses both the VVT sensor and crankshaft position sensor. The VVT sensor is used to identify any misfiring cylinders and the crankshaft position sensor is used to measure variations in the crankshaft rotation speed. Misfires are counted when the crankshaft rotation speed variations exceed predetermined thresholds. If the misfire count exceeds the threshold levels, the ECM illuminates the MIL and stores a DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0300
Simultaneous misfiring of several cylinders occurs and one of the following conditions is detected (2 trip detection logic):
  1. High temperature misfire occurs in the three-way catalytic converter (MIL blinks).
  2. Emission deterioration misfire occurs (MIL illuminates when detect immediately).
  1. Open or short in engine wire harness
  2. Connector connection
  3. Vacuum hose connections
  4. Ignition system
  5. Fuel injector
  6. Fuel pressure
  7. Mass air flow meter
  8. Engine coolant temperature sensor
  9. Compression pressure
  10. Valve clearance
  11. Valve timing
  12. PCV valve and hose
  13. PCV hose connections
  14. Air induction system
  15. ECM
P0301
P0302
P0303
P0304
P0305
P0306
Misfiring of a specific cylinder occurs and one of the following conditions is detected (2 trip detection logic):
  1. High temperature misfire occurs in the three-way catalytic converter (MIL blinks).
  2. Emission deterioration misfire occurs (MIL illuminates when detect immediately).
When multiple DTCs for misfiring cylinders are stored, but DTC P0300 is not stored, it indicates that misfires have been detected in different cylinders at different times. DTC P0300 is only stored when several misfiring cylinders are detected at the same time.

MONITOR DESCRIPTION


A107734E06


Text in Illustration 
*1
VVT Sensor for Intake Side
*2
VVT Sensor for Exhaust Side
*3
Crankshaft Position Sensor (34 teeth (36 - 2))
*4
ECM
The ECM illuminates the MIL and stores a DTC when either one of the following conditions, which could cause emission deterioration, is detected (2 trip detection logic).
  1. Within the first 1000 crankshaft revolutions after the engine starts, an excessive number of misfires (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs once.
  2. An excessive number of misfires (approximately 20 to 50 misfires per 1000 crankshaft revolutions) occurs a total of 4 times.
The ECM flashes the MIL (immediate detection logic) and stores a DTC (2 trip detection logic) when either one of the following conditions, which could cause damage to the three-way catalytic converter, is detected.
  1. At a high engine speed, catalyst-damaging misfire, which is monitored every 200 crankshaft revolutions, occurs once.
  2. At a normal engine speed, catalyst-damaging misfire, which is monitored every 200 crankshaft revolutions, occurs 3 times.

HINT:
If catalyst-damaging misfire occurs, the ECM informs the driver by flashing the MIL.


MONITOR STRATEGY


Related DTCs
P0300: Multiple cylinder misfire
P0301: Cylinder 1 misfire
P0302: Cylinder 2 misfire
P0303: Cylinder 3 misfire
P0304: Cylinder 4 misfire
P0305: Cylinder 5 misfire
P0306: Cylinder 6 misfire
Required Sensors/Components (Main)
Fuel injector, Ignition coil and spark plug
Required Sensors/Components (Related)
Crankshaft position, VVT position
Engine coolant temperature and intake air temperature sensors and mass air flow meter
Frequency of Operation
Continuous
Duration
1000 crankshaft revolutions (soon after engine is started: 1 time, other 4 times) (Emission-related misfire)
200 crankshaft revolutions (1 to 3 times) (Catalyst-damaging misfire)
MIL Operation
2 driving cycles: (MIL illuminates when misfire detected)
MIL flashes immediately: When catalyst-damaging misfire occurs
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Misfire 
Monitor runs whenever following DTCs not present
P0016, P0018 (VVT System - Misalignment)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0102, P0103 (Mass air flow meter)
P0112, P0113 (Intake air temperature sensor)
P0115, P0117, P0118 (Engine coolant temperature sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0125 (Insufficient engine coolant temperature for Closed Loop)
P0327, P0328, P0332, P0333 (Knock sensor)
P0335 (Crankshaft position sensor)
P0340 (Camshaft position sensor)
P0351 - P0356 (Igniter)
P0500 (VSS)
P0705 (Shift lever position switch)
Battery voltage
8 V or higher
VVT system
Not operated by scan tool
Engine speed
400 to 5900 rpm
Either of condition (a) or (b) met
-
(a) Engine coolant temperature at engine start
Higher than -7°C (19°F)
(b) Engine coolant temperature
Higher than 20°C (68°F)
Fuel cut
OFF

Monitor Period of Emissions-related Misfire 
First 1000 revolutions after engine start, or Check Mode
Crankshaft 1000 revolutions
Except above
Crankshaft 1000 revolutions x 4

Monitor Period of Catalyst-damaging Misfire (MIL Blinks) 
Conditions 1, 2 and 3 met
Crankshaft 200 revolutions x 3
1. Driving cycles
1st
2. Check mode
OFF
3. Engine speed
Less than 1900 rpm
Except above
Crankshaft 200 revolutions

TYPICAL MALFUNCTION THRESHOLDS


Monitor Period of Emissions-related Misfire 
Misfire rate
1.5% or more

Monitor Period of Catalyst-damaging Misfire (MIL Blinks) 
Number of misfires per 200 revolutions
77 or more (varies with intake air amount and engine speed)
Paired cylinder misfire (MIL blinks immediately)
Detected

CONFIRMATION DRIVING PATTERN

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Record the DTCs and freeze frame data.
  5. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  6. Using the Techstream, switch the ECM from normal mode to check mode (Click here).
  7. Read the misfire counts of each cylinder (cylinder No. 1 to No. 6) with the engine idling. If any misfire count is displayed, skip the following confirmation driving pattern.
  8. Drive the vehicle several times with the conditions, such as engine speed and engine load, as shown in Misfire RPM and Misfire Load in the Data List.

    HINT:
    In order to store misfire DTCs, it is necessary to operate the vehicle for the period of time shown in the table below, using the Misfire RPM and Misfire Load in the Data List.

    Engine Speed
    Duration
    Idling
    8.0 minutes or more
    1000
    4.5 minutes or more
    2000
    2.5 minutes or more
    3000
    1.5 minutes or more

  9. Check whether misfires have occurred by checking DTCs and freeze frame data.

    HINT:
    Do not turn the ignition switch off until the stored DTCs and freeze frame data have been recorded. When the ECM returns to normal mode (default), the stored DTCs, freeze frame data and other data will be cleared.

  10. Record the DTCs, freeze frame data and misfire counts.
  11. Turn the ignition switch off and wait for at least 5 seconds.
  12. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

WIRING DIAGRAM


A246545E01


A227110E01


A227116E01

Refer to DTC P0102 .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. If any DTCs other than misfire DTCs are output, troubleshoot those DTCs first.
  2. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
  3. If the misfire does not recur when the vehicle is brought to the workshop, reproduce the conditions stored in the ECM as freeze frame data.
  4. If the misfire still cannot be reproduced even though the conditions stored in the ECM as freeze frame data have been reproduced, one of the following factors can be considered to be a possible cause of the problem:
    1. There was an insufficient amount of fuel in the tank.
    2. Improper fuel was used.
    3. The spark plugs have been contaminated.
  5. After finishing repairs, check the misfire counts of the cylinders (Cylinder #1 Misfire Count to Cylinder #6 Misfire Count).
  6. Be sure to confirm that no misfiring cylinder DTCs are stored again by conducting the confirmation driving pattern after finishing repairs.
  7. For 6 and 8 cylinder engines, the ECM intentionally does not store the specific misfiring cylinder DTCs at high engine speeds. If misfires occur only at high engine speeds, only DTC P0300 is stored.
    In the event of DTC P0300 being output, perform the following operations:
    1. Clear the DTCs (Click here).
    2. Start the engine and conduct the confirmation driving pattern.
    3. Read the misfiring rates of each cylinder or the DTCs using the Techstream.
    4. Repair the cylinders that have a high misfiring rate or are indicated by the DTCs.
    5. After finishing repairs, conduct the confirmation driving pattern again in order to verify that DTC P0300 is not stored.
  8. When one of Short FT #1, Long FT #1, Short FT #2 or Long FT #2 in the freeze frame data is outside the range of +/-20%, the air-fuel ratio may be Rich (-20% or less) or Lean (+20% or more).
  9. When Coolant Temp in the freeze frame data is below 75°C (167°F), the misfire may have occurred only while warming up the engine.
  10. An extremely imbalanced drive wheel which causes body vibration may cause misfire DTCs to be stored.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO MISFIRE CODES)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read DTCs.

    HINT:
    Write down the DTCs.


    Result 
    Display (DTC Output)
    Proceed to
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306
    A
    P0300, P0301, P0302, P0303, P0304, P0305 and/or P0306 and other DTCs
    B

HINT:
If any DTCs other than P0300, P0301, P0302, P0303, P0304, P0305 and P0306 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.CHECK PCV HOSE CONNECTIONS
  1. Check the PCV hose connections.

OK:
PCV hose is correctly connected and is not damaged.



NG
REPAIR OR REPLACE PCV HOSE (Click here)
OK


3.READ VALUE USING TECHSTREAM (MISFIRE RPM AND MISFIRE LOAD)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Misfire RPM and Misfire Load.

  1. Read and note the Misfire RPM and Misfire Load values.

    HINT:
    The Misfire RPM and Misfire Load values indicate the vehicle conditions under which the misfire occurred.


NEXT


4.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Catalyst OT MF F/C.

  1. Read the value displayed on the Techstream.
    Result  
    Data List
    Display Item
    Proceed to
    Catalyst OT MF F/C
    Avail
    A
    Not Avl
    B



B
Go to step 6
A


5.PERFORM ACTIVE TEST USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Prohibit the Catalyst OT Misfire prevent F/C.

  1. Perform the Active Test.

    NOTICE:
    When performing the Active Test, make sure the vehicle is stopped and the engine is either idling or being revved at 3000 rpm or less.


NEXT


6.READ VALUE USING TECHSTREAM (MISFIRE COUNT)
  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Cylinder #1 Misfire Count, #2, #3, #4, #5 and #6.

  1. Read the values for Cylinder #1 Misfire Count to Cylinder #6 Misfire Count displayed on the Techstream. If no misfire counts occur in any cylinders, perform the following procedure:

    1. Start the engine and let it idle.
    2. Move the shift lever to D.
    3. Check Cylinder #1 Misfire Count to Cylinder #6 Misfire Count.
    4. If misfire counts are still not displayed, perform the steps below.

  1. Drive the vehicle while satisfying the Misfire RPM and Misfire Load values noted in the "Read Value Using Techstream (Misfire RPM and Misfire Load)" procedure above.

  1. Read Cylinder #1 Misfire Count to Cylinder #6 Misfire Count or the DTCs output on the Techstream.

    Result 
    Misfire Count
    Proceed to
    Most misfires occur in only 1 or 2 cylinders
    A
    3 cylinders or more have equal misfire counts
    B

    HINT:
    1. If it is difficult to reproduce misfires for each cylinder, check the Data List item called Misfire Margin. Try to find vehicle driving conditions that lower the Misfire Margin value. Values above 30% are considered normal.
    2. If the freeze frame data's record of the engine coolant temperature is below 75°C (167°F), the misfire may be detected only when the engine is cold.
    3. If the freeze frame data's record of Engine Run Time is below 120 seconds, the misfire may be detected immediately after the engine is started.



B
Go to step 18
A


7.INSPECT SPARK PLUG
  1. Inspect the spark plug .



NG
REPLACE SPARK PLUG (Click here)
OK


8.CHECK FOR SPARKS AND IGNITION
  1. Perform a spark test .

    CAUTION:
    Always disconnect all the injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    OK:
    Spark jumps across electrode gap.



NG
Go to step 34
OK


9.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


10.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR OF MISFIRING CYLINDER)


    A208644E06
  1. Disconnect the fuel injector assembly connector (of the misfiring cylinder).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    B1-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 2
    B2-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 3
    B3-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 4
    B4-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 5
    B5-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 6
    B6-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

  1. Reconnect the fuel injector assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (IG2) - FUEL INJECTOR)
OK


11.CHECK HARNESS AND CONNECTOR (ECM - FUEL INJECTOR OF MISFIRING CYLINDER)
  1. Disconnect the fuel injector assembly connector (of the misfiring cylinder).

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    B1-2 - Body ground
    Always
    10 kΩ or higher
    B1-2 - B39-6 (#10)
    Always
    Below 1 Ω
    No. 2
    B2-2 - Body ground
    Always
    10 kΩ or higher
    B2-2 - B39-1 (#20)
    Always
    Below 1 Ω
    No. 3
    B3-2 - Body ground
    Always
    10 kΩ or higher
    B3-2 - B39-7 (#30)
    Always
    Below 1 Ω
    No. 4
    B4-2 - Body ground
    Always
    10 kΩ or higher
    B4-2 - B39-2 (#40)
    Always
    Below 1 Ω
    No. 5
    B5-2 - Body ground
    Always
    10 kΩ or higher
    B5-2 - B39-8 (#50)
    Always
    Below 1 Ω
    No. 6
    B6-2 - Body ground
    Always
    10 kΩ or higher
    B6-2 - B39-3 (#60)
    Always
    Below 1 Ω

  1. Reconnect the fuel injector assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR - ECM)
OK


12.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the fuel injector resistance .

  1. Check the fuel injector injection (whether fuel volume is high or low, and whether injection pattern is poor) .



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


13.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leakage .

    OK:
    No leakage in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM (Click here)
OK


14.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER
OK


15.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine:
    Same as ambient air temperature.
    With warm engine:
    Between 75°C and 100°C (167°F and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


16.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 13.8 g/sec. and 17.3 g/sec. (shift lever: N; A/C: Off).



NG
Go to step 29
OK


17.CHECK VALVE TIMING


    A103826E11
  1. Remove the cylinder head cover RH and LH.
    Text in Illustration 
    *1
    Timing Mark

  1. Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.

  1. Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), and then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover RH and LH.



OK
Go to step 29

NG
ADJUST VALVE TIMING (Click here)

18.CHECK INTAKE SYSTEM
  1. Check the intake system for vacuum leakage .

    OK:
    No leakage in intake system.



NG
REPAIR OR REPLACE INTAKE SYSTEM (Click here)
OK


19.CHECK FUEL PRESSURE
  1. Check the fuel pressure .



NG
REPAIR OR REPLACE FUEL PUMP, PRESSURE REGULATOR, FUEL PIPE LINE AND FILTER
OK


20.READ VALUE USING TECHSTREAM (COOLANT TEMP)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine / Data List / Coolant Temp.

  1. Read the Data List twice, when the engine is both cold and warmed up.

    Standard:
    With cold engine:
    Same as ambient air temperature.
    With warm engine:
    Between 75°C and 100°C (167°F and 212°F)



NG
REPLACE ENGINE COOLANT TEMPERATURE SENSOR (Click here)
OK


21.READ VALUE USING TECHSTREAM (MAF)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF, Coolant Temp and Engine Speed.

  1. Allow the engine to idle until the Coolant Temp reaches 75°C (167°F) or higher.

  1. Read MAF with the engine speed at 3000 rpm.

    Standard:
    Between 13.8 g/sec. and 17.3 g/sec. (shift lever: N; A/C: Off).



NG
Go to step 29
OK


22.CHECK VALVE TIMING


    A103826E11
  1. Remove the cylinder head cover RH and LH.
    Text in Illustration 
    *1
    Timing Mark

  1. Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.

  1. Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), and then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover RH and LH.



NG
ADJUST VALVE TIMING (Click here)
OK


23.INSPECT SPARK PLUG
  1. Inspect the spark plug .



NG
REPLACE SPARK PLUG (Click here)
OK


24.CHECK FOR SPARKS AND IGNITION
  1. Perform a spark test .

    CAUTION:
    Always disconnect all the injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    OK:
    Spark jumps across electrode gap.



NG
Go to step 34
OK


25.CHECK CYLINDER COMPRESSION PRESSURE
  1. Measure the cylinder compression pressure of the misfiring cylinder .



NG
CHECK ENGINE TO DETERMINE CAUSE OF LOW COMPRESSION
OK


26.CHECK TERMINAL VOLTAGE (POWER SOURCE OF FUEL INJECTOR OF MISFIRING CYLINDER)


    A208644E06
  1. Disconnect the fuel injector assembly connector (of the misfiring cylinder).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    B1-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 2
    B2-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 3
    B3-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 4
    B4-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 5
    B5-1 - Body ground
    Ignition switch ON
    11 to 14 V
    No. 6
    B6-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)

  1. Reconnect the fuel injector assembly connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (NO. 1 INTEGRATION RELAY (IG2) - FUEL INJECTOR)
OK


27.CHECK HARNESS AND CONNECTOR (ECM - FUEL INJECTOR OF MISFIRING CYLINDER)
  1. Disconnect the fuel injector assembly connector (of the misfiring cylinder).

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    B1-2 - Body ground
    Always
    10 kΩ or higher
    B1-2 - B39-6 (#10)
    Always
    Below 1 Ω
    No. 2
    B2-2 - Body ground
    Always
    10 kΩ or higher
    B2-2 - B39-1 (#20)
    Always
    Below 1 Ω
    No. 3
    B3-2 - Body ground
    Always
    10 kΩ or higher
    B3-2 - B39-7 (#30)
    Always
    Below 1 Ω
    No. 4
    B4-2 - Body ground
    Always
    10 kΩ or higher
    B4-2 - B39-2 (#40)
    Always
    Below 1 Ω
    No. 5
    B5-2 - Body ground
    Always
    10 kΩ or higher
    B5-2 - B39-8 (#50)
    Always
    Below 1 Ω
    No. 6
    B6-2 - Body ground
    Always
    10 kΩ or higher
    B6-2 - B39-3 (#60)
    Always
    Below 1 Ω

  1. Reconnect the fuel injector assembly connector.

  1. Reconnect the ECM connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (FUEL INJECTOR - ECM)
OK


28.CHECK FUEL INJECTOR OF MISFIRING CYLINDER
  1. Check the fuel injector resistance .

  1. Check the fuel injector injection (whether fuel volume is high or low, and whether injection pattern is poor) .



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


29.CHECK HARNESS AND CONNECTOR
  1. Check the connection and terminal contact pressure of connectors and wire harnesses between the mass air flow meter and ECM (Click here).

    HINT:
    Repair any problems.


NEXT


30.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Warm up the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, 0304, P0305 or P0306.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    ABNORMAL (P0300, P0301, P0302, P0303, 0304, P0305 or P0306 is output)
    A
    NORMAL (No DTC output)
    B



B
END
A


31.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW - ECM)
  1. Disconnect the mass air flow meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B35-5 (VG) - B37-14 (VG)
    Always
    Below 1 Ω
    B35-4 (E2G) - B37-13 (E2G)
    Always
    Below 1 Ω
    B35-5 (VG) or B37-14 (VG) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the mass air flow meter connector.

  1. Reconnect the ECM connector.



NG
REPLACE HARNESS OR CONNECTOR (MASS AIR FLOW - ECM)
OK


32.REPLACE MASS AIR FLOW METER
  1. Replace the mass air flow meter (Click here).

    HINT:
    If the results of the inspections performed in steps 16 and 21 indicated no problem, proceed to the next step without replacing the mass air flow meter.


NEXT


33.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Warm up the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

  1. Input the DTC: P0300, P0301, P0302, P0303, 0304, P0305 or P0306.

  1. Check the DTC judgment result.
    Result 
    Result
    Proceed to
    NORMAL
    (No DTC output)
    A
    ABNORMAL
    (P0300, P0301, P0302, P0303, 0304, P0305 or P0306 is output)
    B



B
REPLACE ECM (Click here)
A

END 

34.REPLACE SPARK PLUG WITH NORMAL ONE AND CHECK SPARK OF MISFIRING CYLINDER
  1. Replace the installed spark plug with a spark plug that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all fuel injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connectors.

    2. Disconnect the fuel injector connectors.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
Go to step 35
OK

REPLACE SPARK PLUG (Click here)  

35.REPLACE IGNITION COIL WITH NORMAL ONE AND CHECK SPARK OF MISFIRING CYLINDER
  1. Replace the ignition coil with an ignition coil that functions normally.

  1. Perform a spark test.

    CAUTION:
    Always disconnect all fuel injector connectors.

    NOTICE:
    Do not crank the engine for more than 2 seconds.

    1. Install the spark plug to the ignition coil and connect the ignition coil connector.

    2. Disconnect the fuel injector connectors.

    3. Ground the spark plug.

    4. Check if sparks occur while the engine is being cranked.

      OK:
      Sparks jump across electrode gap.



NG
REPLACE ECM (Click here)
OK

REPLACE IGNITION COIL (Click here)