POWER WINDOW CONTROL SYSTEM > Rear Power Window RH does not Operate with Rear Power Window Switch RH |

| 1.CHECK FOR DTC (B2312) |
Check if DTC B2312 is output (Click here).
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (REAR POWER WINDOW REGULATOR SWITCH) |
Use the Data List to check if the rear power window regulator motor is functioning properly (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Door P/W Up SW | Rear power window RH manual up signal / ON or OFF | ON: Rear power window RH manual up switch operated OFF: Rear power window RH switch not operated | - |
| RR Door P/W Down SW | Rear power window RH manual down signal / ON or OFF | ON: Rear power window RH manual down switch operated OFF: Rear power window RH switch not operated | - |
|
| ||||
| OK | ||
| ||
| 3.PERFORM ACTIVE TEST USING TECHSTREAM (POWER WINDOW) |
Select the Active Test, use the Techstream to generate a control command, and then check that power window regulator motor operates (Click here).
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Power Window | Rear RH side power window | OFF/UP/DOWN | - |
|
| ||||
| OK | ||
| ||
| 4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH |
![]() |
Remove the rear power window regulator switch (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (UP) - 1 (GND) | Manual up operation | Below 1 Ω |
| 7 (DOWN) - 1 (GND) | Manual down operation | Below 1 Ω |
| 6 (UP) - 1 (GND) | Not operated | 10 kΩ or higher |
| 7 (DOWN) - 1 (GND) | Not operated | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - BODY GROUND) |
![]() |
Disconnect the i1 rear power window regulator switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| i1-1 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Rear Power Window Regulator Switch Assembly RH) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH) |
Disconnect the i1 rear power window regulator switch connector.
Disconnect the J2 rear power window regulator motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| i1-6 (UP) - J2-10 (UP) | Always | Below 1 Ω |
| i1-7 (DOWN) - J2-7 (DOWN) | Always | Below 1 Ω |
| i1-6 (UP) - Body ground | Always | 10 kΩ or higher |
| i1-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH - BATTERY AND BODY GROUND) |
![]() |
Disconnect the J2 rear power window regulator motor connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| J2-2 (B) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| J2-1 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Rear Power Window Regulator Motor Assembly RH) |
|
| ||||
| OK | ||
| ||