Home › Vehicle Exterior › WINDOW / GLASS › POWER WINDOW CONTROL SYSTEM

DTC    B2312    Power Window Switch Malfunction

for Preparation Click here


DESCRIPTION

The power window regulator motor is driven by operating the power window regulator switch. The power window regulator motor assembly consists of the motor and ECU.
This DTC is output when the ECU built into the regulator motor and master switch determines that the multiplex network master switch assembly or power window regulator switch assembly is stuck.

HINT:
This DTC may be stored for all the windows.

NOTICE:
  1. When a power window regulator is reinstalled or replaced, the power window control system must be initialized.
  2. After any door glass or a door glass run has been replaced, the jam protection function may operate unexpectedly when the auto up function is used. In such cases, the auto up function can be resumed by repeating the following operation at least 5 times:
    1. Close the power window by fully pulling up the power window switch and holding it in the auto up position.
    2. Open the power window by fully pushing down the power window switch.


Master Switch 
DTC Code
DTC Detection Condition
Trouble Area
B2312
Either condition is met:
  1. The multiplex network master switch is stuck.
  2. The multiplex network master switch is held in the same position for more than 20 sec.
Multiplex network master switch

D-Door Motor 
DTC Code
DTC Detection Condition
Trouble Area
B2312
Either condition is met:
  1. The multiplex network master switch is stuck.
  2. The multiplex network master switch is held in the same position for more than 20 sec.
  1. Multiplex network master switch
  2. Front power window regulator motor LH
  3. Harness or connector

P-Door Motor 
DTC Code
DTC Detection Condition
Trouble Area
B2312
Either condition is met:
  1. The power window regulator switch is stuck.
  2. The power window regulator switch is held in the same position for more than 20 sec.
  1. Power window regulator switch
  2. Front power window regulator motor RH
  3. Harness or connector

RL-Door Motor 
DTC Code
DTC Detection Condition
Trouble Area
B2312
Either condition is met:
  1. The rear power window regulator switch LH is stuck.
  2. The rear power window regulator switch LH is held in the same position for more than 20 sec.
  1. Rear power window regulator switch LH
  2. Rear power window regulator motor LH
  3. Harness or connector

RR-Door Motor 
DTC Code
DTC Detection Condition
Trouble Area
B2312
Either condition is met:
  1. The rear power window regulator switch RH is stuck.
  2. The rear power window regulator switch RH is held in the same position for more than 20 sec.
  1. Rear power window regulator switch RH
  2. Rear power window regulator motor RH
  3. Harness or connector

WIRING DIAGRAM


for Front LH:

B242542E01


for Front RH:

B242543E01


for Rear LH:

B242543E02


for Rear RH:

B242543E03


INSPECTION PROCEDURE

HINT:
Since the power window control system has functions that use LIN communication, first confirm that there is no malfunction in the communication system by inspecting the LIN communication functions in accordance with the "How to Proceed with Troubleshooting" procedures. Then, conduct the following inspection procedure.

1.CHECK FOR DTC
  1. Clear the DTC (Click here).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    No DTCs output
    A
    LIN communication DTCs are output
    B
    DTC B2312 is output
    C



B
GO TO LIN COMMUNICATION SYSTEM (Click here)

C
Go to step 2
A

END (DTC WAS STORED DUE TO SWITCH BEING OPERATED FOR 20 SECONDS OR MORE) 

2.CHECK DTC OUTPUT
  1. Check the parts which the DTCs have been output from.
    Result 
    Result
    Proceed to
    DTC output from multiplex network master switch
    A
    DTC output from front power window regulator motor LH
    B
    DTC output from front power window regulator motor RH
    C
    DTC output from rear power window regulator motor LH
    D
    DTC output from rear power window regulator motor RH
    E



B
Go to step 3

C
Go to step 5

D
Go to step 8

E
Go to step 11
A

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)  

3.READ VALUE USING TECHSTREAM (MULTIPLEX NETWORK MASTER SWITCH)
  1. Use the Data List to check if the power window regulator motor is functioning properly (Click here).

    D-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    D Door P/W Up SW
    Driver side power window manual up signal / ON or OFF
    ON: Driver side power window manual up switch operated
    OFF: Driver side power window switch not operated
    -
    D Door P/W Down SW
    Driver side power window manual down signal / ON or OFF
    ON: Driver side power window manual down switch operated
    OFF: Driver side power window switch not operated
    -

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 4
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)  

4.CHECK HARNESS AND CONNECTOR (MULTIPLEX NETWORK MASTER SWITCH - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
  1. Disconnect the h1 multiplex network master switch connector.

  1. Disconnect the I2 power window regulator motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    h1-20 (UP) - I2-10 (UP)
    Always
    Below 1 Ω
    h1-15 (DOWN) - I2-7 (DOWN)
    Always
    Below 1 Ω
    h1-20 (UP) - Body ground
    Always
    10 kΩ or higher
    h1-15 (DOWN) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)  

5.READ VALUE USING TECHSTREAM (POWER WINDOW REGULATOR SWITCH)
  1. Use the Data List to check if the power window regulator motor is functioning properly (Click here).

    P-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    P Door P/W Auto SW
    Front passenger side power window auto up/down signal / ON or OFF
    ON: Front passenger side power window auto up/down switch operated
    OFF: Front passenger side power window regulator switch not operated
    -
    P Door P/W Up SW
    Front passenger side power window manual up signal / ON or OFF
    ON: Front passenger side power window manual up switch operated
    OFF: Front passenger side power window regulator switch not operated
    -
    P Door P/W Down SW
    Front passenger side power window manual down signal / ON or OFF
    ON: Front passenger side power window manual down switch operated
    OFF: Front passenger side power window regulator switch not operated
    -

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 6
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)  

6.INSPECT POWER WINDOW REGULATOR SWITCH ASSEMBLY


    B215963E13
  1. Remove the power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Manual up operation
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Manual down operation
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    Auto up/down operation
    Below 1 Ω
    6 (UP) - 1 (GND)
    Not operated
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Not operated
    10 kΩ or higher
    8 (AUTO) - 1 (GND)
    Not operated
    10 kΩ or higher



NG
REPLACE POWER WINDOW REGULATOR SWITCH ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (POWER WINDOW REGULATOR SWITCH ASSEMBLY - FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
  1. Disconnect the g1 power window regulator switch connector.

  1. Disconnect the H2 power window regulator motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    g1-6 (UP) - H2-10 (UP)
    Always
    Below 1 Ω
    g1-7 (DOWN) - H2-7 (DOWN)
    Always
    Below 1 Ω
    g1-8 (AUTO) - H2-4 (AUTO)
    Always
    Below 1 Ω
    g1-6 (UP) - Body ground
    Always
    10 kΩ or higher
    g1-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    g1-8 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)  

8.READ VALUE USING TECHSTREAM (REAR POWER WINDOW REGULATOR SWITCH LH)
  1. Use the Data List to check if the power window regulator motor is functioning properly (Click here).

    RL-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RL Door P/W Auto SW
    Rear power window LH auto up/down signal / ON or OFF
    ON: Rear power window LH auto up/down switch operated
    OFF: Rear power window LH switch not operated
    -
    RL Door P/W Up SW
    Rear power window LH manual up signal / ON or OFF
    ON: Rear power window LH manual up switch operated
    OFF: Rear power window LH switch not operated
    -
    RL Door P/W Down SW
    Rear power window LH manual down signal / ON or OFF
    ON: Rear power window LH manual down switch operated
    OFF: Rear power window LH switch not operated
    -

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 9
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)  

9.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH


    B215963E13
  1. Remove the rear power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Manual up operation
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Manual down operation
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    Auto up/down operation
    Below 1 Ω
    6 (UP) - 1 (GND)
    Not operated
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Not operated
    10 kΩ or higher
    8 (AUTO) - 1 (GND)
    Not operated
    10 kΩ or higher



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH)
  1. Disconnect the j1 rear power window regulator switch connector.

  1. Disconnect the K2 rear power window regulator motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    j1-6 (UP) - K2-10 (UP)
    Always
    Below 1 Ω
    j1-7 (DOWN) - K2-7 (DOWN)
    Always
    Below 1 Ω
    j1-8 (AUTO) - K2-4 (AUTO)
    Always
    Below 1 Ω
    j1-6 (UP) - Body ground
    Always
    10 kΩ or higher
    j1-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    j1-8 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)  

11.READ VALUE USING TECHSTREAM (REAR POWER WINDOW REGULATOR SWITCH RH)
  1. Use the Data List to check if the power window regulator motor is functioning properly (Click here).

    RR-Door Motor 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    RR Door P/W Auto SW
    Rear power window RH auto up/down signal / ON or OFF
    ON: Rear power window RH auto up/down switch operated
    OFF: Rear power window RH switch not operated
    -
    RR Door P/W Up SW
    Rear power window RH manual up signal / ON or OFF
    ON: Rear power window RH manual up switch operated
    OFF: Rear power window RH switch not operated
    -
    RR Door P/W Down SW
    Rear power window RH manual down signal / ON or OFF
    ON: Rear power window RH manual down switch operated
    OFF: Rear power window RH switch not operated
    -

    OK:
    On tester screen, each item changes between ON and OFF according to above chart.



NG
Go to step 12
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)  

12.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH


    B215963E13
  1. Remove the rear power window regulator switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    6 (UP) - 1 (GND)
    Manual up operation
    Below 1 Ω
    7 (DOWN) - 1 (GND)
    Manual down operation
    Below 1 Ω
    8 (AUTO) - 1 (GND)
    Auto up/down operation
    Below 1 Ω
    6 (UP) - 1 (GND)
    Not operated
    10 kΩ or higher
    7 (DOWN) - 1 (GND)
    Not operated
    10 kΩ or higher
    8 (AUTO) - 1 (GND)
    Not operated
    10 kΩ or higher



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH)
  1. Disconnect the i1 rear power window regulator switch connector.

  1. Disconnect the J2 rear power window regulator motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    i1-6 (UP) - J2-10 (UP)
    Always
    Below 1 Ω
    i1-7 (DOWN) - J2-7 (DOWN)
    Always
    Below 1 Ω
    i1-8 (AUTO) - J2-4 (AUTO)
    Always
    Below 1 Ω
    i1-6 (UP) - Body ground
    Always
    10 kΩ or higher
    i1-7 (DOWN) - Body ground
    Always
    10 kΩ or higher
    i1-8 (AUTO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)