POWER WINDOW CONTROL SYSTEM > Rear Power Window LH does not Operate with Rear Power Window Switch LH |

| 1.CHECK FOR DTC (B2312) |
Check if DTC B2312 is output (Click here).
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (REAR POWER WINDOW REGULATOR SWITCH) |
Use the Data List to check if the rear power window regulator is functioning properly (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RL Door P/W Up SW | Rear power window LH manual up signal / ON or OFF | ON: Rear power window LH manual up switch operated OFF: Rear power window LH switch not operated | - |
| RL Door P/W Down SW | Rear power window LH manual down signal / ON or OFF | ON: Rear power window LH manual down switch operated OFF: Rear power window LH switch not operated | - |
|
| ||||
| OK | |
| 3.PERFORM ACTIVE TEST USING TECHSTREAM (POWER WINDOW) |
Select the Active Test, use the Techstream to generate a control command, and then check that power window regulator motor operates (Click here).
| Tester Display | Test Part | Control Range | Diagnostic Note |
| Power Window | Rear LH side power window | OFF/UP/DOWN | - |
|
| ||||
| OK | ||
| ||
| 4.INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH |
![]() |
Remove the rear power window regulator switch (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (UP) - 1 (GND) | Manual up operation | Below 1 Ω |
| 7 (DOWN) - 1 (GND) | Manual down operation | Below 1 Ω |
| 6 (UP) - 1 (GND) | Not operated | 10 kΩ or higher |
| 7 (DOWN) - 1 (GND) | Not operated | 10 kΩ or higher |
|
| ||||
| OK | |
| 5.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - BODY GROUND) |
![]() |
Disconnect the j1 rear power window regulator switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| j1-1 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Rear Power Window Regulator Switch Assembly LH) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH - REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH) |
Disconnect the j1 rear power window regulator switch connector.
Disconnect the K2 power window regulator motor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| j1-6 (UP) - K2-10 (UP) | Always | Below 1 Ω |
| j1-7 (DOWN) - K2-7 (DOWN) | Always | Below 1 Ω |
| j1-6 (UP) - Body ground | Always | 10 kΩ or higher |
| j1-7 (DOWN) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 7.CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH - BATTERY AND BODY GROUND) |
![]() |
Disconnect the K2 power window regulator motor connector.
Measure the voltage and resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| K2-2 (B) - Body ground | Always | 11 to 14 V |
| Tester Connection | Condition | Specified Condition |
| K2-1 (GND) - Body ground | Always | Below 1 Ω |
| *a | Front view of wire harness connector (to Rear Power Window Regulator Motor Assembly LH) |
|
| ||||
| OK | ||
| ||