Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Start Function)

DTC    B2285    Steering Lock Position Signal Circuit Malfunction

for Preparation Click here


DESCRIPTION

The power management control ECU and steering lock actuator (steering lock ECU) are connected by a cable and the LIN communication line. This DTC is stored when the steering lock position signal information from the cable and the steering lock position signal information from the LIN communication line are inconsistent.

HINT:
When the power management control ECU is replaced with a new one and the cable is connected to the negative (-) battery terminal, the power source mode is reset to on (IG). When the battery is removed and reinstalled, the power source mode that was selected when the battery was removed is restored.


DTC Code
DTC Detection Condition
Trouble Area
B2285
The steering lock position signal information from the cable and the steering lock position signal information from the LIN communication line are inconsistent.
  1. AM2 fuse
  2. Steering lock actuator assembly (steering lock ECU)
  3. Power management control ECU
  4. LIN communication system
  5. Harness or connector

WIRING DIAGRAM


A207422E04


INSPECTION PROCEDURE

NOTICE:
  1. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
  2. Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  4. After replacing the steering lock actuator assembly (steering lock ECU), perform key ID code registration (Click here).

1.CHECK FOR DTC (LIN COMMUNICATION SYSTEM)
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    LIN communication system DTCs B2287 and B2785 are not output simultaneously.



NG
GO TO DTC B2287 (Click here)
OK


2.CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)


    A207890E08
  1. Disconnect the F80 power management control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F80-2 (AM21) - Body ground
    Always
    9.5 to 14 V
    F80-1 (AM22) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect the F80 power management control ECU connector.



    A207890E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F80-6 (GND) - Body ground
    Always
    Below 1 Ω
    F80-5 (GND2) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU)


    C197722E24
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F68-4 (SLP1) - Body ground
    Steering lock locked
    10 kΩ or higher
    F68-4 (SLP1) - Body ground
    Steering lock released
    Below 1 Ω

    Text in Illustration 
    *a
    Component with harness connected
    (Steering Lock ECU)



NG
REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)
OK


5.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - STEERING LOCK ECU)
  1. Disconnect the F80 power management control ECU connector.

  1. Disconnect the F68 steering lock ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F80-3 (SLP) - F68-4 (SLP1)
    Always
    Below 1 Ω
    F80-3 (SLP) or F68-4 (SLP1) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.READ VALUE USING TECHSTREAM (STEERING UNLOCK SWITCH)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. According to the display on the Techstream, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Steering Unlock Switch
    Steering lock condition / ON or OFF
    ON: Steering lock released (Engine switch on [ACC])
    OFF: Steering lock locked (Engine switch off)
    -

    OK:
    ON (steering lock released) or OFF (steering lock locked) appears on the screen according to the steering lock condition.



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK

REPLACE STEERING LOCK ACTUATOR ASSEMBLY (STEERING LOCK ECU) (Click here)