DTC B1810/53 Short in Driver Side Squib 2nd Step Circuit |
DTC B1811/53 Open in Driver Side Squib 2nd Step Circuit |
DTC B1812/53 Short to GND in Driver Side Squib 2nd Step Circuit |
DTC B1813/53 Short to B+ in Driver Side Squib 2nd Step Circuit |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1810/53 | One of the following conditions is met:
|
|
| B1811/53 | One of the following conditions is met:
|
|
| B1812/53 | One of the following conditions is met:
|
|
| B1813/53 | One of the following conditions is met:
|
|

| 1.CHECK STEERING PAD (DRIVER SIDE SQUIB 2ND STEP) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the steering pad.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Driver Side Squib 2nd Step |
| *2 | Spiral Cable |
| *3 | Center Airbag Sensor |
| *4 | Connector E |
| *5 | SST |
| *a | Front view of wire harness connector (to Driver Side Squib 2nd Step) |
| *b | Color: Black |
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector E.
![]() |
Check that the spiral cable connectors (on the steering pad side) are not damaged.
| *1 | Driver Side Squib 2nd Step |
| *2 | Spiral Cable |
| *3 | Center Airbag Sensor |
|
| ||||
| OK | |
| 3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT |
![]() |
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z13-2 (D2+) - Body ground | Ignition switch ON | Below 1 V |
| z13-1 (D2-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z13-2 (D2+) - z13-1 (D2-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| z13-2 (D2+) - z13-1 (D2-) | Always | 1 MΩ or higher |
| z13-2 (D2+) - Body ground | Always | 1 MΩ or higher |
| z13-1 (D2-) - Body ground | Always | 1 MΩ or higher |
| *1 | Driver Side Squib 2nd Step |
| *2 | Spiral Cable |
| *3 | Center Airbag Sensor |
| *4 | Connector E |
| *a | Front view of wire harness connector (to Driver Side Squib 2nd Step) |
| *b | Color: Black |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR |
![]() |
Connect the connectors to the steering pad and center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Driver Side Squib 2nd Step |
| *2 | Spiral Cable |
| *3 | Center Airbag Sensor |
|
| ||||
| OK | ||
| ||
| 5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - SPIRAL CABLE) |
![]() |
Restore the released activation prevention mechanism of connector B to its original condition.
Disconnect the instrument panel wire connector from the spiral cable.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| F24-4 (D2+) - Body ground | Ignition switch ON | Below 1 V |
| F24-3 (D2-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F24-4 (D2+) - F24-3 (D2-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| F24-4 (D2+) - F24-3 (D2-) | Always | 1 MΩ or higher |
| F24-4 (D2+) - Body ground | Always | 1 MΩ or higher |
| F24-3 (D2-) - Body ground | Always | 1 MΩ or higher |
| *1 | Instrument Panel Wire |
| *2 | Spiral Cable |
| *3 | Center Airbag Sensor |
| *4 | Connector C |
| *5 | SST |
| *a | Rear view of wire harness connector (to Spiral Cable) |
|
| ||||
| OK | ||
| ||