Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1815/54    Short in Front Passenger Side Squib 2nd Step Circuit

DTC    B1816/54    Open in Front Passenger Side Squib 2nd Step Circuit

DTC    B1817/54    Short to GND in Front Passenger Side Squib 2nd Step Circuit

DTC    B1818/54    Short to B+ in Front Passenger Side Squib 2nd Step Circuit

for Preparation Click here


DESCRIPTION

The front passenger side squib 2nd step circuit consists of the center airbag sensor and instrument panel passenger airbag.
The circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the front passenger side squib 2nd step circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1815/54
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal 5 times in the front passenger side squib 2nd step circuit during the primary check.
  2. A front passenger side squib 2nd step malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Instrument panel passenger airbag assembly (Front passenger side squib 2nd step)
  4. Center airbag sensor assembly
B1816/54
One of the following conditions is met:
  1. The center airbag sensor detects an open circuit signal in the front passenger side squib 2nd step circuit for 2 seconds.
  2. A front passenger side squib 2nd step malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Instrument panel passenger airbag assembly (Front passenger side squib 2nd step)
  4. Center airbag sensor assembly
B1817/54
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to ground signal in the front passenger side squib 2nd step circuit for 0.5 seconds.
  2. A front passenger side squib 2nd step malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Instrument panel passenger airbag assembly (Front passenger side squib 2nd step)
  4. Center airbag sensor assembly
B1818/54
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to B+ signal in the front passenger side squib 2nd step circuit for 0.5 seconds.
  2. A front passenger side squib 2nd step malfunction.
  3. A center airbag sensor malfunction.
  1. Instrument panel wire
  2. No. 2 instrument panel wire
  3. Instrument panel passenger airbag assembly (Front passenger side squib 2nd step)
  4. Center airbag sensor assembly

WIRING DIAGRAM


C146249E62


INSPECTION PROCEDURE

NOTICE:
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter check mode (signal check) with the Techstream (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).

1.CHECK INSTRUMENT PANEL PASSENGER AIRBAG (FRONT PASSENGER SIDE SQUIB 2ND STEP)


    C218289E02
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the instrument panel passenger airbag.

  1. Connect the white wire side of SST (resistance: 2.1 Ω) to connector E (black connector).

    CAUTION:
    Never connect the tester to the instrument panel passenger airbag (front passenger side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1815, B1816, B1817 or B1818 is not output.

    HINT:
    Codes other than DTC B1815, B1816, B1817 and B1818 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Passenger Side Squib 2nd Step
    *2
    Center Airbag Sensor
    *3
    Connector E
    *4
    SST
    *a
    Front view of wire harness connector
    (to Front Passenger Side Squib 2nd Step)
    *b
    Color: Black



NG
Go to step 2
OK

REPLACE INSTRUMENT PANEL PASSENGER AIRBAG ASSEMBLY (Click here)  

2.CHECK CONNECTOR
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector E.



    C214773E01
  1. Check that the instrument panel wire connectors (on the instrument panel passenger airbag side) are not damaged.

    OK:
    The lock button is not disengaged, and the claw of the lock is not damaged or deformed.

    Text in Illustration 
    *1
    Front Passenger Side Squib 2nd Step
    *2
    Center Airbag Sensor



NG
REPLACE NO. 2 INSTRUMENT PANEL WIRE
OK


3.CHECK FRONT PASSENGER SIDE SQUIB 2ND STEP CIRCUIT


    C218290E02
  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    z2-1 (P2+) - Body ground
    Ignition switch ON
    Below 1 V
    z2-2 (P2-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-1 (P2+) - z2-2 (P2-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z2-1 (P2+) - z2-2 (P2-)
    Always
    1 MΩ or higher
    z2-1 (P2+) - Body ground
    Always
    1 MΩ or higher
    z2-2 (P2-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Front Passenger Side Squib 2nd Step
*2
Center Airbag Sensor
*3
Connector E
*a
Front view of wire harness connector
(to Front Passenger Side Squib 2nd Step)
*b
Color: Black


NG
Go to step 5
OK


4.CHECK CENTER AIRBAG SENSOR


    C146252E05
  1. Connect the connectors to the instrument panel passenger airbag and center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1815, B1816, B1817 or B1818 is not output.

    HINT:
    Codes other than DTC B1815, B1816, B1817 and B1818 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Front Passenger Side Squib 2nd Step
    *2
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK INSTRUMENT PANEL WIRE (CENTER AIRBAG SENSOR - NO. 2 INSTRUMENT PANEL WIRE)


    C213944E01
  1. Restore the released activation prevention mechanism of connector B to its original condition.

  1. Disconnect the instrument panel wire connector from the No. 2 instrument panel wire.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Fz1-3 - Body ground
    Ignition switch ON
    Below 1 V
    Fz1-4 - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Fz1-3 - Fz1-4
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Fz1-3 - Fz1-4
    Always
    1 MΩ or higher
    Fz1-3 - Body ground
    Always
    1 MΩ or higher
    Fz1-4 - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Front Passenger Side Squib 2nd Step
*2
No. 2 Instrument Panel Wire
*3
Instrument Panel Wire
*4
Center Airbag Sensor
*5
Connector C
*a
Front view of wire harness connector
(to No. 2 Instrument Panel Wire)


NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE NO. 2 INSTRUMENT PANEL WIRE