Home › Audio / Visual / Telematics › AUDIO / VIDEO › AUDIO AND VISUAL SYSTEM

AUDIO AND VISUAL SYSTEM > Illumination Circuit

for Preparation Click here


DESCRIPTION

Power is supplied to the radio and display receiver assembly and steering pad switch illumination when the light control switch is in the tail or head position.

WIRING DIAGRAM


E226612E28


INSPECTION PROCEDURE

NOTICE:
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.
  2. The vehicle is equipped with an SRS (Supplemental Restraint System). Before servicing (including removal or installation of parts), be sure to read the precaution for Supplemental Restraint System (Click here).

1.CHECK ILLUMINATION
  1. Check if the illumination for the radio and display receiver assembly, steering pad switch assembly, glove box or others (hazard switch, transmission control switch, etc.) comes on when the light control switch is turned to the tail or head position.

    Result:

    Result
    Proceed to
    Illumination comes on for all components except steering pad switch assembly.
    A
    Illumination comes on for all components except radio and display receiver assembly.
    B
    Illumination comes on for all components except radio and display receiver assembly and steering pad switch assembly.
    C
    No illumination comes on (radio and display receiver assembly, steering pad switch assembly, hazard switch, glove box, etc.).
    D



B
Go to step 5

C
GO TO METER / GAUGE SYSTEM

D
GO TO LIGHTING SYSTEM
A


2.CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE SUB-ASSEMBLY)
E120026E33
  1. Disconnect the F23 spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F23-12 (IL+2) - Body ground
    Light control switch at tail or head
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Spiral Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT SPIRAL CABLE SUB-ASSEMBLY
  1. Inspect the spiral cable sub-assembly (Click here).

NOTICE:
The spiral cable sub-assembly is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable sub-assembly may prevent the airbag from deploying. Refer to the pages shown in the brackets.

HINT:
  1. Removal (Click here)
  2. Installation (Click here)



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


4.INSPECT STEERING PAD SWITCH ASSEMBLY
  1. Remove the steering pad switch assembly (Click here).

  1. Inspect the steering pad switch assembly (Click here).

    HINT:
    Only perform "Check the illumination".



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

5.CHECK HARNESS AND CONNECTOR (BATTERY - RADIO AND DISPLAY RECEIVER)
E277492E54
  1. Disconnect the G48 radio and display receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G48-10 (ILL+) - Body ground
    Light control switch at tail or head
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Radio and Display Receiver Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (RADIO AND DISPLAY RECEIVER - COMBINATION METER ASSEMBLY)
  1. Disconnect the G47 radio and display receiver assembly connector.

  1. Disconnect the F14 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G47-5 (ILL-) - F14-11 (ILL-)
    Always
    Below 1 Ω
    G47-5 (ILL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)