Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

DTC    B1244    Light Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal, and outputs it to the main body ECU. The main body ECU turns on or off the headlights and taillights according to the signal.

DTC Code
DTC Detection Condition
Trouble Area
B1244
  1. Malfunction in automatic light control sensor.
  2. Open or short in automatic light control sensor circuit.
  1. Automatic light control sensor
  2. Main body ECU (multiplex network body ECU)
  3. Harness or connector

WIRING DIAGRAM


E188439E02


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1244 output does not occur.



NG
Go to step 2
OK

USE SIMULATION METHOD TO CHECK (Click here)  

2.READ VALUE USING TECHSTREAM (AUTOMATIC LIGHT CONTROL SENSOR)
  1. Using the Techstream, read the Data List (Click here).

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Illumination Rate Info
    Illumination rate information / 0 ms. to 99.99 ms.
    Value is output according to ambient light levels
    -

    OK:
    Normal condition listed above is displayed.



NG
Go to step 3
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)  

3.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - AUTOMATIC LIGHT CONTROL SENSOR)
  1. Disconnect the F9 main body ECU connector.

  1. Disconnect the G2 automatic light control sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F9-22 (CLTE) - G2-3 (CLTE)
    Always
    Below 1 Ω
    F9-21 (CLTS) - G2-5 (CLTS)
    Always
    Below 1 Ω
    F9-20 (CLTB) - G2-6 (CLTB)
    Always
    Below 1 Ω
    F9-22 (CLTE) - Body ground
    Always
    10 kΩ or higher
    F9-21 (CLTS) - Body ground
    Always
    10 kΩ or higher
    F9-20 (CLTB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)


    E203228E01
  1. Reconnect the F9 main body ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F9-20 (CLTB) - F9-22 (CLTE)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Component with harness connected
    (Main Body ECU)



NG
REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)
OK


5.CHECK AUTOMATIC LIGHT CONTROL SENSOR


    E203229E01
  1. Reconnect the G2 automatic light control sensor connector.

  1. Connect an oscilloscope to the automatic light control sensor connector.



    B113714E01
  1. Check the waveform.

    OK:
    Tester Connection
    Tool Setting
    Switch Condition
    Specified Condition
    G2-3 (CLTE) - G2-5 (CLTS)
    5 V/DIV., 5 ms./DIV.
    Ignition switch ON, headlight dimmer switch in AUTO position
    Correct waveform is as shown

    Text in Illustration 
    *a
    Component with harness connected
    (Automatic Light Control Sensor)

    HINT:
    If the ambient light becomes brighter, width A becomes narrower.



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR (Click here)
OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) (Click here)