Home › Vehicle Interior › METER / GAUGE / DISPLAY › METER / GAUGE SYSTEM

METER / GAUGE SYSTEM > Speedometer Malfunction

for Preparation Click here


DESCRIPTION

The combination meter receives vehicle speed signals from the skid control ECU via the CAN communication line. The wheel speed sensors output voltages that vary according to the vehicle speed. The skid control ECU supplies power to the wheel speed sensors. The skid control ECU calculates the vehicle speed based on the pulses of the voltage.

WIRING DIAGRAM


E200122E01


INSPECTION PROCEDURE

NOTICE:
If the vehicle speed is outside the allowable range when tested, perform the on-vehicle inspection (Click here).

HINT:
Before starting the following inspection, check tire size and tire air pressure.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication DTC is output (Click here).
    Result 
    Result
    Proceed to
    CAN communication DTC is not output
    A
    CAN communication DTC is output
    B



B
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (SPEED METER OPERATION)
  1. Use the Active Test to check the operation of the speedometer (Click here).

    Combination Meter 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Speed Meter Operation
    Speedometer
    0, 40, 80, 120, 160, 200 mph*1
    Acceptable range (mph): [Control range → Speedometer display]
    1. 40 → 40 to 43.5
    2. 80 → 80 to 84.5
    Confirm that the vehicle is stopped with the engine idling.
    0, 40, 80, 120, 160, 200 km/h*2
    Acceptable range (km/h): [Control range → Speedometer display]
    1. 40 → 38 to 42
    2. 80 → 78 to 84
    3. 120 → 119 to 125
    4. 160 → 159 to 167
    Confirm that the vehicle is stopped with the engine idling.

    1. *1: for U.S.A.
    2. *2: except U.S.A.

    OK:
    Speedometer indication is normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK


3.READ VALUE USING TECHSTREAM (VEHICLE SPEED METER)
  1. Use the Data List to check if the speedometer is operating properly (Click here).

    Combination Meter 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Vehicle Speed Meter
    Vehicle speed/Min.: 0 mph (0 km/h), Max.: 255 km/h (158 mph)
    Almost the same as actual vehicle speed measured using a speedometer tester
    -

    OK:
    Vehicle speed displayed on the Techstream is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
Go to step 4
OK

REPLACE COMBINATION METER ASSEMBLY (Click here)  

4.READ VALUE USING TECHSTREAM (FR/FL/RR/RL WHEEL SPEED)
  1. Use the Data List to check the wheel speed (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    FR Wheel Speed
    Vehicle speed/Min.: 0 mph (0 km/h), Max.: 326 km/h (202 mph)
    Almost the same as actual vehicle speed measured using a speedometer tester
    -
    FL Wheel Speed
    Vehicle speed/Min.: 0 mph (0 km/h), Max.: 326 km/h (202 mph)
    Almost the same as actual vehicle speed measured using a speedometer tester
    -
    RR Wheel Speed
    Vehicle speed/Min.: 0 mph (0 km/h), Max.: 326 km/h (202 mph)
    Almost the same as actual vehicle speed measured using a speedometer tester
    -
    RL Wheel Speed
    Vehicle speed/Min.: 0 mph (0 km/h), Max.: 326 km/h (202 mph)
    Almost the same as actual vehicle speed measured using a speedometer tester
    -

    OK:
    Vehicle speed displayed on the Techstream is almost the same as the actual vehicle speed measured using a speedometer tester (calibrated chassis dynamometer).



NG
GO TO VEHICLE STABILITY CONTROL SYSTEM (Click here)
OK


5.REPLACE MASTER CYLINDER SOLENOID
  1. Replace the skid control ECU with a new or normally functioning one (Click here).

    OK:
    The operation of the speedometer returns to normal.



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

END