Home › Vehicle Interior › SEAT BELT › SEAT BELT WARNING SYSTEM

SEAT BELT WARNING SYSTEM > Front Passenger Side Seat Belt Warning Light Malfunction

for Preparation Click here


DESCRIPTION

When the ignition switch is ON, the occupant detection ECU sends a signal to the airbag sensor assembly to indicate the state of the front seat inner belt assembly RH and also whether the front passenger seat is occupied. The airbag sensor assembly sends those signals to the combination meter assembly via CAN communication. The combination meter assembly illuminates, blinks or turns off the seat belt warning light on the combination meter assembly in accordance with these signals.

HINT:
The seat belt warning light on the combination meter assembly is used for both the driver seat and front passenger seat.


WIRING DIAGRAM


B355292E01


INSPECTION PROCEDURE

NOTICE:
The seat belt warning system uses the CAN communication system. First, confirm that there is no malfunction in the CAN communication system. Refer to the How to Proceed with Troubleshooting procedure (Click here).

1.CHECK DTC OUTPUT (OCCUPANT CLASSIFICATION SYSTEM)
  1. Clear DTCs (Click here).

  1. Recheck for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO OCCUPANT CLASSIFICATION SYSTEM (Click here)
A


2.CHECK DTC OUTPUT (AIRBAG SYSTEM)
  1. Clear DTCs (Click here).

  1. Recheck for DTCs (Click here).

    Result:
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    B



B
GO TO AIRBAG SYSTEM (Click here)
A


3.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Occupant Detection / Data List.

  1. Read the Data List according to the display on the Techstream.

    Occupant Detection 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Passenger Buckle SW
    Front passenger side buckle switch / Unset, Set or NG
    Unset: Front passenger side seat belt unfastened
    Set: Front passenger side seat belt fastened
    NG: Condition undetermined
    -
    Result 
    Result
    Proceed to
    Unset or Set is displayed on the Techstream screen according to the front passenger seat belt condition
    A
    Unset or Set is not displayed normally on the Techstream screen according to the front passenger seat belt condition
    B
    NG is displayed on the Techstream screen
    C



B
REPLACE FRONT SEAT INNER BELT ASSEMBLY RH (Click here)

C
REPLACE OCCUPANT DETECTION ECU (Click here)
A


4.READ VALUE USING TECHSTREAM
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / SRS Airbag / Data List.

  1. Read the Data List according to the display on the Techstream.

    SRS Airbag 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Right side Buckle SW
    Front RH side seat belt buckle switch / Unset, Set or NG
    Unset: Seat belt unfastened
    Set: Seat belt fastened
    NG: Condition undetermined
    -
    Result 
    Result
    Proceed to
    Unset or Set is displayed on the Techstream screen according to the front passenger seat belt condition
    A
    1. Unset or Set is not displayed normally on the Techstream screen according to the front passenger seat belt condition
    2. NG is displayed on the Techstream screen
    B



B
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)