Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

DTC    C1380    Stop Light Control Relay Malfunction

for Preparation Click here


DESCRIPTION

Upon receiving the hill-start assist control operating signal from the master cylinder solenoid (skid control ECU), the Stop light control relay (Stop light switch assembly) contact turns on and the stop lights come on.

DTC No.
DTC Detection Condition
Trouble Area
C1380
  1. When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STPO) is ON, a signal is not input to the STP2 terminal for 5 seconds or more.
  1. When the voltage at the IG1 terminal is 9.5 V or more and the stop light control relay drive output (STPO) is OFF, the signal at the STP terminal is different from the input signal at the STP2 for 5 seconds or more.
  1. Stop light control relay (Stop light switch assembly)
  2. Stop light control relay (Stop light switch assembly) circuit
  3. Master cylinder solenoid (Skid control ECU)

WIRING DIAGRAM


C252945E02


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform calibration (Click here).
  1. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
When DTC C1425 is output together with DTC C1380, inspect and repair the trouble areas indicated by DTC C1425 first (Click here).

1.CHECK STOP LIGHT OPERATION
  1. Check that the stop lights come on when the brake pedal is depressed and go off when the brake pedal is released.

    OK:
    Condition
    Illumination Condition
    Brake pedal depressed.
    ON
    Brake pedal released.
    OFF



NG
INSPECT LIGHTING SYSTEM (STOP LIGHT CIRCUIT) (Click here)
OK


2.READ VALUE USING TECHSTREAM (STOP LIGHT SW)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Select the Data List on the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW
    Stop light switch assembly / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

  1. Check that the stop light switch assembly condition observed on the Techstream changes according to brake pedal operation.

    OK:
    The Techstream displays ON or OFF according to brake pedal operation.



NG
Go to step 8
OK


3.PERFORM ACTIVE TEST USING TECHSTREAM (STOP LIGHT RELAY)
  1. Select the Active Test on the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Stop Light Relay
    Stop light control relay (Stop light switch assembly)
    Relay (Switch) ON/OFF
    Stop lights come on

  1. Perform the Active Test of the stop light control relay (stop light switch assembly) using the Techstream.

  1. Select the Data List on the Techstream (Click here).

    ABS/VSC/TRAC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light Relay Output
    Stop light control relay (Stop light switch assembly) output / ON or OFF
    ON: Relay output on
    OFF: Relay output off
    -

  1. Check for stop light control relay (stop light switch assembly) operation using the Data List and stop light operation by performing an Active Test.

    Result:
    Result
    Proceed to
    Data List content and stop light operation are normal.
    A
    Data List content and stop light operation are abnormal or Data List content is normal but stop lights do not turn on or off.
    B



B
Go to step 6
A


4.CHECK HARNESS AND CONNECTOR (STP2 TERMINAL)


    C214161E25
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the A6 skid Control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A6-45 (STP2) - Body ground
    Stop light switch assembly ON (Brake pedal depressed)
    11 to 14 V
    A6-45 (STP2) - Body ground
    Stop light switch assembly OFF (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP2 CIRCUIT)
OK


5.RECONFIRM DTC
  1. Reconnect the skid control ECU connector.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch to ON.

  1. Perform a road test.

  1. Check if the same DTC is output (Click here).

    Result:
    Result
    Proceed to
    DTC C1380 is not output.
    A
    DTC C1380 is output.
    B



B
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

6.CHECK STOP LIGHT SWITCH ASSEMBLY
  1. Check the stop light control relay (stop light switch assembly) (Click here).

    OK:
    The stop light control relay (stop light switch assembly) is normal.



NG
REPLACE STOP LIGHT SWITCH ASSEMBLY (Click here)
OK


7.CHECK HARNESS AND CONNECTOR (STPO TERMINAL)


    C214161E26
  1. Make sure that there is no looseness at the locking part and the connecting part of the connectors.

  1. Disconnect the A6 skid control ECU connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A6-16 (STPO) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STPO CIRCUIT)
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)  

8.CHECK HARNESS AND CONNECTOR (STP TERMINAL)


    C214161E24
  1. Turn the ignition switch off.

  1. Make sure that there is no looseness at the locking part and the connecting part of the connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A6-7 (STP) - Body ground
    Stop light switch assembly ON (Brake pedal depressed)
    11 to 14 V
    A6-7 (STP) - Body ground
    Stop light switch assembly OFF (Brake pedal released)
    Below 1.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (STP CIRCUIT)
OK

REPLACE MASTER CYLINDER SOLENOID (Click here)