Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1660/43    Passenger Airbag ON/OFF Indicator Circuit Malfunction

for Preparation Click here


DESCRIPTION

The passenger airbag ON/OFF indicator circuit consists of the airbag sensor assembly and passenger airbag ON/OFF indicator.
The passenger airbag ON/OFF indicator indicates the operation condition of the instrument panel passenger airbag, lower No. 2 instrument panel airbag, front seat side airbag RH and front seat outer belt RH.
DTC B1660/43 is stored when a malfunction is detected in the passenger airbag ON/OFF indicator circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1660/43
One of the following conditions is met:
  1. The airbag sensor assembly detects an open circuit signal, short circuit to ground signal or short circuit to B+ signal in the passenger airbag ON/OFF indicator circuit for 2 seconds.
  2. A passenger airbag ON/OFF indicator malfunction.
  3. An airbag sensor assembly malfunction.
  1. Instrument panel wire
  2. Telltale light assembly
  3. Airbag sensor assembly

WIRING DIAGRAM


C294112E01


INSPECTION PROCEDURE

NOTICE:
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

1.CHECK PASSENGER AIRBAG ON/OFF INDICATOR CONDITION


  1. Turn the ignition switch to ON.


    C123768E73

  1. Check the passenger airbag ON/OFF indicator operation.

    HINT:
    Refer to the normal condition of the passenger airbag ON/OFF indicator (Click here).

    Result 
    Result
    Proceed to
    Always on
    A
    Off
    B



B
Go to step 7
A


2.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the airbag sensor assembly and telltale light assembly.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


3.CHECK CONNECTORS
  1. Disconnect the connectors from the airbag sensor assembly and telltale light assembly.



    C214663E01
  1. Check that the connectors (on the airbag sensor assembly side and telltale light assembly side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Text in Illustration 
    *1
    Telltale Light Assembly
    *2
    Airbag Sensor Assembly



NG
REPLACE INSTRUMENT PANEL WIRE
OK


4.CHECK PASSENGER AIRBAG ON/OFF INDICATOR


    C213929
  1. Connect the connector to the telltale light assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON.

  1. Check the passenger airbag ON/OFF indicator operation.

    OK:
    The passenger airbag ON/OFF indicator does not come on.



NG
Go to step 6
OK


5.CHECK AIRBAG SENSOR ASSEMBLY


    C214664E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Connect the connector to the airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660 is not output.

    HINT:
    Codes other than DTC B1660 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Telltale Light Assembly
    *2
    Airbag Sensor Assembly



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

6.CHECK INSTRUMENT PANEL WIRE (AIRBAG SENSOR - TELLTALE LIGHT)


  1. Turn the ignition switch off.


    C213930E03


    Text in Illustration 
    *1
    Telltale Light Assembly
    *2
    Airbag Sensor Assembly
    *3
    Connector C
    *4
    Connector B
    *5
    Service Wire
    -
    -
    *a
    Front view of wire harness connector
    (to Telltale Light Assembly)
    *b
    Rear view of wire harness connector
    (to Airbag Sensor Assembly)

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connectors from the airbag sensor assembly and telltale light assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F32-3 (PAON) - Body ground
    Ignition switch ON
    Below 1 V
    F32-4 (P-AB) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F32-3 (PAON) - F32-4 (P-AB)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F32-3 (PAON) - F32-4 (P-AB)
    Always
    1 MΩ or higher
    F32-3 (PAON) - Body ground
    Always
    1 MΩ or higher
    F32-4 (P-AB) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK

REPLACE TELLTALE LIGHT ASSEMBLY (Click here)  

7.CHECK CONNECTION OF CONNECTORS
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Check that the connectors are properly connected to the airbag sensor assembly and telltale light assembly.

    OK:
    The connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


8.CHECK CONNECTORS
  1. Disconnect the connectors from the airbag sensor assembly and telltale light assembly.



    C214663E01
  1. Check that the connectors (on the airbag sensor assembly side and telltale light assembly side) are not damaged.

    OK:
    The connectors are not deformed or damaged.

    Text in Illustration 
    *1
    Telltale Light Assembly
    *2
    Airbag Sensor Assembly



NG
REPLACE INSTRUMENT PANEL WIRE
OK


9.CHECK INSTRUMENT PANEL WIRE (AIRBAG SENSOR - TELLTALE LIGHT)


  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


    C213930E03


    Text in Illustration 
    *1
    Telltale Light Assembly
    *2
    Airbag Sensor Assembly
    *3
    Connector C
    *4
    Connector B
    *5
    Service Wire
    -
    -
    *a
    Front view of wire harness connector
    (to Telltale Light Assembly)
    *b
    Rear view of wire harness connector
    (to Airbag Sensor Assembly)

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F32-3 (PAON) - Body ground
    Ignition switch ON
    Below 1 V
    F32-4 (P-AB) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Using a service wire, connect terminals 23 (PAON) and 17 (P-AB) of connector B.

    NOTICE:
    Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F32-3 (PAON) - F32-4 (P-AB)
    Always
    Below 1 Ω

  1. Disconnect the service wire from connector B.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F32-3 (PAON) - F32-4 (P-AB)
    Always
    1 MΩ or higher
    F32-3 (PAON) - Body ground
    Always
    1 MΩ or higher
    F32-4 (P-AB) - Body ground
    Always
    1 MΩ or higher



NG
REPLACE INSTRUMENT PANEL WIRE
OK


10.CHECK PASSENGER AIRBAG ON/OFF INDICATOR (SOURCE VOLTAGE)


    C213931E03
  1. Turn the ignition switch off.

  1. Connect the connectors to the airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F32-7 (IG+) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Telltale Light Assembly)



NG
REPLACE HARNESS AND CONNECTOR (TELLTALE LIGHT - BATTERY) OR BATTERY
OK


11.CHECK PASSENGER AIRBAG ON/OFF INDICATOR


    C213932E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Connect the connector to the telltale light assembly.

  1. Disconnect the connectors from the airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Check the indicator according to the value(s) in the table below.

    OK:
    Tester Connection
    Switch Condition
    Passenger airbag ON/OFF indicator
    F33-23 (PAON) - Body ground
    Ignition switch ON
    "ON" comes on
    F33-17 (P-AB) - Body ground
    Ignition switch ON
    "OFF" comes on

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Airbag Sensor Assembly)



NG
REPLACE TELLTALE LIGHT ASSEMBLY (Click here)
OK


12.CHECK AIRBAG SENSOR ASSEMBLY


    C214664E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Connect the connectors to the airbag sensor assembly.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1660 is not output.

    HINT:
    Codes other than DTC B1660 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Telltale Light Assembly
    *2
    Airbag Sensor Assembly



NG
REPLACE AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)