Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0420    Catalyst System Efficiency Below Threshold (Bank 1)

DTC    P0430    Catalyst System Efficiency Below Threshold (Bank 2)

for Preparation Click here


DESCRIPTION

The ECM uses sensors mounted in front of and behind the Three-Way Catalytic Converter (TWC) to monitor its efficiency.
The first sensor, the air fuel ratio sensor, sends pre-catalyst information to the ECM. The second sensor, the heated oxygen sensor, sends post-catalyst information to the ECM.
In order to detect any deterioration in the three-way catalytic converter, the ECM calculates the oxygen storage capacity of the three-way catalytic converter. This calculation is based on the voltage output of the heated oxygen sensor while performing active air fuel ratio control.
The oxygen storage capacity value is an indication of the oxygen storage capacity of the three-way catalytic converter. When the vehicle is being driven with a warm engine, active air fuel ratio control is performed for approximately 15 to 20 seconds. When it is performed, the ECM deliberately sets the air fuel ratio to lean or rich levels. If the cycle of the waveform for the heated oxygen sensor is long, the oxygen storage capacity is great. There is a direct correlation between the heated oxygen sensor and the oxygen storage capacity of the three-way catalytic converter.
The ECM uses the oxygen storage capacity value to determine the state of the three-way catalytic converter. If any deterioration has occurred, the ECM illuminates the MIL and sets the DTC.
This system determines the deterioration of the entire catalyst system (including the front and rear catalysts), by using the oxygen storage capacity value of the front catalyst, that is more sensitive than the rear catalyst, as the representative value. Therefore, be sure to replace the front and rear catalysts together when catalyst replacement is necessary.

DTC No.
DTC Detection Condition
Trouble Area
P0420
OSC value is less than the standard value under active air-fuel ratio control (1 trip detection logic)
  1. Gas leakage from exhaust system
  2. Air fuel ratio sensor (bank 1 sensor 1)
  3. Heated oxygen sensor (bank 1 sensor 2)
  4. Exhaust manifold sub-assembly RH (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)
P0430
OSC value is less than the standard value under active air-fuel ratio control (1 trip detection logic)
  1. Gas leakage from exhaust system
  2. Air fuel ratio sensor (bank 2 sensor 1)
  3. Heated oxygen sensor (bank 2 sensor 2)
  4. Exhaust manifold sub-assembly LH (TWC: Front catalyst) and front exhaust pipe assembly (TWC: Rear catalyst)

CATALYST LOCATION


A223836E01


Text in Illustration 
*1
Exhaust Manifold Sub-assembly RH (TWC: Front catalyst)
*2
Exhaust Manifold Sub-assembly LH (TWC: Front catalyst)
*3
Front Exhaust Pipe (TWC: Rear catalyst)
*4
Front No. 2 Exhaust Pipe (TWC: Rear catalyst)
*5
Center Exhaust Pipe Assembly
*6
Tailpipe Assembly
*7
Air Fuel Ratio Sensor (for Bank 1 Sensor 1)
*8
Air Fuel Ratio Sensor (for Bank 2 Sensor 1)
*9
Heated Oxygen Sensor (for Bank 1 Sensor 2)
*10
Heated Oxygen Sensor (for Bank 2 Sensor 2)

NOTICE:
  1. When DTC P0420 is output, replace the exhaust manifold sub-assembly RH (*1) and the front exhaust pipe (*3) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor *7 and heated oxygen sensor *9)
  2. When DTC P0430 is output, replace the exhaust manifold sub-assembly LH (*2) and the No. 2 front exhaust pipe (*4) together when catalyst replacement is necessary. (Excluding air fuel ratio sensor *8 and heated oxygen sensor *10)


MONITOR STRATEGY


Related DTCs
P0420: Catalyst deterioration (bank 1)
P0430: Catalyst deterioration (bank 2)
Required Sensors/Components (Main)
Air fuel ratio sensor and heated oxygen sensor
Required Sensors/Components (Related)
Intake air temperature sensor, mass air flow meter, crankshaft position sensor and engine coolant temperature sensor
Frequency of Operation
Once per driving cycle
Duration
About 30 seconds
MIL Operation
1 driving cycle
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Monitor runs whenever following DTCs are not present
P219A, P219B (Air-Fuel Ratio Imbalance)
P0010, P0020 (Camshaft Timing Oil Control Valve Assembly bank 1, 2)
P0011, P0021 (VVT System Bank 1, 2 - Advance)
P0012, P0022 (VVT System Bank 1, 2 - Retard)
P0013, P0023 (Exhaust Camshaft Timing Oil Control Valve Assembly Bank 1, 2)
P0014, P0024 (Exhaust VVT System Bank 1, 2 - Advance)
P0015, P0025 (Exhaust VVT System Bank 1, 2 - Retard)
P0016, P0018 (VVT System Bank 1, 2 - Misalignment)
P0017, P0019 (Exhaust VVT System Bank 1, 2 - Misalignment)
P0031, P0032, P0051, P0052, P101D, P103D (Air Fuel Ratio Sensor Heater)
P0037, P0038, P0057, P0058, P102D, P105D (Heated Oxygen Sensor Heater)
P0102, P0103 (Mass Air Flow Meter)
P0107, P0108 (Manifold Absolute Pressure)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0120, P0121, P0122, P0123, P0220, P0222, P0223, P2135 (Throttle Position Sensor)
P0125 (Insufficient Engine Coolant Temperature for Closed Loop Fuel Control)
P0136, P0137, P0138, P0139, P013A (Heated Oxygen Sensor Bank 1)
P014C, P014D, P014E, P014F (Air Fuel Ratio Sensor - Slow Response)
P015A, P015B, P015C, P015D (Air Fuel Ratio Sensor - Delayed Response)
P013C, P0156, P0157, P0158, P0159 (Heated Oxygen Sensor Bank 2)
P0171, P0172, P0174, P0175 (Fuel System)
P0301, P0302, P0303, P0304, P0305, P0306 (Misfire)
P0335 (Crankshaft Position Sensor)
P0340, P0342, P0343, P0345, P0347, P0348 (VVT Sensor)
P0351, P0352, P0353, P0354, P0355, P0356 (Igniter)
P0365, P0367, P0368, P0390, P0392, P0393 (Exhaust VVT Sensor)
P0500 (Vehicle Speed Sensor)
P0607 (Heated Oxygen Sensor - Sensor 2)
P2195, P2196, P2197, P2198 (Air Fuel Ratio Sensor - Rationality)
P2237, P2240 (Air Fuel Ratio Sensor - Open)
P2238, P2241, P2252, P2255 (Air Fuel Ratio Sensor - Low Impedance)
P2239, P2242, P2253, P2256 (Air Fuel Ratio Sensor - High Impedance)
P0412, P0418, P1613 (Secondary Air Injection System Control)
P0416, P0417, P2440, P2441, P2442, P2443, P2444, P2445 (Secondary Air Injection System)
P219A, P219B (Air-Fuel Ratio Imbalance)
Auxiliary battery voltage
11 V or more
Intake air temperature
-10°C (14°F) or more
Engine coolant temperature
75°C (167°F) or more
Atmospheric pressure
76 kPa(abs) [570 mmHg(abs)] or more
Idle
Off
Engine speed
Less than 3200 rpm
Air fuel ratio sensor
Activated
Fuel system status
Closed loop
Engine load
10 to 70%
All of the following conditions are met:
Conditions 1, 2 and 3
1. Mass air flow
5 to 75 g/sec
2. Front catalyst temperature (estimated)
690 to 860°C (1274 to 1580°F)
3. Rear catalyst temperature (estimated)
500 to 900°C (932 to 1652°F)
Shift position
4th or higher

TYPICAL MALFUNCTION THRESHOLDS


Oxygen Storage Capacity (OSC) of catalyst (Normalized)
Less than 1

MONITOR RESULT

Refer to Checking Monitor Status (Click here).

CONFIRMATION DRIVING PATTERN

HINT:
  1. It is necessary that the response of the heated oxygen sensor is normal in order to confirm DTC P0420 and P0430. Therefore, perform the driving pattern for the heated oxygen sensor monitor before performing the drive pattern for the catalyst efficiency monitor.
  2. Performing this confirmation driving pattern will activate the catalyst efficiency monitor. This is very useful for verifying the completion of a repair.


A283604E06

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON.
  3. Turn the Techstream on.
  4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  5. Turn the ignition switch off and wait for at least 30 seconds.
  6. Turn the ignition switch to ON and turn the Techstream on.
  7. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor.
  8. Check that Catalyst Efficiency / Current is Incomplete.
  9. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [A].
  10. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [B].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    Drive the vehicle while keeping the engine load as constant as possible.

  11. Drive the vehicle at 60 km/h (37 mph), and then decelerate the vehicle by releasing the accelerator pedal for 5 seconds or more to perform the fuel-cut [C].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  12. Enter the following menus: Powertrain / Engine and ECT / Monitor / Current Monitor / O2 Sensor / RL F/C B1S2, RL F/C B2S2 [D].
  13. Check the Test Value for RL F/C B1S2.
    1. If Test Value displays a value larger than 0, perform the following procedure, as the O2 sensor monitor is finished.

      HINT:
      If Test Value displays 0, perform step [C] until it displays a value larger than 0, as the O2 sensor monitor is not finished.

  14. Turn the ignition switch off and wait for at least 30 seconds [F].
  15. Turn the ignition switch to ON and turn the Techstream on.
  16. Start the engine and warm it up until the engine coolant temperature is 75°C (167°F) or higher [G].
  17. Drive the vehicle at approximately 60 km/h (37 mph) for 10 minutes or more [H].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. Drive the vehicle while keeping the engine load as constant as possible.
    2. The monitor item will change to Complete as the Catalyst Efficiency monitor operates [I].

  18. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  19. Check if any DTCs are stored.

    HINT:
    If the monitor item does not change to Complete, and no DTCs are stored, perform the following procedure.

  20. Drive the vehicle at a speed between 75 and 100 km/h (47 and 63 mph) for 10 minutes or more [J].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    HINT:
    1. Drive the vehicle while keeping the engine load as constant as possible.
    2. The monitor item will change to Complete as the Catalyst Efficiency monitor operates [K].

  21. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
  22. Check if any DTCs are stored.

    HINT:
    If the monitor item does not change to Complete, and no DTCs are stored, extend the driving time.

  23. If no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


CONDITIONING FOR SENSOR TESTING

HINT:
Perform the operation with the engine speeds and time durations described below prior to checking the waveforms of the air fuel ratio and heated oxygen sensors. This is in order to activate the sensors sufficiently to obtain the appropriate inspection results.


A093766E57

  1. Connect the Techstream to the DLC3 [A].
  2. Turn the ignition switch to ON and turn the Techstream on [A].
  3. Start the engine and warm it up with all the accessories switched off and the shift lever in P, until the engine coolant temperature stabilizes [B].

    HINT:
    In order to keep the idling stable, turn off the A/C and all other electric loads and do not perform any shift operations.

  4. Run the engine at an engine speed of between 2500 rpm and 3000 rpm for at least 3 minutes [C].

    HINT:
    During charging control, the engine speed is set at idle. Therefore, the engine speed does not increase when depressing the accelerator pedal. In this case, perform step [C] after charging control has completed.

  5. While running the engine at 3000 rpm and 2000 rpm for 2 seconds, check the waveforms of the air fuel ratio and heated oxygen sensors using the Techstream [D].

    HINT:
    1. If either of the voltage outputs of either the air fuel ratio or heated oxygen sensor does not fluctuate, or either of the sensors makes a noise, the sensor may be malfunctioning.
    2. If the voltage outputs of both the sensors remain lean or rich, the air fuel ratio may be extremely lean or rich. In such cases, enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor.
    3. If the three-way catalytic converter has deteriorated, the heated oxygen sensor (located behind the three-way catalytic converter) voltage output fluctuates up and down frequently, even under normal driving conditions (active air fuel ratio control is not performed).


A199479E13


INSPECTION PROCEDURE

HINT:
  1. If a malfunction cannot be found when troubleshooting DTC P0420 or P0430, a lean or rich abnormality may be the cause. Perform troubleshooting by following the inspection procedure for P0171 or P0174 (System Too Lean) and P0172 or P0175 (System Too Rich).
  2. Bank 1 refers to the bank that includes the No. 1 cylinder*.
    *: The No. 1 cylinder is the cylinder which is farthest from transmission.
  3. Bank 2 refers to the bank that does not include the No. 1 cylinder.
  4. Sensor 1 refers to the sensor closest to the engine assembly.
  5. Sensor 2 refers to the sensor farthest away from the engine assembly.
  6. Read freeze frame data using the Techstream. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0420 AND/OR P0430)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P0420 and/or P0430 are output
    A
    DTC P0420 and/or P0430 and other DTCs are output
    B

    HINT:
    If any DTCs other than P0420 or P0430 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (CONTROL THE INJECTION VOLUME FOR A/F SENSOR)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine and warm it up.

  1. Run the engine at an engine speed of 2500 rpm for approximately 90 seconds.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Injection Volume for A/F Sensor / AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2.

  1. Perform the Active Test operation with the engine idling (press the RIGHT or LEFT button to change the fuel injection volume).

  1. Monitor the voltage outputs of the air fuel ratio sensor and heated oxygen sensor (AFS Voltage B1S1 and O2S B1S2 or AFS Voltage B2S1 and O2S B2S2) displayed on the Techstream.

    HINT:
    1. Change the fuel injection volume within the range of -12.5% to 12.5%. The injection volume can be changed in fine gradations.
    2. Each sensor reacts in accordance with increases and decreases in the fuel injection volume.
    3. The air fuel ratio sensor has an output delay of a few seconds and the heated oxygen sensor has a maximum output delay of approximately 20 seconds.
    4. If the sensor output voltage does not change (almost no reaction) while performing the Active Test, the sensor may be malfunctioning.


    Standard:

    Techstream Display
    (Sensor)
    Injection Volume
    Status
    Voltage
    AFS Voltage B1S1 or AFS Voltage B2S1
    (Air fuel ratio)
    12.5%
    Rich
    Below 3.1 V
    -12.5%
    Lean
    Higher than 3.4 V
    O2S B1S2 or O2S B2S2
    (Heated oxygen)
    12.5%
    Rich
    Higher than 0.55 V
    -12.5%
    Lean
    Below 0.4 V


    Result:

    Status
    AFS Voltage B1S1
    or
    AFS Voltage B2S1
    Status
    O2S B1S2
    or
    O2S B2S2
    A/F Condition and A/F and
    HO2 Sensor Conditions
    Misfire
    Main Suspected Trouble Areas
    Proceed to
    Lean/Rich
    Lean/Rich
    Normal
    -
    1. Three-Way Catalytic Converter (TWC)
    2. Gas leakage from exhaust system
    A
    Lean
    Lean/Rich
    Air fuel ratio sensor malfunction
    -
    1. Air fuel ratio sensor
    B
    Rich
    Lean/Rich
    Air fuel ratio sensor malfunction
    May occur
    1. Air fuel ratio sensor
    Lean/Rich
    Lean
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leakage from exhaust system
    C
    Lean/Rich
    Rich
    Heated oxygen sensor malfunction
    -
    1. Heated oxygen sensor
    2. Gas leakage from exhaust system
    Lean
    Lean
    Actual air-fuel ratio lean
    May occur
    1. Extremely rich or lean actual air-fuel ratio
    2. Gas leakage from exhaust system
    D
    Rich
    Rich
    Actual air-fuel ratio lean
    -
    1. Extremely rich or lean actual air-fuel ratio
    2. Gas leakage from exhaust system

    Lean: During Control the Injection Volume for A/F Sensor, the air fuel ratio sensor output voltage (AFS Voltage B1S1 or AFS Voltage B2S1) is consistently higher than 3.4 V, and the heated oxygen sensor output voltage (O2S B1S2 or O2S B2S2) is consistently below 0.4 V.
    Rich: During Control the Injection Volume for A/F Sensor, the AFS Voltage B1S1 or AFS Voltage B2S1 is consistently below 3.1 V, and the O2S B1S2 or O2S B2S2 is consistently higher than 0.55 V.
    Lean/Rich: During Control the Injection Volume for A/F Sensor of the Active Test, the output voltage of the air fuel ratio sensor and heated oxygen sensor alternate correctly.



B
Go to step 7

C
Go to step 5

D
Go to step 6
A


3.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



NG
Go to step 8
OK


4.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

NOTICE:
  1. When DTC P0420 is output, replace the exhaust manifold sub-assembly RH (TWC: Front catalyst) and the front exhaust pipe (TWC: Rear catalyst) together when catalyst replacement is necessary.
  2. When DTC P0430 is output, replace the exhaust manifold sub-assembly LH (TWC: Front catalyst) and the front No. 2 exhaust pipe (TWC: Rear catalyst) together when catalyst replacement is necessary.

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P0420 is output
    A, C
    DTC P0430 is output
    B, D
    DTC P0420 and P0430 are output
    A, B, C, D



A
REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: FRONT CATALYST) (Click here)

B
REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: FRONT CATALYST) (Click here)

C
REPLACE FRONT EXHAUST PIPE (TWC: REAR CATALYST) (Click here)
D

REPLACE FRONT NO. 2 EXHAUST PIPE (TWC: REAR CATALYST) (Click here)  

5.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



OK
Go to step 9

NG
Go to step 8

6.CHECK FOR EXHAUST GAS LEAK
  1. Check for exhaust gas leaks.

    OK:
    No gas leaks.



OK
Go to step 10

NG
Go to step 8

7.REPLACE AIR FUEL RATIO SENSOR
  1. Replace the air fuel ratio sensor (Click here).



NEXT
Go to step 11

8.REPAIR OR REPLACE EXHAUST GAS LEAK POINT
  1. Repair or replace exhaust gas leak point.



NEXT
Go to step 11

9.REPLACE HEATED OXYGEN SENSOR
  1. Replace the heated oxygen sensor (Click here).



NEXT
Go to step 11

10.CHECK CAUSE OF EXTREMELY RICH OR LEARN ACTUAL AIR FUEL RATIO
  1. Check the cause of extremely rich or lean actual air fuel ratio, referring to the DTC P0171 Inspection Procedure .


NEXT


11.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P0420 and/or P0430 is output
    A
    DTC is not output
    B



B
END
A


12.CHECK DTC OUTPUT (DTC P0420 AND/OR P0430)

NOTICE:
  1. When DTC P0420 is output, replace the exhaust manifold sub-assembly RH (TWC: Front catalyst) and the front exhaust pipe (TWC: Rear catalyst) together when catalyst replacement is necessary.
  2. When DTC P0430 is output, replace the exhaust manifold sub-assembly LH (TWC: Front catalyst) and the front No. 2 exhaust pipe assembly (TWC: Rear catalyst) together when catalyst replacement is necessary.

HINT:
Confirm the replacement parts, referring to the illustration in the Catalyst Location.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.

  1. Read the DTCs.

    Result:

    Result
    Proceed to
    DTC P0420 is output
    A, C
    DTC P0430 is output
    B, D
    DTC P0420 and P0430 are output
    A, B, C, D



A
REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY RH (TWC: FRONT CATALYST) (Click here)

B
REPLACE EXHAUST MANIFOLD SUB-ASSEMBLY LH (TWC: FRONT CATALYST) (Click here)

C
REPLACE FRONT EXHAUST PIPE (TWC: REAR CATALYST) (Click here)
D

REPLACE FRONT NO. 2 EXHAUST PIPE (TWC: REAR CATALYST) (Click here)