Home › Drivetrain ยท AXLE AND DIFFERENTIAL › REAR DIFFERENTIAL CARRIER OIL SEAL

REAR DIFFERENTIAL CARRIER OIL SEAL > REPLACEMENT

for Preparation Click here



1. REMOVE REAR PROPELLER SHAFT ASSEMBLY
  1. for 2WD:
    Remove the rear propeller shaft assembly (Click here).

  1. for 4WD:
    Remove the rear propeller shaft assembly (Click here).



2. REMOVE REAR DRIVE PINION NUT


C089309E01
  1. Using SST and a hammer, loosen the staked part of the rear drive pinion nut.

    SST
    09930-00010  

    NOTICE:
    1. Be sure to use SST with the tapered surface facing the shaft.
    2. Do not grind the tip of the SST with a grinder, etc.
    3. Completely loosen the staked part of the nut when removing it.
    4. Do not damage the threads of the drive pinion nut.



    B087842E02
  1. Use SST to hold the companion flange.

    SST
    09330-00021   (09330-00030)

  1. Using a 30 mm socket wrench, remove the rear drive pinion nut.



3. REMOVE REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


C217281E01
  1. Using SST, remove the rear drive pinion companion flange sub-assembly.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



4. REMOVE REAR DIFFERENTIAL CARRIER OIL SEAL


C217279E01
  1. Using SST, remove the rear differential carrier oil seal.

    SST
    09308-10010  
    Text in Illustration 
    *1
    Oil Seal
    *2
    Oil Slinger



5. REMOVE REAR DIFFERENTIAL DRIVE PINION OIL SLINGER


C216536
  1. Remove the rear differential drive pinion oil slinger.

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt before use.



6. REMOVE REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


    F044343E01
  1. Using SST, remove the rear drive pinion tapered roller bearing (inner).

    SST
    09556-22010  

    NOTICE:
    Apply grease to the threads and tip of the SST center bolt before use.



    C216535E01
  1. Using SST, tap out the rear drive pinion tapered roller bearing (outer).

    SST
    09308-55010  



7. REMOVE DIFFERENTIAL OIL STORAGE RING


C217051
  1. Using a screwdriver and hammer, tap out the differential oil storage ring.



8. REMOVE REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


9. INSTALL REAR DIFFERENTIAL DRIVE PINION BEARING SPACER


C093595
  1. Install a new rear differential drive pinion bearing spacer.

    NOTICE:
    Install the spacer so that it is facing in the correct direction.



10. INSTALL DIFFERENTIAL OIL STORAGE RING


C216531E01
  1. Using SST and a hammer, tap in a new differential oil storage ring.

    SST
    09308-14010  

    NOTICE:
    Be careful not to damage the oil storage ring.



11. INSTALL REAR DRIVE PINION FRONT TAPERED ROLLER BEARING


C216532E01
  1. Using SST and a hammer, tap in the rear drive pinion front roller bearing (outer).

    SST
    09308-14010  

  1. Install the rear drive pinion front roller bearing (inner).



12. INSTALL FRONT DIFFERENTIAL DRIVE PINION OIL SLINGER


C216536
  1. Install the rear differential drive pinion oil slinger.



13. INSTALL REAR DIFFERENTIAL CARRIER OIL SEAL


C216533E02
  1. Apply MP grease to the lip of a new oil seal.

  1. Using SST and a hammer, tap in the rear differential carrier oil seal.

    SST
    09214-76011  

    Standard oil seal depth:
    -0.30 to 0.30 mm (-0.0118 to 0.0118 in.)

    Text in Illustration 
    *1
    Oil Seal Depth



14. INSTALL REAR DRIVE PINION COMPANION FLANGE SUB-ASSEMBLY


    C217280E01
  1. Using SST, install the rear drive pinion companion flange sub-assembly.

    SST
    09950-30012   (09951-03010, 09953-03010, 09954-03010, 09955-03030, 09956-03040)

    NOTICE:
    Before using SST (center bolt), apply hypoid gear oil to its threads and tip.



    B087843E01
  1. Using SST to hold the companion flange in place, install the rear drive pinion nut.

    SST
    09330-00021   (09330-00030)

    Torque:
    457 N*m{ 4660 kgf*cm , 337 ft.*lbf }



15. INSPECT DIFFERENTIAL DRIVE PINION PRELOAD


C089308
  1. Using a torque wrench, measure the preload.

    Standard Preload (at Starting):
    Item
    Specified Condition
    New bearing
    0.83 to 2.18 N*m (8.64 to 22.2 kgf*cm, 7.35 to 19.3 in.*lbf)
    Used bearing
    0.88 to 1.98 N*m (8.97 to 20.2 kgf*cm, 7.79 to 17.5 in.*lbf)

    If the result is not as specified, adjust the preload.

    Total preload (at starting):
    1.08 to 2.38 N*m (11.0 to 24.3 kgf*cm, 9.6 to 21.0 in.*lbf)



16. STAKE REAR DRIVE PINION NUT


C089310
  1. Using a chisel and hammer, stake the rear drive pinion nut.



17. INSTALL REAR PROPELLER SHAFT ASSEMBLY
  1. for 2WD:
    Install the rear propeller shaft assembly (Click here).

  1. for 4WD:
    Install the rear propeller shaft assembly (Click here).



18. INSTALL DIFFERENTIAL OIL
  1. Remove the differential filler plug and gasket.



    D025304E38
  1. Pour oil into the rear differential carrier assembly so that the oil level is within 0 to 5 mm (0 to 0.197 in.) of the bottom of the filler plug opening.

    NOTICE:
    Excessively large or small quantities of oil may cause problems.


    Front Differential Capacity:

    Differential Type
    Oil Type and Viscosity
    Specified Condition
    Standard
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
    1.35 to 1.45 liters (1.43 to 1.53 US qts, 1.18 to 1.27 Imp. qts.)
    w/ A.D.D. (Automatic Disconnecting Differential)
    1.50 to 1.60 liters (1.59 to 1.69 US qts, 1.32 to 1.40 Imp. qts.)


    Rear Differential Capacity:

    Differential Type
    Oil Type and Viscosity
    Specified Condition
    Standard
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
    2.65 to 2.75 liters (2.80 to 2.91 US qts, 2.33 to 2.42 Imp. qts.)
    w/ Differential Lock
    Toyota Genuine Differential gear oil LT 75W-85 GL-5 or equivalent
    2.60 to 2.70 liters (2.75 to 2.85 US qts, 2.29 to 2.38 Imp. qts.)

  1. Install a new gasket and the differential filler plug.

    Torque:
    Front differential carrier:
    39 N*m{ 398 kgf*cm , 29 ft.*lbf }
    Rear differential carrier:
    49 N*m{ 500 kgf*cm , 36 ft.*lbf }

  1. Drive the vehicle and check the oil level again.
    If necessary, add differential oil.



19. CHECK FOR DIFFERENTIAL OIL LEAKAGE