Home › Vehicle Exterior › SLIDING ROOF / CONVERTIBLE › SLIDING ROOF SYSTEM

DTC    B2343    Position Initialization Incomplete

for Preparation Click here


DESCRIPTION

This DTC is stored when the sliding roof drive gear sub-assembly (sliding roof ECU) has not been initialized.

DTC Code
DTC Detection Condition
Trouble Area
B2343
The sliding roof drive gear sub-assembly has not been initialized.
  1. Sliding roof drive gear sub-assembly (Sliding roof ECU)
  2. Map light assembly (Sliding roof switch)
  3. Harness or connector

WIRING DIAGRAM


B240414E01


INSPECTION PROCEDURE

NOTICE:
When the sliding roof drive gear sub-assembly is removed and reinstalled or replaced, the sliding roof drive gear sub-assembly must be initialized (Click here).

1.INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY
  1. Check that the sliding roof drive gear sub-assembly can be initialized (Click here).

    OK:
    The sliding roof drive gear sub-assembly can be initialized.



NG
Go to step 3
OK


2.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC B2343 is output
    B



B
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)
A

END 

3.INSPECT MAP LIGHT ASSEMBLY
E198779E02
  1. Remove the map light assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (UP) - 1 (GND)
    Tilt up switch pressed
    Below 1 Ω
    5 (UP) - 1 (GND)
    Tilt up switch not pressed
    10 kΩ or higher
    4 (DOWN) - 1 (GND)
    Tilt down switch pressed
    Below 1 Ω
    4 (DOWN) - 1 (GND)
    Tilt down switch not pressed
    10 kΩ or higher
    3 (OPN) - 1 (GND)
    Slide open switch pressed
    Below 1 Ω
    3 (OPN) - 1 (GND)
    Slide open switch not pressed
    10 kΩ or higher
    2 (CLS) - 1 (GND)
    Slide close switch pressed
    Below 1 Ω
    2 (CLS) - 1 (GND)
    Slide close switch not pressed
    10 kΩ or higher

    Text in Illustration 
    *a
    Component without harness connected
    (Map Light Assembly)



NG
REPLACE MAP LIGHT ASSEMBLY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (SLIDING ROOF ECU - SLIDING ROOF SWITCH AND BODY GROUND)
  1. Disconnect the S8 ECU connector.

  1. Disconnect the U2 map light connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    S8-10 (UP) - U2-5 (UP)
    Always
    Below 1 Ω
    S8-8 (DWN) - U2-4 (DOWN)
    Always
    Below 1 Ω
    S8-7 (OPN) - U2-3 (OPN)
    Always
    Below 1 Ω
    S8-9 (CLS) - U2-2 (CLS)
    Always
    Below 1 Ω
    U2-1 (GND) - Body ground
    Always
    Below 1 Ω
    S8-2 (E) - Body ground
    Always
    Below 1 Ω
    S8-10 (UP) or U2-5 (UP) - Body ground
    Always
    10 kΩ or higher
    S8-8 (DWN) or U2-4 (DOWN) - Body ground
    Always
    10 kΩ or higher
    S8-7 (OPN) or U2-3 (OPN) - Body ground
    Always
    10 kΩ or higher
    S8-9 (CLS) or U2-2 (CLS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (Click here)