Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1820/55    Short in Side Squib RH Circuit

DTC    B1821/55    Open in Side Squib RH Circuit

DTC    B1822/55    Short to GND in Side Squib RH Circuit

DTC    B1823/55    Short to B+ in Side Squib RH Circuit

for Preparation Click here


DESCRIPTION

The side squib RH circuit consists of the center airbag sensor and front seat side airbag RH.
This circuit instructs the SRS to deploy when deployment conditions are met.
These DTCs are stored when a malfunction is detected in the side squib RH circuit.

DTC Code
DTC Detection Condition
Trouble Area
B1820/55
One of the following conditions is met:
  1. The center airbag sensor detects a line short circuit signal 5 times in the side squib RH circuit during the primary check.
  2. A side squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Front seat side airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1821/55
One of the following conditions is met:
  1. The center airbag sensor detects an open circuit signal in the side squib RH circuit for 2 seconds.
  2. A side squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Front seat side airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1822/55
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to ground signal in the side squib RH circuit for 0.5 seconds.
  2. A side squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Front seat side airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly
B1823/55
One of the following conditions is met:
  1. The center airbag sensor detects a short circuit to B+ signal in the side squib RH circuit for 0.5 seconds.
  2. A side squib RH malfunction.
  3. A center airbag sensor malfunction.
  1. No. 2 floor wire
  2. Front seat side airbag assembly RH (Side squib RH)
  3. Center airbag sensor assembly

WIRING DIAGRAM


C174615E17


INSPECTION PROCEDURE

NOTICE:
When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).

HINT:
To perform the simulation method, enter check mode (signal check) with the Techstream (Click here), and then wiggle each connector of the airbag system or drive the vehicle on various types of road (Click here).

1.CHECK FRONT SEAT SIDE AIRBAG RH (SIDE SQUIB RH)


    C217719E06
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect the connector from the front seat side airbag RH.

  1. Connect the red wire side of SST (resistance: 2.1 Ω) to connector C.

    CAUTION:
    Never connect the tester to the front seat side airbag RH (side squib RH) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting SST.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1820, B1821, B1822 or B1823 is output

    HINT:
    Codes other than DTC B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Side Squib RH
    *2
    Center Airbag Sensor
    *3
    Connector C
    *4
    SST
    *a
    Front view of wire harness connector
    (to Side Squib RH)



NG
REPLACE FRONT SEAT SIDE AIRBAG ASSEMBLY RH (Click here)
OK


2.CHECK FLOOR WIRE (SIDE SQUIB RH CIRCUIT)


    C216072E07
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Disconnect SST from connector C.

  1. Disconnect the connectors from the center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N2-1 (SFR+) - Body ground
    Ignition switch ON
    Below 1 V
    N2-2 (SFR-) - Body ground
    Ignition switch ON
    Below 1 V

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N2-1 (SFR+) - N2-2 (SFR-)
    Always
    Below 1 Ω

  1. Release the activation prevention mechanism built into connector B (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N2-1 (SFR+) - N2-2 (SFR-)
    Always
    1 MΩ or higher
    N2-1 (SFR+) - Body ground
    Always
    1 MΩ or higher
    N2-2 (SFR-) - Body ground
    Always
    1 MΩ or higher

Text in Illustration 
*1
Side Squib RH
*2
No. 2 Floor Wire
*3
Center Airbag Sensor
*4
Connector C
*a
Front view of wire harness connector
(to Side Squib RH)


NG
REPLACE FLOOR WIRE
OK


3.CHECK CENTER AIRBAG SENSOR


    C146261E37
  1. Connect the connectors to the front seat side airbag RH and center airbag sensor.

  1. Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1820, B1821, B1822 or B1823 is not output.

    HINT:
    Codes other than DTC B1820, B1821, B1822 and B1823 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Side Squib RH
    *2
    Center Airbag Sensor



NG
REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)