DTC B1905/74 Short in Front Pretensioner Squib LH Circuit |
DTC B1906/74 Open in Front Pretensioner Squib LH Circuit |
DTC B1907/74 Short to GND in Front Pretensioner Squib LH Circuit |
DTC B1908/74 Short to B+ in Front Pretensioner Squib LH Circuit |
| DTC Code | DTC Detection Condition | Trouble Area |
| B1905/74 | One of the following conditions is met:
|
|
| B1906/74 | One of the following conditions is met:
|
|
| B1907/74 | One of the following conditions is met:
|
|
| B1908/74 | One of the following conditions is met:
|
|

| 1.CHECK FRONT SEAT OUTER BELT LH (FRONT PRETENSIONER SQUIB LH) |
![]() |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect the connectors from the front seat outer belt LH.
Connect the white wire side of SST (resistance: 2.1 Ω) to connector C.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Front Pretensioner Squib LH |
| *2 | Center Airbag Sensor |
| *3 | Connector C |
| *4 | SST |
| *a | Front view of wire harness connector (to Front Pretensioner Squib LH) |
|
| ||||
| OK | ||
| ||
| 2.CHECK CONNECTOR |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Disconnect SST from connector C.
![]() |
Check that the floor wire connector (on the front seat outer belt LH side) is not damaged.
| *1 | Front Pretensioner Squib LH |
| *2 | Center Airbag Sensor |
|
| ||||
| OK | |
| 3.CHECK NO. 2 FLOOR WIRE (FRONT PRETENSIONER SQUIB LH CIRCUIT) |
![]() |
Disconnect the connectors from the center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| O4-1 (L+) - Body ground | Ignition switch ON | Below 1 V |
| O4-2 (L-) - Body ground | Ignition switch ON | Below 1 V |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O4-1 (L+) - O4-2 (L-) | Always | Below 1 Ω |
Release the activation prevention mechanism built into connector B (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| O4-1 (L+) - O4-2 (L-) | Always | 1 MΩ or higher |
| O4-1 (L+) - Body ground | Always | 1 MΩ or higher |
| O4-2 (L-) - Body ground | Always | 1 MΩ or higher |
| *1 | Front Pretensioner Squib LH |
| *2 | No. 2 Floor Wire |
| *3 | Center Airbag Sensor |
| *4 | Connector C |
| *a | Front view of wire harness connector (to Front Pretensioner Squib LH) |
|
| ||||
| OK | |
| 4.CHECK CENTER AIRBAG SENSOR |
![]() |
Connect the connectors to the front seat outer belt LH and center airbag sensor.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
| *1 | Front Pretensioner Squib LH |
| *2 | Center Airbag Sensor |
|
| ||||
| OK | ||
| ||