Home › Vehicle Interior › HEATING / AIR CONDITIONING › AIR CONDITIONING SYSTEM (for Automatic Air Conditioning System)

DTC    B1443/43    Air Outlet Damper Control Servo Motor Circuit

for Preparation Click here


DESCRIPTION

The damper servo sub-assembly (mode damper servo) sends pulse signals to inform the air conditioning amplifier assembly of the damper position. The air conditioning amplifier assembly activates the motor (normal or reverse) based on the signals to move the air outlet damper to any position, which controls the air outlet changes.

HINT:
Confirm that no mechanical problem is present because this trouble code may be stored when either a damper link or damper is mechanically locked.


DTC Code
DTC Detection Condition
Trouble Area
B1443/43
The air outlet damper position does not change when the air conditioning amplifier assembly operates the damper servo sub-assembly (mode damper servo).
  1. Damper servo sub-assembly (mode damper servo)
  2. Air conditioning harness assembly
  3. Air conditioning amplifier assembly

WIRING DIAGRAM


E286792E01


INSPECTION PROCEDURE

1.READ VALUE USING TECHSTREAM (MODE DAMPER SERVO)
  1. Use the Data List to check if the damper servo sub-assembly (mode damper servo) is functioning properly (Click here).

    Air Conditioner 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Air Outlet Servo Pulse (D)
    Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255
    15 (pulse): FACE 1
    15 (pulse): FACE 2
    41 (pulse): B/L
    65 or 73 (pulse): FOOT
    83 or 95 (pulse): F/D
    113 (pulse): DEF
    -
    Air Outlet Servo Actu Pulse (D)
    Damper servo sub-assembly (mode damper servo) actual pulse / Min.: 0, Max.: 255
    15 (pulse): FACE 1
    15 (pulse): FACE 2
    41 (pulse): B/L
    65 or 73 (pulse): FOOT
    83 or 95 (pulse): F/D
    113 (pulse): DEF
    -

    OK:
    The display is as specified in the normal condition column.

    Result 
    Result
    Proceed to
    OK (When troubleshooting according to problem symptoms table)
    A
    OK (When troubleshooting according to the DTC)
    B
    NG
    C



B
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

C
Go to step 2
A

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

2.PERFORM ACTIVE TEST USING TECHSTREAM (MODE DAMPER SERVO)
  1. Select the Active Test, use the Techstream to generate a control command, and then check that the damper servo sub-assembly (mode damper servo) operates (Click here).

    Air Conditioner 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Air Outlet Servo Pulse (D)
    Damper servo sub-assembly (mode damper servo) pulse
    Min.: 0, Max.: 255
    -

    OK:
    Damper servo sub-assembly (mode damper servo) operates normally.



NG
Go to step 3
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)  

3.REPLACE DAMPER SERVO SUB-ASSEMBLY (MODE DAMPER SERVO)
  1. Replace the damper servo sub-assembly (mode damper servo) (Click here).

    HINT:
    Since the damper servo sub-assembly (mode damper servo) cannot be inspected while it is removed from the vehicle, replace the damper servo sub-assembly (mode damper servo) with a new or normally functioning one.


NEXT


4.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1443 is not output.



NG
Go to step 5
OK

END (DAMPER SERVO SUB-ASSEMBLY [MODE DAMPER SERVO] IS FAULTY) 

5.REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY
  1. Temporarily replace the air conditioning amplifier assembly with a new or normally functioning one (Click here).


NEXT


6.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B1443 is not output.



NG
REPLACE AIR CONDITIONING HARNESS ASSEMBLY (Click here)
OK

END (AIR CONDITIONING AMPLIFIER ASSEMBLY IS FAULTY)