Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENGINE IMMOBILISER SYSTEM (w/o Smart Key System)

DTC    B279A    Theft Deterrent System Communication Line High Fixation

for Preparation Click here


DESCRIPTION

If the communication line (EFIO-IMI) to the transponder key ECU assembly is stuck on HI output, the ECM stores this DTC.

DTC Code
DTC Detection Condition
Trouble Area
B279A
The communication line (EFIO-IMI) between the ECM and transponder key ECU assembly is stuck on HI output for 6 seconds or more.
  1. Harness or connector
  2. Transponder key ECU assembly
  3. ECM

WIRING DIAGRAM


B295355E01


INSPECTION PROCEDURE

NOTICE:
  1. When the transponder key ECU assembly and/or ECM is replaced, refer to Registration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2.CHECK FOR DTC
  1. Check for DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B279A is output
    A
    DTC B279A and other DTCs are output
    B

    HINT:
    If any DTCs other than B279A are output, troubleshoot those DTCs first.



B
GO TO DIAGNOSTIC TROUBLE CODE CHART (Click here)
A


3.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - ECM)
  1. Disconnect the F34 ECU connector.

  1. Disconnect the F50 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F34-13 (EFIO) - F50-14 (IMI)
    Always
    Below 1 Ω
    F34-13 (EFIO) or F50-14 (IMI) - Body ground
    Always
    10 kΩ or higher

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F34-13 (EFIO) - Body ground
    Always
    Below 1 V
    F50-14 (IMI) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK TRANSPONDER KEY ECU ASSEMBLY (OUTPUT)


  1. Using an oscilloscope, check the waveform.


    B242189E06


    Text in Illustration 
    *a
    Component with harness connected
    (ECM)
    -
    -
    Measurement Condition 
    Item
    Content
    Tester Connection
    F50-14 (IMI) - Body ground
    Tool Setting
    10 V/DIV., 100 ms./DIV.
    Condition
    Ignition switch ON

    OK:
    Waveform is output normally (refer to illustration).



NG
Go to step 5
OK

REPLACE ECM (Click here)  

5.CHECK HARNESS AND CONNECTOR (TRANSPONDER KEY ECU - BATTERY AND BODY GROUND)


    B242622E02
  1. Disconnect the F34 ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F34-1 (+B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F34-16 (GND) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Transponder Key ECU Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.REPLACE TRANSPONDER KEY ECU ASSEMBLY
  1. Replace the transponder key ECU assembly (Click here).


NEXT


7.REGISTER ECU - ECM COMMUNICATION ID
  1. Register the ECU - ECM communication ID (Click here).


NEXT


8.CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


9.CHECK FOR DTC
  1. Check for DTCs (Click here).

    OK:
    DTC B279A is not output.



NG
REPLACE ECM (Click here)
OK

END (TRANSPONDER KEY ECU IS DEFECTIVE)