DTC C1415 Rear Speed Sensor RH Output Malfunction |
DTC C1277 Abnormal Change in Output Signal of Rear Speed Sensor RH (Test Mode DTC) |
DTC C1278 Abnormal Change in Output Signal of Rear Speed Sensor LH (Test Mode DTC) |
DTC C1416 Rear Speed Sensor LH Output Malfunction |
| DTC Code | DTC Detection Condition | Trouble Area |
| C1415 C1416 | One of the following conditions is met:
|
|
| C1277 C1278 | Stored only during test mode. |
|
| 1.CHECK HARNESS AND CONNECTOR (MOMENTARY INTERRUPTION) |
Using the Techstream, check for any momentary interruption in the wire harness and connector corresponding to the DTC (Click here).
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Speed Open | Rear speed sensor RH open detection/ Error or Normal | Normal | - |
| RL Speed Open | Rear speed sensor LH open detection/ Error or Normal | Normal | - |
|
| ||||
| OK | |
| 2.READ VALUE USING TECHSTREAM (REAR SPEED SENSOR) |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Start the engine.
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| RR Wheel Speed | Rear speed sensor RH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
| RL Wheel Speed | Rear speed sensor LH reading/ Min.: 0 km/h (0 mph), Max.: 326 km/h (202 mph) | Actual wheel speed | No large fluctuations when driving at a constant speed. |
Check that there is no difference between the speed value output from the speed sensor displayed on the Techstream and the speed value displayed on the speedometer when driving the vehicle.
|
| ||||
| OK | |
| 3.PERFORM TEST MODE (SIGNAL CHECK) |
Perform the signal check in the Test Mode Procedure (Click here).
|
| ||||
| OK | |
| 4.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1415 and C1416 are not output | A |
| DTCs C1415 and/or C1416 are output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK REAR SPEED SENSOR INSTALLATION |
Turn the ignition switch off.
![]() |
Check the speed sensor installation.
| *1 | Rear Speed Sensor |
| *a | No clearance |
| *b | OK |
| *c | NG |
|
| ||||
| OK | |
| 6.INSPECT REAR SPEED SENSOR TIP |
|
| ||||
| OK | |
| 7.INSPECT REAR SPEED SENSOR ROTOR |
Remove the rear axle hub and bearing assembly (Click here).
Check the speed sensor rotor.
|
| ||||
| OK | |
| 8.INSPECT SKID CONTROL SENSOR WIRE |

| *A | for RH | *B | for LH |
| *1 | Skid Control Sensor Wire | - | - |
Remove the skid control sensor wire (Click here).
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| Qz1-4 - z7-2 (RR+) | Always | Below 1 Ω |
| Qz1-3 - z7-1 (RR-) | Always | Below 1 Ω |
| Qz1-4 - Qz1-3 | Always | 10 kΩ or higher |
| Qz1-4 - Qz1-1 | Always | 10 kΩ or higher |
| Qz1-4 - Qz1-2 | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| Qz1-2 - z8-2 (RL+) | Always | Below 1 Ω |
| Qz1-1 - z8-1 (RL-) | Always | Below 1 Ω |
| Qz1-2 - Qz1-1 | Always | 10 kΩ or higher |
| Qz1-2 - Qz1-3 | Always | 10 kΩ or higher |
| Qz1-2 - Qz1-4 | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 9.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - REAR SPEED SENSOR) |
Install the skid control sensor wire.
Disconnect the A6 skid control ECU connector.
Disconnect the z7 and/or z8 rear speed sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A6-5 (RR+) - z7-2 (RR+) | Always | Below 1 Ω |
| A6-5 (RR+) - Body ground | Always | 10 kΩ or higher |
| A6-19 (RR-) - z7-1 (RR-) | Always | Below 1 Ω |
| A6-19 (RR-) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| A6-20 (RL+) - z8-2 (RL+) | Always | Below 1 Ω |
| A6-20 (RL+) - Body ground | Always | 10 kΩ or higher |
| A6-6 (RL-) - z8-1 (RL-) | Always | Below 1 Ω |
| A6-6 (RL-) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 10.CHECK TERMINAL VOLTAGE (RR+, RL+) |
Disconnect the z7 and/or z8 rear speed sensor connector.
Connect the A6 skid control ECU connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| z7-2 (RR+) - Body ground | Ignition switch ON | 11 to 14 V |
| Tester Connection | Switch Condition | Specified Condition |
| z8-2 (RL+) - Body ground | Ignition switch ON | 11 to 14 V |
| *A | for RH |
| *B | for LH |
| *a | Front view of wire harness connector (to Rear Speed Sensor) |
|
| ||||
| OK | |
| 11.RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1415 and C1416 are not output | A |
| DTCs C1415 and/or C1416 are output | B |
|
| ||||
| A | ||
| ||
| 12.REPLACE REAR SPEED SENSOR |
Replace the rear speed sensor (Click here).
| NEXT | |
| 13.RECONFIRM DTC |
Turn the ignition switch off.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle at a speed of 40 km/h (25 mph) or more for at least 60 seconds.
Check if the same DTC is output (Click here).
| Result | Proceed to |
| DTCs C1415 and C1416 are not output | A |
| DTCs C1415 and/or C1416 are output | B |
|
| ||||
| A | ||
| ||