Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0017    Crankshaft Position - Camshaft Position Correlation (Bank 1 Sensor B)

DTC    P0019    Crankshaft Position - Camshaft Position Correlation (Bank 2 Sensor B)

for Preparation Click here


DESCRIPTION

Refer to DTC P0335 (Click here).

DTC No.
DTC Detection Condition
Trouble Area
P0017
Deviations in the crankshaft position sensor and VVT sensor 1 (for exhaust camshaft) signals (2 trip detection logic).
  1. Valve timing
  2. Camshaft timing oil control valve for exhaust camshaft
  3. Oil control valve filter
  4. Camshaft timing exhaust gear assembly
  5. ECM
P0019
Deviations in the crankshaft position sensor and VVT sensor 2 (for exhaust camshaft) signals (2 trip detection logic).

MONITOR DESCRIPTION

The ECM checks valve timing (VVT learned value) on the exhaust side while the engine is running at a low speed in order to monitor the gap between the current and target valve timing on the exhaust side. The VVT learned value is calculated from the positions of the camshaft and crankshaft. The camshaft will come to the most retarded position when the engine is running at a low speed. If the camshaft position is normal, the VVT learned value should be within the specified range. If the VVT learned value is not within the specified range, the ECM determines this to be a malfunction.

MONITOR STRATEGY


Related DTCs
Deviation in crankshaft position sensor signal and camshaft position sensor signal (Bank 2 Sensor 2)
Required Sensors/Components (Main)
Timing chain/belt
Required Sensors/Components (Related)
None
Frequency of Operation
Once per driving cycle
Duration
Less than 60 seconds
MIL Operation
2 driving cycles
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


All 
The monitor will run whenever these DTCs are not present
P0013, P0023 (Exhaust VVT Oil Control Valve)
P0017, P0019 (Exhaust VVT System - Misalignment)
P0102, P0103 (Mass Air Flow Sensor)
P0115, P0117, P0118 (Engine Coolant Temperature Sensor)
P0125 (Insufficient Coolant Temperature for Closed Loop Fuel Control)
P0335 (Crankshaft Position Sensor)
P0340 (Camshaft Position Sensor)
Engine speed
500 to 1000 rpm

TYPICAL MALFUNCTION THRESHOLDS


One of following conditions is met
-
VVT learning value at maximum advanced valve timing (Bank 1)
Less than 81.1°CA (crankshaft angle)
VVT learning value at maximum advanced valve timing (Bank 2)
Less than 81.1°CA (crankshaft angle)
VVT learning value at maximum advanced valve timing (Bank 1)
More than 105.9°CA (crankshaft angle)
VVT learning value at maximum advanced valve timing (Bank 2)
More than 105.9°CA (crankshaft angle)

CONFIRMATION DRIVING PATTERN


A197314E01

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear the DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine and warm it up until the ECT reaches 75°C (167°F) or higher [B].
  7. Idle the engine for 5 minutes or more [C].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [D].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0017 or P0019.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [E] through [G].

  13. Drive the vehicle for 2 to 3 minutes [E].

    CAUTION:
    When performing the confirmation driving pattern, obey all speed limits and traffic laws.

  14. Idle the engine for 5 minutes or more [F].
  15. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [G].
  16. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  17. Check the DTC judgment result.
  18. If the test result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to DTC P0335 (Click here).

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P0017 AND P0019)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read the DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    P0017 or P0019
    A
    P0017 or P0019 and other DTCs
    B

    HINT:
    If any DTCs other than P0017 or P0019 are output, troubleshoot those DTCs first.



B
GO TO DTC CHART (Click here)
A


2.PERFORM ACTIVE TEST USING TECHSTREAM (OPERATE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY FOR EXHAUST CAMSHAFT)
  1. Connect the Techstream to the DLC3.

  1. Start the engine and turn the Techstream on.

  1. Turn the A/C switch on.

  1. Warm up the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the VVT Exhaust Linear (Bank 1) or Control the VVT Exhaust Linear (Bank 2).

  1. Check the engine speed while operating the camshaft timing oil control valve using the Techstream.

    OK:

    Tester Operation
    Specified Condition
    0% (OFF)
    Normal engine idle speed
    127% (ON)
    Engine idles roughly or stalls
    (soon after camshaft timing oil control valve switched from OFF to ON)

    HINT:
    Refer to "Data List / Active Test" [VVT OCV Duty #1, VVT Change Angle #1] (Click here).



NG
Go to step 4
OK


3.CHECK WHETHER DTC OUTPUT RECURS (DTC P0017 OR P0019)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the Techstream (Click here).

  1. Drive the vehicle for more than 10 minutes.

  1. Read the DTCs using the Techstream.

    OK:
    No DTC output.



NG
Go to step 4
OK

END 

4.CHECK VALVE TIMING (CHECK FOR LOOSE TEETH AND WHETHER TIMING CHAIN HAS JUMPED TOOTH)


    A103826E11
  1. Remove the cylinder head cover RH and LH.
    Text in Illustration 
    *1
    Timing Mark

  1. Turn the crankshaft pulley and align its groove with the "0" timing mark on the timing chain cover.

  1. Check that the timing marks on the camshaft timing gears are aligned with the timing marks of the bearing cap as shown in the illustration.

    1. If not, turn the crankshaft 1 revolution (360°), and then align the marks as above.

    OK:
    Timing marks on camshaft timing gears are aligned as shown in the illustration.

  1. Reinstall the cylinder head cover RH and LH.



NG
ADJUST VALVE TIMING (Click here)
OK


5.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (FOR EXHAUST CAMSHAFT)
  1. Inspect the camshaft timing oil control valve (Click here).



NG
REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY (Click here)
OK


6.CHECK OIL CONTROL VALVE FILTER AND PIPE
A225778E01
  1. Remove the oil pipe No. 1 or No. 2.
    Text in Illustration 
    *1
    No. 1 Oil Pipe
    *2
    No. 2 Oil Pipe

  1. Remove the oil control valve filter.

  1. Check that the filter and pipe are not clogged.

    OK:
    The filter and pipe are not clogged.

  1. Reinstall the oil control valve filter.

  1. Reinstall the oil pipe No. 1 or No. 2.



NG
REPLACE OIL CONTROL VALVE FILTER OR PIPE
OK


7.REPLACE CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY
  1. Replace the camshaft timing exhaust gear assembly (Click here).


NEXT


8.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and turn the Techstream on.

  1. Clear the DTCs (Click here).

  1. Start the engine and warm it up.

  1. Switch the ECM from normal mode to check mode using the Techstream (Click here).

  1. Drive the vehicle for more than 10 minutes.

  1. Confirm that no DTC is output using the Techstream.

    OK:
    No DTC output.

    HINT:
    DTC P0017 or P0019 is stored when foreign objects in the engine oil are caught in some parts of the system. These codes will remain stored even if the system returns to normal after a short time. These foreign objects are then captured by the oil filter, thus eliminating the source of the problem.



NG
REPLACE ECM (Click here)
OK

END