Home › Engine / Hybrid System › 1GR-FE ENGINE CONTROL › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

DTC    P0339    Crankshaft Position Sensor "A" Circuit Intermittent

for Preparation Click here


DESCRIPTION

The crankshaft position sensor system consists of a crankshaft position sensor plate and pickup coil.
The sensor plate has 34 teeth and is installed on the crankshaft. The pickup coil is made of wound copper wire, an iron core and magnet. The sensor plate rotates and, as each tooth passes by the pickup coil, a pulse signal is created. The pickup coil generates 34 signals per crankshaft revolution. Based on these signals, the ECM calculates the crankshaft position and engine speed. Using these calculations, the fuel injection time and ignition timing are controlled.

DTC No.
DTC Detection Condition
Trouble Area
P0335
Either condition is met:
  1. No crankshaft position sensor signal is sent to the ECM while cranking (1 trip detection logic).
  2. No crankshaft position sensor signal is sent to the ECM at an engine speed of 600 rpm or more (1 trip detection logic).
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft position sensor plate
  4. ECM
P0339
Under conditions (a), (b) and (c), no crankshaft position sensor signal is sent to the ECM for 0.05 seconds or more (1 trip detection logic):
(a) Engine speed is 1000 rpm or more.
(b) Starter signal is off.
(c) 3 seconds or more have elapsed since the starter signal switched from on to off.
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. Crankshaft position sensor plate
  4. ECM

  1. A122767E04
    Reference: Inspection using an oscilloscope (VV1, VV2 and NE Signal Waveforms).

    HINT:
    1. The correct waveforms are as shown.
    2. VV1+ and VV2+ are the VVT sensor signals, and NE+ is the crankshaft position sensor signal.
    3. Grounding failure of the shielded wire may cause noise in the waveforms.

    Item
    Content
    Terminal
    VV1+ - VV1-
    VV2+ - VV2-
    NE+ - NE-
    Equipment Setting
    5 V/DIV.,
    20 msec./DIV.
    Condition
    Cranking or idling

MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor.
If the malfunction is not repaired successfully, a DTC is stored 10 seconds after the engine is next started.

MONITOR STRATEGY


Related DTCs
P0335: Crankshaft position sensor range check or rationality
Required Sensors/Components (Main)
Crankshaft position sensor
Required Sensors/Components (Related)
VVT sensor
Frequency of Operation
Continuous
Duration
4.7 seconds
MIL Operation
Immediate
Sequence of Operation
None

TYPICAL ENABLING CONDITIONS


Case 1 
Monitor runs whenever following DTCs not present
P0340, P0342, P0343 (VVT Sensor)
Time after starter OFF to ON
3 seconds or more
Number of VVT sensor signal pulses
6
Battery voltage
7 V or higher
Minimum battery voltage while starter ON
Below 11 V

Case 2 
Monitor runs whenever following DTCs not present
None
Starter
OFF
Engine speed
600 rpm or more
Time after starter from ON to OFF
3 seconds or more

Case 3 
Monitor runs whenever following DTCs not present
None
Starter
ON
Minimum battery voltage while starter ON
Below 11 V

TYPICAL MALFUNCTION THRESHOLDS


Case 1 
Number of crankshaft position sensor signal pulses
132 or less, and 174 or more

Case 2, Case 3 
Engine speed signal
No signal

COMPONENT OPERATING RANGE


Crankshaft position sensor
  1. Crankshaft position sensor output voltage fluctuates while crankshaft revolving
  2. 34 crankshaft position sensor signals per crankshaft revolution

CONFIRMATION DRIVING PATTERN


A198821E05

  1. Connect the Techstream to the DLC3.
  2. Turn the ignition switch to ON and turn the Techstream on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the Techstream on [A].
  6. Start the engine.
  7. Idle the engine for 20 seconds or more [B].
  8. Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].
  9. Read the pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.
  11. Input the DTC: P0335 or P0339.
  12. Check the DTC judgment result.

    Tester Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.
    3. If the judgment result shows INCOMPLETE or N/A, perform steps [B] and [C] again.

  13. If no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A227123E03


INSPECTION PROCEDURE

HINT:
  1. After performing the inspection procedure for the crankshaft position sensor, if DTC P0335 is output again, check the following items related to the camshaft position sensor.
    1. Installation condition of the camshaft position sensor.
    2. Installation condition of the camshaft.
    3. Connection of the camshaft position sensor connector.
  2. If no problem is found through this diagnostic troubleshooting procedure, troubleshoot the engine mechanical system.
  3. Check the engine speed. The engine speed can be checked by using the Techstream. To check the engine speed, follow the procedure below:
    1. Connect the Techstream to the DLC3.
    2. Start the engine.
    3. Turn the Techstream on.
    4. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.
    1. The engine speed may be indicated as zero despite the crankshaft revolving normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
  4. Read freeze frame data using the Techstream. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING TECHSTREAM (ENGINE SPEED)
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Engine Speed.

  1. Start the engine.

  1. Read the values displayed on the Techstream while the engine is running.

    OK:
    Correct values are displayed.

    HINT:
    1. To check the engine speed change, display the graph on the Techstream.
    2. If the engine does not start, check the engine speed while cranking.
    3. If the engine speed indicated on the Techstream remains at zero (0), there may be an open or short in the crankshaft position sensor circuit.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.INSPECT CRANKSHAFT POSITION SENSOR (RESISTANCE)
  1. Inspect the crankshaft position sensor .



NG
REPLACE CRANKSHAFT POSITION SENSOR (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (CRANKSHAFT POSITION SENSOR - ECM)
  1. Disconnect the crankshaft position sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B14-1 - B36-6 (NE+)
    Always
    Below 1 Ω
    B14-2 - B36-5 (NE-)
    Always
    Below 1 Ω
    B14-1 or B36-6 (NE+) - Body ground
    Always
    10 kΩ or higher
    B14-2 or B36-5 (NE-) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connector.

  1. Reconnect the crankshaft position sensor connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
BR03795E25
  1. Check the crankshaft position sensor installation.

    OK:
    Sensor is installed correctly.



NG
SECURELY REINSTALL SENSOR (Click here)
OK


5.CHECK CRANKSHAFT POSITION SENSOR PLATE (TEETH OF SENSOR PLATE)
  1. Check the teeth of the sensor plate.

    OK:
    Sensor plate teeth do not have any cracks or deformation.



NG
REPLACE CRANKSHAFT (Click here)
OK


6.REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the Techstream on.

  1. Clear DTCs (Click here).

  1. Start the engine.

  1. Enter the following menus: Powertrain / Engine and ECT / Trouble Code.

  1. Read DTCs.

    Result 
    Display (DTC Output)
    Proceed to
    No output
    A
    P0335 or P0339
    B

HINT:
If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END