Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

DTC    B2650    Slide Sensor Malfunction

for Preparation Click here


DESCRIPTION

When the front power seat switch LH does not receive a sensor signal despite forward or backward movement of the seat by power seat motor operation, this DTC is stored.

DTC Code
DTC Detection Condition
Trouble Area
B2650
The forward and backward lock detection position of the sensor is the same.
  1. Front power seat switch LH
  2. Separate type front seat cushion spring assembly LH (Slide motor)
  3. Harness or connector

WIRING DIAGRAM


B357484E01


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (POWER SEAT MOTOR FUNCTION)
  1. Select the Active Test, use the Techstream to generate a control command, and then check the power seat motor function (Click here).

    Driver Seat 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Seat Slide Operation
    Seat sliding operation
    Front / OFF / Rear
    -

    OK:
    Motor operates normally.



NG
Go to step 5
OK


2.CHECK FRONT POWER SEAT SWITCH LH (SLIDE MOTOR CIRCUIT)


    B238255E21
  1. Disconnect the b15 slide motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b15-2 (O/P) - b15-3 (GND)
    Sliding switch on
    4.8 to 5.1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Separate Type Front Seat Cushion Spring Assembly LH [Slide Motor])



NG
Go to step 4
OK


3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (SLIDE MOTOR)


    B355245E01
  1. Connect the b15 slide motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b15-2 (O/P) - Body ground
    Sliding switch on
    4.5 to 4.8 V

    Text in Illustration 
    *a
    Component with harness connected
    (Separate Type Front Seat Cushion Spring Assembly LH [Slide Motor])



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (SLIDE MOTOR) (Click here)
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)  

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - SLIDE MOTOR)
  1. Disconnect the b19 front power seat switch LH connector.

  1. Disconnect the b15 slide motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    b19-5 (SSRS) - b15-2 (O/P)
    Always
    Below 1 Ω
    b19-1 (SGND) - b15-3 (GND)
    Always
    Below 1 Ω
    b19-5 (SSRS) - Body ground
    Always
    10 kΩ or higher
    b19-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)  

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (SLIDE MOTOR)


    B238714E30
  1. Remove the separate type front seat cushion spring assembly LH (slide motor) (Click here).

  1. Disconnect the b15 slide motor connector.

  1. Check if the seat cushion spring moves smoothly when the battery is connected to the slide motor connector terminals.

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 4 (FWD)
    Battery negative (-) → 1 (BACK)
    Front seat cushion spring assembly LH moves forward
    Battery positive (+) → 1 (BACK)
    Battery negative (-) → 4 (FWD)
    Front seat cushion spring assembly LH moves backward

    Text in Illustration 
    *a
    Component without harness connected
    (Separate Type Front Seat Cushion Spring Assembly LH [Slide Motor])



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (SLIDE MOTOR) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - SLIDE MOTOR)
  1. Disconnect the b18 front power seat switch LH connector.

  1. Disconnect the b15 slide motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    b18-3 (SLD+) - b15-4 (FWD)
    Always
    Below 1 Ω
    b18-4 (SLD-) - b15-1 (BACK)
    Always
    Below 1 Ω
    b18-3 (SLD+) - Body ground
    Always
    10 kΩ or higher
    b18-4 (SLD-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)