Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

DTC    B2651    Reclining Sensor Malfunction

for Preparation Click here


DESCRIPTION

When the front power seat switch LH does not receive a sensor signal despite forward or backward movement of the seatback by power seat motor operation, this DTC is stored.

DTC Code
DTC Detection Condition
Trouble Area
B2651
The forward and backward lock detection position of the sensor is the same.
  1. Front power seat switch LH
  2. Separate type front seatback spring assembly LH (Reclining motor)
  3. Harness or connector

WIRING DIAGRAM


B357484E02


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (POWER SEAT MOTOR FUNCTION)
  1. Select the Active Test, use the Techstream to generate a control command, and then check the power seat motor function (Click here).

    Driver Seat 
    Tester Display
    Test Part
    Control Ranger
    Diagnostic Note
    Seat Reclining
    Seat reclining operation
    Front / OFF / Rear
    -

    OK:
    Motor operates normally.



NG
Go to step 5
OK


2.CHECK FRONT POWER SEAT SWITCH LH (RECLINING MOTOR CIRCUIT)


    B238255E22
  1. Disconnect the d5 reclining motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    d5-2 (O/P) - d5-3 (GND)
    Reclining switch on
    4.8 to 5.1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Separate Type Front Seatback Spring Assembly LH [Reclining Motor])



NG
Go to step 4
OK


3.CHECK SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH (RECLINING MOTOR)


    B355245E02
  1. Connect the d5 reclining motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    d5-2 (O/P) - Body ground
    Reclining switch on
    4.5 to 4.8 V

    Text in Illustration 
    *a
    Component with harness connected
    (Separate Type Front Seatback Spring Assembly LH [Reclining Motor])



NG
REPLACE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH (RECLINING MOTOR) (Click here)
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)  

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH - RECLINING MOTOR)
  1. Disconnect the b19 front power seat switch LH connector.

  1. Disconnect the d5 reclining motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    b19-11 (SSRR) - d5-2 (O/P)
    Always
    Below 1 Ω
    b19-1 (SGND) - d5-3 (GND)
    Always
    Below 1 Ω
    b19-11 (SSRR) - Body ground
    Always
    10 kΩ or higher
    b19-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)  

5.INSPECT SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH (RECLINING MOTOR)


    B238256E16
  1. Remove the front seatback board sub-assembly .

  1. Disconnect the b5 reclining motor connector.

  1. Check if the seatback moves smoothly when the battery is connected to the reclining motor connector terminals.

    OK:
    Measurement Condition
    Operational Direction
    Battery positive (+) → 1 (FWD)
    Battery negative (-) → 4 (BACK)
    Seatback moves forward
    Battery positive (+) → 4 (BACK)
    Battery negative (-) → 1 (FWD)
    Seatback moves backward

    Text in Illustration 
    *a
    Component without harness connected
    (Separate Type Front Seatback Spring Assembly LH [Reclining Motor])



NG
REPLACE SEPARATE TYPE FRONT SEATBACK SPRING ASSEMBLY LH (RECLINING MOTOR) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - RECLINING MOTOR)
  1. Disconnect the b18 front power seat switch LH connector.

  1. Disconnect the d5 reclining motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    b18-9 (RCL+) - d5-1 (FWD)
    Always
    Below 1 Ω
    b18-11 (RCL-) - d5-4 (BACK)
    Always
    Below 1 Ω
    b18-9 (RCL+) - Body ground
    Always
    10 kΩ or higher
    b18-11 (RCL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)