Home › Vehicle Interior › SEAT › FRONT POWER SEAT CONTROL SYSTEM (w/ Memory)

DTC    B2652    Front Vertical Sensor Malfunction

for Preparation Click here


DESCRIPTION

When the front power seat switch LH does not receive a sensor signal despite upward or downward movement of the front of the seat cushion by power seat motor operation, this DTC is stored.

DTC Code
DTC Detection Condition
Trouble Area
B2652
The upward and downward lock detection position of the sensor is the same.
  1. Front power seat switch LH
  2. Separate type front seat cushion Spring assembly LH (Front vertical motor)
  3. Harness or connector

WIRING DIAGRAM


B357484E03


INSPECTION PROCEDURE

1.PERFORM ACTIVE TEST USING TECHSTREAM (POWER SEAT MOTOR FUNCTION)
  1. Select the Active Test, use the Techstream to generate a control command, and then check the power seat motor function (Click here).

    Driver Seat 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Front Vertical Operation
    Seat front vertical operation
    Up / OFF / Down
    -

    OK:
    Motor operates normally.



NG
Go to step 5
OK


2.CHECK FRONT POWER SEAT SWITCH LH (FRONT VERTICAL MOTOR CIRCUIT)


    B238255E23
  1. Disconnect the b16 front vertical motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b16-2 (O/P) - b16-3 (GND)
    Front vertical switch on
    4.8 to 5.1 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Separate Type Front Seat Cushion Spring Assembly LH [Front Vertical Motor])



NG
Go to step 4
OK


3.CHECK SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (FRONT VERTICAL MOTOR)


    B355245E03
  1. Connect the b16 front vertical motor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    b16-2 (O/P) - Body ground
    Front vertical switch on
    4.5 to 4.8 V

    Text in Illustration 
    *a
    Component with harness connected
    (Separate Type Front Seat Cushion Spring Assembly LH [Front Vertical Motor])



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (FRONT VERTICAL MOTOR) (Click here)
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)  

4.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - FRONT VERTICAL MOTOR)
  1. Disconnect the b19 front power seat switch LH connector.

  1. Disconnect the b16 front vertical motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    b19-3 (SSFV) - b16-2 (O/P)
    Always
    Below 1 Ω
    b19-1 (SGND) - b16-3 (GND)
    Always
    Below 1 Ω
    b19-3 (SSFV) - Body ground
    Always
    10 kΩ or higher
    b19-1 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)  

5.INSPECT SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (FRONT VERTICAL MOTOR)


    B238256E17
  1. Remove the separate type front seat cushion spring assembly LH (front vertical motor) (Click here).

  1. Disconnect the b16 front vertical motor.

  1. Check if the seat cushion spring moves smoothly when the battery is connected to the front vertical motor connector terminals.

    OK:
    Measurement Condition
    Operational Direction
    Battery positive (+) → 4 (UP)
    Battery negative (-) → 1 (DOWN)
    Seat cushion spring moves upward
    Battery positive (+) → 1 (DOWN)
    Battery negative (-) → 4 (UP)
    Seat cushion spring moves downward

    Text in Illustration 
    *a
    Component without harness connected
    (Separate Type Front Seat Cushion Spring Assembly LH [Front Vertical Motor])



NG
REPLACE SEPARATE TYPE FRONT SEAT CUSHION SPRING ASSEMBLY LH (FRONT VERTICAL MOTOR) (Click here)
OK


6.CHECK HARNESS AND CONNECTOR (FRONT POWER SEAT SWITCH LH - FRONT VERTICAL MOTOR)
  1. Disconnect the b18 front power seat switch LH connector.

  1. Disconnect the b16 front vertical motor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    b18-8 (FRV+) - b16-4 (UP)
    Always
    Below 1 Ω
    b18-5 (FRV-) - b16-1 (DOWN)
    Always
    Below 1 Ω
    b18-8 (FRV+) - Body ground
    Always
    10 kΩ or higher
    b18-5 (FRV-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE FRONT POWER SEAT SWITCH LH (Click here)