Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Start Function)

SMART KEY SYSTEM (for Start Function) > Power Source Mode does not Change to ON (IG and ACC)

for Preparation Click here


DESCRIPTION

When the engine switch is pushed with the key in the cabin, the power management control receives signals to switch the power source mode.

WIRING DIAGRAM


C217209E02


INSPECTION PROCEDURE

NOTICE:
  1. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the vehicle and turn a courtesy light switch on and off at 1.5 second intervals until communication between the Techstream and vehicle begins.
  2. Before performing the inspection, check that there are no problems related to the CAN communication system and LIN communication system.
  3. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK HARNESS AND CONNECTOR (BATTERY - POWER MANAGEMENT CONTROL ECU)


    A207890E08
  1. Disconnect the F80 power management control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F80-2 (AM21) - Body ground
    Always
    9.5 to 14 V
    F80-1 (AM22) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - BODY GROUND)
  1. Disconnect the F80 power management control ECU connector.



    A207890E09
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F80-6 (GND) - Body ground
    Always
    Below 1 Ω
    F80-5 (GND2) - Body ground

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Management Control ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.READ VALUE USING TECHSTREAM (KEY CERTIFI WAIT T-OUT)
  1. Connect the Techstream to the DLC3.

  1. Turn the Techstream on.

    HINT:
    When using the Techstream with the engine switch off, turn any of the door courtesy light switches on and off repeatedly at intervals of 1.5 seconds or less until communication between the tester and vehicle starts.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. Read the Data List and check that "No" is displayed 1 second after turning the engine switch from off to on (IG).

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Key Certifi Wait T-Out
    Key certification waiting timed out / Yes or No
    Yes: Key certification waiting timed out
    No: Key certification completed within specified time
    -

    OK:
    "No" is displayed 1 second after turning the engine switch from off to on (IG).



NG
Go to step 9
OK


4.READ VALUE USING TECHSTREAM (START SWITCH 1, 2)
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. According to the display on the Techstream, read the Data List.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Start Switch1
    Start Switch 1 / ON or OFF
    ON: Engine switch pushed
    OFF: Engine switch not pushed
    -
    Start Switch2
    Start Switch 2 / ON or OFF
    ON: Engine switch pushed
    OFF: Engine switch not pushed
    -

    OK:
    The display changes in response to the operation of the engine switch.



NG
Go to step 7
OK


5.CHECK POWER MANAGEMENT CONTROL ECU
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Power Source Control / Data List.

  1. Read the Data List and check that the display changes according to the changes in the power source mode when the engine switch is pushed.

    Power Source Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Power Supply Condition
    Power Supply Condition / IG2 ON, ST ON, All OFF, IG1 ON or ACC ON
    IG2 ON: IG2 relay on
    ST ON: ST request signal on
    All OFF: All relays off
    IG1 ON: IG1 relay on
    ACC ON: ACC relay on
    -

    OK:
    Display changes according to the changes in the power source mode when the engine switch is pushed.



  1. Measure the voltage according to the value(s) in the table below.


    C182533E24


    Text in Illustration 
    *a
    Component with harness connected
    (Power Management Control ECU)
    -
    -

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F80-20 (IG1D) - Body ground
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    Engine switch on (IG)
    ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
    F81-8 (IG2D) - Body ground
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    Engine switch on (IG)
    ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
    F80-19 (ACCD) - Body ground
    Engine switch off
    Below 1 V
    Engine switch on (ACC)
    ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher
    Engine switch on (IG)
    ((Voltage at terminal AM21 or AM22) minus 2.0 V) or higher



NG
REPLACE POWER MANAGEMENT CONTROL ECU (Click here)
OK


6.CONFIRMATION TEST
  1. Check that the power source mode changes to on (ACC) and on (IG) when operating the engine switch.

    OK:
    The power source mode changes to on (ACC) and on (IG) in response to the operation of the engine switch.



NG
CHECK RELAY CONTACT SIDE CIRCUIT
OK

USE SIMULATION METHOD TO CHECK (Click here)  

7.INSPECT ENGINE SWITCH


    A207999E02
  1. Remove the engine switch.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    7 (SS1) - 5 (GND)
    Engine switch not pushed
    10 kΩ or higher
    Engine switch pushed
    Below 1 Ω
    2 (SS2) - 5 (GND)
    Engine switch not pushed
    10 kΩ or higher
    Engine switch pushed
    Below 1 Ω

    Text in Illustration 
    *a
    Component without harness connected
    (Engine Switch)



NG
REPLACE ENGINE SWITCH (Click here)
OK


8.CHECK HARNESS AND CONNECTOR (POWER MANAGEMENT CONTROL ECU - ENGINE SWITCH)
  1. Disconnect the F80 power management control ECU connector.

  1. Disconnect the F71 engine switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F80-17 (SSW2) - F71-2 (SS2)
    Always
    Below 1 Ω
    F80-18 (SSW1) - F71-7 (SS1)
    F80-17 (SSW2) - Body ground
    Always
    10 kΩ or higher
    F80-18 (SSW1) - Body ground
    F71-5 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POWER MANAGEMENT CONTROL ECU (Click here)  

9.CHECK FOR DTC
  1. Connect the Techstream to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the Techstream on.

  1. Enter the following menus: Body Electrical / Power Source / Trouble Codes.

  1. Read the DTCs.

  1. Enter the following menus: Body Electrical / Smart Key / Trouble Codes.

  1. Read the DTCs.
    Result 
    Result
    Proceed to
    None of the following DTCs are output:
    B2785 Communication Malfunction between ECUs Connected by LIN
    B2287 LIN Communication Master Malfunction
    B2784 Antenna Coil Open/Short
    A
    DTC B2287 is output but B2785 is not output.
    B
    A DTC other than B2287 is output.
    C



B
GO TO DTC (B2287) (Click here)

C
GO TO DTC CHART (Click here)
A

GO TO SMART KEY SYSTEM (FOR ENTRY FUNCTION) (Room Oscillator does not Recognize Key) (Click here)