Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › SMART KEY SYSTEM (for Entry Function)

DTC    B27A8    Open in Outside Luggage Compartment Electrical Key Antenna Circuit

for Preparation Click here


DESCRIPTION

The certification ECU generates a request signal and transmits the signal to the electrical key antenna (outside luggage). The electrical key antenna (outside luggage) detects that the electrical key is brought close to the vehicle, and when a request signal is received from within 1.0 m (3.28 ft.) of the back door, the signal is transmitted. DTC B27A8 is stored by the certification ECU when an open circuit is detected in the circuit between the certification ECU and electrical key antenna (outside luggage) (CLG8 - CLG5, CG8B - CLGB).

DTC Code
DTC Detection Condition
Trouble Area
B27A8
An open circuit is detected in the circuit between the certification ECU and electrical key antenna (outside luggage) (CLG8 - CLG5, CG8B - CLGB).
  1. Harness or connector
  2. Electrical key antenna (outside luggage)
  3. Certification ECU

WIRING DIAGRAM


B210706E04


INSPECTION PROCEDURE

NOTICE:
  1. The smart key system (for Entry Function) uses a multiplex communication system (LIN communication system) and the CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the smart key system (for Entry Function) after confirming that the communication systems are functioning properly.
  2. When using the Techstream with the engine switch off to troubleshoot: Connect the Techstream to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the Techstream and vehicle begins.
  3. Before replacing the certification ECU, refer to the engine immobiliser system (w/ Smart Key System) (Click here).

1.CHECK CONNECTOR CONNECTION
  1. Turn the engine switch off.

  1. Check that the connectors are properly connected to the certification ECU and electrical key antenna (outside luggage).

    OK:
    Connectors are properly connected.



NG
CONNECT CONNECTORS PROPERLY
OK


2.CHECK HARNESS AND CONNECTOR (ELECTRICAL KEY ANTENNA - CERTIFICATION ECU)
  1. Disconnect the N21 antenna connector.

  1. Disconnect the F78 ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N21-1 (CLG5) - F78-19 (CLG8)
    Always
    Below 1 Ω
    N21-2 (CLGB) - F78-20 (CG8B)
    Always
    Below 1 Ω
    F78-19 (CLG8) - Body ground
    Always
    10 kΩ or higher
    F78-20 (CG8B) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.INSPECT ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE)
B226391E01
  1. Remove the outside electrical key antenna (outside luggage) (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (CLG5) - 2 (CLGB)
    Always
    Below 1 Ω



NG
REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE) (Click here)
OK


4.REPLACE CERTIFICATION ECU
  1. Temporarily replace the certification ECU with a new one (Click here).


NEXT


5.CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC B27A8 is not output.



NG
REPLACE ELECTRICAL KEY ANTENNA (OUTSIDE LUGGAGE) (Click here)
OK

END (CERTIFICATION ECU IS DEFECTIVE)