DTC P106B Evaporative Emission System Pressure Sensor - Secondary Air Injection Pressure Sensor Correlation |
| DTC No. | DTC Detection Condition | Trouble Area |
| P106B | The pressure detected by the canister pressure sensor (Vapor Pressure Pump*) and the pressure detected by the pressure sensor of either emission control valve (for Bank 1 or Bank 2) (Air Pump Pressure (Absolute)* or Air Pump2 Pressure (Absolute)*) differ by 6.98 kPa (52 mmHg) or more (2 trip detection logic). |
|
| Related DTC | P106B: Evaporative emission system pressure sensor - secondary air injection system pressure sensor correlation |
| Required Sensors/Components (Main) |
|
| Required Sensors/Components (Related) | - |
| Frequency of Operation | Once per driving cycle |
| Duration | Less than 65 seconds |
| MIL Operation | 2 driving cycles |
| Sequence of Operation | None |
| Monitor runs whenever following DTCs are not stored | P0452, P0453 (Evaporative Emission System Pressure Sensor) P2440, P2441, P2442, P2443, P2444, P2445 (Secondary Air Injection System) P2431, P2432, P2433, P2436, P2437, P2438 (Secondary Air Injection System Pressure Sensor) |
| Time elapsed after engine stop | 50 minutes |
| Time after ECM started by soak-timer | 60 seconds or more |
| Battery voltage | 10.5 V or higher |
| Intake air temperature | -10°C (14°F) or higher |
| Engine coolant temperature | -10°C (14°F) or higher |
| Difference between EVAP pressure and secondary air injection pressure (bank 1) | More than 6.98 kPa (52 mmHg) |
| Difference between EVAP pressure and secondary air injection pressure (bank 2) | More than 6.98 kPa (52 mmHg) |

| Techstream Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|
| 1.CHECK FOR ANY OTHER DTCS OUTPUT (IN ADDITION TO P106B) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.
Read the DTCs.
| Result | Proceed to |
| DTC P106B is output | A |
| DTC P106B and other DTCs are output | B |
|
| ||||
| A | |
| 2.READ VALUE USING TECHSTREAM (VAPOR PRESSURE PUMP, AIR PUMP PRESSURE (ABSOLUTE) AND AIR PUMP2 PRESSURE (ABSOLUTE)) |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump, Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute).
Compare the Vapor Pressure Pump, Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute) data from the Data List with the current atmospheric pressure*.
| Result | Proceed to |
| The Vapor Pressure Pump value differs from the atmospheric pressure by 3.5 kPa (26.25 mmHg) or more | A |
| The Air Pump Pressure (Absolute) value differs from the atmospheric pressure by 3.5 kPa (26.25 mmHg) or more | B |
| The Air Pump2 Pressure (Absolute) value differs from the atmospheric pressure by 3.5 kPa (26.25 mmHg) or more | C |
|
| ||||
|
| ||||
| A | |
| 3.REPLACE CANISTER PUMP MODULE |
Replace the canister pump module (Click here).
|
| ||||
| 4.REPLACE NO. 1 EMISSION CONTROL VALVE SET |
Replace the No. 1 emission control valve set (Click here).
|
| ||||
| 5.REPLACE NO. 2 EMISSION CONTROL VALVE SET |
Replace the No. 2 emission control valve set (Click here).
| NEXT | |
| 6.CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the Techstream to the DLC3.
Turn the ignition switch to ON and turn the Techstream on.
Enter the following menus: Powertrain / Engine and ECT / Data List / Vapor Pressure Pump, Air Pump Pressure (absolute) and Air Pump2 Pressure (Absolute).
Confirm that the difference between Vapor Pressure Pump and Air Pump Pressure (Absolute), and the difference between Vapor Pressure Pump and Air Pump2 Pressure (Absolute) are both 3.5 kPa (26.25 mmHg) or less.
| NEXT | ||
| ||