VEHICLE STABILITY CONTROL SYSTEM > VSC OFF Indicator Light Remains ON |

| 1.CHECK CAN COMMUNICATION LINE |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus (Click here).
|
| ||||
| OK | |
| 2.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU CSW CIRCUIT) |
Disconnect the A6 skid control ECU connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A6-9 (CSW) - Body ground | VSC OFF switch not pushed in | 10 kΩ or higher |
| VSC OFF switch pushed in | Below 1 Ω |
|
| ||||
| OK | |
| 3.CHECK TERMINAL VOLTAGE (EXI3) |
Disconnect the A6 skid control ECU connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A6-40 (EXI3) - Body ground | Ignition switch ON w/ Rear Differential Lock: Rear differential free | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU) |
| Result | Proceed to |
| OK | A |
| NG (for 4WD) | B |
| NG (for 2WD) | C |
|
| ||||
|
| ||||
| A | |
| 4.READ VALUE USING TECHSTREAM (TRAC/VSC OFF MODE) |
Turn the ignition switch off.
Connect the Techstream to the DLC3.
Turn the ignition switch to ON.
Turn the Techstream on.
Enter the following menus: Chassis / ABS/VSC/TRAC / Data List.
| Tester Display | Measurement Item/Range | Normal Condition | Diagnostic Note |
| TRAC/VSC Off Mode | TRAC/VSC off mode/ Normal, TRC OFF or VSC OFF | Normal: Normal mode TRC OFF: TRAC OFF mode VSC OFF: VSC OFF mode | - |
Check that the mode display changes according to VSC OFF switch operation.
|
| ||||
| OK | ||
| ||
| 5.INSPECT VSC OFF SWITCH |
Remove the VSC OFF switch (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 6 (OFF) - 3 (VSC) | Switch is not pushed | 10 kΩ or higher |
| Switch is pushed | Below 1 Ω |
| *a | Component without harness connected (VSC OFF Switch) |
|
| ||||
| OK | |
| 6.CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - VSC OFF SWITCH) |
Disconnect the A6 skid control ECU connector.
Disconnect the U6 VSC OFF switch connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A6-9 (CSW) - U6-6 (OFF) | Always | Below 1 Ω |
| A6-9 (CSW) - Body ground | Always | 10 kΩ or higher |
| U6-3 (VSC) - Body ground | Always | Below 1 Ω |
|
| ||||
| OK | ||
| ||
| 7.CHECK TERMINAL VOLTAGE (EXI3) |
Disconnect the A6 skid control ECU connector.
Disconnect the F47 four wheel drive control ECU connector.
w/ Rear Differential Lock:
Disconnect the D3 rear differential lock detection switch connector.
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A6-40 (EXI3) - Body ground | Always | 10 kΩ or higher |
| *a | Front view of wire harness connector (to Skid Control ECU) |
| Result | Proceed to |
| OK (w/o Rear Differential Lock) | A |
| OK (w/ Rear Differential Lock) | B |
| NG | C |
|
| ||||
|
| ||||
| A | |
| 8.CHECK TERMINAL VOLTAGE (EXI3) |
Disconnect the A6 skid control ECU connector.
Connect the F47 four wheel drive control ECU connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A6-40 (EXI3) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU) |
|
| ||||
| OK | ||
| ||
| 9.INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (REAR DIFFERENTIAL LOCK POSITION SWITCH) |
Remove the rear differential lock detection switch (Click here).
![]() |
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| 2 (+B) - 1 (GND) | Pushed in | Below 1 Ω |
| Not pushed in | 10 kΩ or higher |
| *a | Component without harness connected (Differential Lock Detection Switch (Differential Lock Position Switch)) |
|
| ||||
| OK | |
| 10.CHECK TERMINAL VOLTAGE (EXI3) |
Disconnect the A6 skid control ECU connector.
Connect the F47 four wheel drive control ECU connector.
![]() |
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| A6-40 (EXI3) - Body ground | Ignition switch ON | 11 to 14 V |
| *a | Front view of wire harness connector (to Skid Control ECU) |
|
| ||||
| OK | ||
| ||