Home › Audio / Visual / Telematics › CELLULAR COMMUNICATION › SAFETY CONNECT SYSTEM

DTC    B15C0    Short in GPS Antenna

DTC    B15C1    Open in GPS Antenna

for Preparation Click here


DESCRIPTION

This DTC is stored when the DCM (Telematics Transceiver) detects an open or a short in the telephone and GPS antenna circuit. The DCM (Telematics Transceiver) receives signals at a radio frequency of between 1574.42 and 1576.42 MHz through the telephone and GPS antenna. The cable is a 50 Ω coaxial cable.

DTC Code
DTC Detection Condition
Trouble Area
B15C0
Current for the telephone and GPS antenna is more than the malfunction criterion for 10 seconds when the ignition switch is ON.
  1. Telephone and GPS Antenna (Telephone Antenna Assembly)
  2. Telephone and GPS Antenna Cord (No. 3 Antenna Cord Sub-assembly)
  3. Telephone and GPS Antenna Cord (No. 2 Antenna Cord Sub-assembly)
  4. Telephone and GPS Antenna Cord (Instrument Panel Wire)
  5. DCM (Telematics Transceiver)
B15C1
Current for the telephone and GPS antenna is less than the malfunction criterion for 10 seconds when the ignition switch is ON.

HINT:
Refer to "Parts Location" for installation location of the telephone and GPS antenna cord (Click here).


INSPECTION PROCEDURE

1.CHECK FOR DTC
  1. Turn the ignition switch off.

  1. Connect the Techstream to the DLC3.

  1. Turn the ignition switch to ON and wait for 10 seconds.

  1. Perform "Health Check" and check for current DTCs (Click here).
    Result 
    Result
    Proceed to
    DTC B15C0 or B15C1 is output
    A
    DTC B15C0 and B15C1 is not output
    B



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT TELEPHONE AND GPS ANTENNA (DCM - TELEPHONE AND GPS ANTENNA)


    E205695E07
  1. Disconnect the G46 telephone and GPS antenna connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 (GPS2) - 1a
    Always
    4 to 11 kΩ

    Text in Illustration 
    *a
    Telephone Antenna Assembly



NG
REPLACE TELEPHONE AND GPS ANTENNA (TELEPHONE ANTENNA ASSEMBLY)
OK


3.INSPECT TELEPHONE AND GPS ANTENNA CORD (NO. 3 ANTENNA CORD SUB-ASSEMBLY)


    E205731E06
  1. Disconnect the No. 3 antenna cord sub-assembly from the telephone antenna assembly connector.

  1. Disconnect the No. 3 antenna cord sub-assembly from the No. 2 antenna cord sub-assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A-2 - B-1
    Always
    Below 1 Ω
    A-2a - B-1a
    Always
    Below 1 Ω
    A-2 - Body ground
    Always
    10 kΩ or higher
    A-2a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    Telephone Antenna Assembly Side
    *b
    No. 2 Antenna Cord Sub-assembly Side



NG
REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 3 ANTENNA CORD SUB-ASSEMBLY) (Click here)
OK


4.INSPECT TELEPHONE AND GPS ANTENNA CORD (NO. 2 ANTENNA CORD SUB-ASSEMBLY)


    E206197E07
  1. Disconnect the No. 2 antenna cord sub-assembly from the No. 3 antenna cord sub-assembly.

  1. Disconnect the No. 2 antenna cord sub-assembly from the No. 2 instrument panel wire.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C-1 - D-1
    Always
    Below 1 Ω
    C-1a - D-1a
    Always
    Below 1 Ω
    C-1 - Body ground
    Always
    10 kΩ or higher
    C-1a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    No. 3 Antenna Cord Sub-assembly Side
    *b
    Instrument Panel Wire Side



NG
REPLACE TELEPHONE AND GPS ANTENNA CORD (NO. 2 ANTENNA CORD SUB-ASSEMBLY) (Click here)
OK


5.INSPECT TELEPHONE AND GPS ANTENNA CORD (INSTRUMENT PANEL WIRE)


    E206199E02
  1. Disconnect the No. 2 instrument panel wire from the No. 2 antenna cord sub-assembly.

  1. Disconnect the No. 2 instrument panel wire from the DCM (telematics transceiver).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E-1 - G43-1
    Always
    Below 1 Ω
    E-3a - G43-1a
    Always
    Below 1 Ω
    E-3 - Body ground
    Always
    10 kΩ or higher
    E-3a - Body ground
    Always
    10 kΩ or higher

    Text in Illustration 
    *a
    No. 2 Antenna Cord Sub-assembly Side
    *b
    DCM (Telematics Transceiver) Side



NG
REPLACE TELEPHONE AND GPS ANTENNA CORD (INSTRUMENT PANEL WIRE)
OK


6.REPLACE TELEPHONE AND GPS ANTENNA (TELEPHONE ANTENNA ASSEMBLY)
  1. Replace the telephone antenna assembly with a normally functioning one and check if the same problem occurs again (Click here).

    OK:
    The system returns to normal.



NG
Go to step 7
OK

END (TELEPHONE AND GPS ANTENNA IS DEFECTIVE) 

7.REPLACE DCM (TELEMATICS TRANSCEIVER)
  1. Replace the DCM (Telematics Transceiver) (Click here).

    NOTICE:
    1. The ignition switch must be off.
    2. Do not replace the DCM (Telematics Transceiver) with one from another vehicle.


NEXT

PERFORM DCM ACTIVATION (Click here)