DTC P0122 Throttle Position Sensor Circuit Low Input |
DTC P0123 Throttle / Pedal Position Sensor / Switch "A" Circuit High Input |
DTC P0222 Throttle / Pedal Position Sensor / Switch "B" Circuit Low Input |
DTC P0223 Throttle / Pedal Position Sensor / Switch "B" Circuit High Input |
DTC P2135 Throttle / Pedal Position Sensor / Switch "A" / "B" Voltage Correlation |

| DTC No. | DTC Detection Condition | Trouble Area |
| P0122 | The voltage of VTA1 is 0.273 V or less for 0.024 seconds or more. (1 trip detection logic) |
|
| P0123 | The voltage of VTA1 is more than 4.736 V for 0.024 seconds or more. (1 trip detection logic) |
|
| P0222 | The voltage of VTA2 is 1.153 V or less for 0.024 seconds or more. (1 trip detection logic) |
|
| P0223 | The voltage of VTA2 is 4.772 V or more for 0.024 seconds or more. (1 trip detection logic) |
|
| P2135 | Deviation in voltages of VTA1 and VTA2 exceed thresholds for 0.212 seconds or more. (1 trip detection logic) |
|
| GTS Display | Accelerator Pedal Fully Released | Accelerator Pedal Fully Depressed |
| Throttle Position No. 1 | 0.213 to 4.772 V | 0.213 to 4.772 V |
| Throttle Position No. 2 | 0.213 to 4.772 V | 0.213 to 4.772 V |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING GTS (THROTTLE POSITION SENSOR) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Throttle Position No. 1 and Throttle Position No. 2.
Read the values displayed on the GTS.
| When Accelerator Pedal Released | When Accelerator Pedal Depressed | Trouble Area | Proceed to | ||
| Throttle Position No. 1 (VTA1) | Throttle Position No. 2 (VTA2) | Throttle Position No. 1 (VTA1) | Throttle Position No. 2 (VTA2) | ||
| 0 to 0.213 V | 0 to 0.213 V | 0 to 0.213 V | 0 to 0.213 V | VC circuit open | A |
| 4.772 to 5.0 V | 4.772 to 5.0 V | 4.772 to 5.0 V | 4.772 to 5.0 V | E2 circuit open | |
| 0 to 0.213 V, or 4.772 to 5.0 V | 0.213 V to 4.772 V | 0 to 0.213 V, or 4.772 to 5.0 V | 0.213 V to 4.772 V | VTA1 circuit open or ground short | |
| 0.213 V to 4.772 V | 0 to 0.213 V, or 4.772 to 5.0 V | 0.213 V to 4.772 V | 0 to 0.213 V, or 4.772 to 5.0 V | VTA2 circuit open or ground short | |
| 0.213 to 4.772 V | 0.213 to 4.772 V | 0.213 to 4.772 V | 0.213 to 4.772 V | Throttle position sensor circuit normal | B |
|
| ||||
| A | |
| 2.CHECK HARNESS AND CONNECTOR (THROTTLE POSITION SENSOR - ECM) |
Disconnect the throttle with motor body assembly connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-19 (VC) - C15-5 (VC) | Always | Below 1 Ω |
| A36-18 (VTA1) - C15-6 (VTA1) | Always | Below 1 Ω |
| A36-28 (VTA2) - C15-4 (VTA2) | Always | Below 1 Ω |
| A36-29 (E1) - C15-3 (E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A36-19(VC) or C15-5 (VC) - Body ground | Always | 10 kΩ or higher |
| A36-18 (VTA1) or C15-6 (VTA1) - Body ground | Always | 10 kΩ or higher |
| A36-29 (E1) or C15-3 (E2) - Body ground | Always | 10 kΩ or higher |
| A36-29 (E1) or C15-4 (VTA2) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 3.INSPECT ECM (VC VOLTAGE) |
![]() |
Disconnect the throttle with motor body assembly connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C15-5 (VC) - C15-3 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Throttle with Motor Body Assembly) |
|
| ||||
| OK | |
| 4.REPLACE THROTTLE WITH MOTOR BODY ASSEMBLY |
Replace the throttle with motor body assembly (Click here).
| NEXT | |
| 5.CHECK WHETHER DTC OUTPUT RECURS (THROTTLE POSITION SENSOR DTCS) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Start the engine.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read DTCs.
| Result | Proceed to |
| DTC P0122, P0123, P0222, P0223 and/or P2135 are output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||