Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

DTC    P0512    Starter Request Circuit

DTC    P0616    Starter Relay Circuit Low

DTC    P0617    Starter Relay Circuit High

DTC    P081A    Starter Disable Circuit Low

for Preparation Click here


MONITOR DESCRIPTION

While the engine is being cranked, battery voltage is applied to terminal STA of the ECM. If the ECM detects the starter control (STA) signal after the engine is started, it determines that there is a malfunction in the STA circuit. The ECM then illuminates the MIL and stores the DTC.

DTC No.
DTC Detection Condition
Trouble Area
P0512
Starter signal remains input for 30 seconds or more after engine started.
(1 trip detection logic)
  1. Starter system
  2. ST relay circuit
  3. ECM
P0616
No starter signal is input when engine started.
(1 trip detection logic)
  1. Starter system
  2. ST relay circuit
  3. ECM
P0617
Starter signal remains input after engine started.
(1 trip detection logic)
  1. Starter system
  2. ST relay circuit
  3. ECM
P081A
Short in ST CUT relay circuit is detected.
(1 trip detection logic)
  1. Starter system
  2. ST CUT relay circuit
  3. ECM

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC procedure) (Click here).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the GTS on.
  6. Idle the engine for 1 second or more.
  7. Enter the following menus: Powertrain / Engine / Trouble Codes.
  8. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  9. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  10. Input the DTC: P0512, P0616, P0617 or P081A.
  11. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  12. If the judgment result is INCOMPLETE or N/A and no pending DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM

Refer to Starter Signal Circuit .

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. The following troubleshooting flowchart is based on the premise that the engine can be cranked normally.
    If the engine does not crank, proceed to Problem Symptoms Table (Click here).
  2. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING GTS (STARTER SIGNAL, STARTER SWITCH)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / Starter Signal and Starter Switch.

  1. Read the value displayed on the GTS when the ignition switch is turned to ON and cranking.

    OK:

    GTS Display
    Condition
    Normal Condition
    Starter Signal
    Ignition switch ON
    OFF
    Cranking
    ON
    Starter Switch
    Ignition switch ON
    OFF
    Cranking
    ON


    Result 
    Result
    Proceed to
    NG (w/o Entry and Start System)
    A
    NG (w/ Entry and Start System)
    B
    OK
    C



B
Go to step 4

C
Go to step 9
A


2.INSPECT RELAY (ST)
  1. Inspect the ST relay .



NG
REPLACE RELAY (ST)
OK


3.CHECK HARNESS AND CONNECTOR (ST RELAY - ECM)
  1. Remove the ST relay from the engine room relay block assembly.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 3 - A33-17 (STSW2)
    Always
    Below 1 Ω
    ST relay terminal 1 - A35-26 (STA)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 3 or A33-17 (STSW2) - Body ground
    Always
    10 kΩ or higher
    ST relay terminal 1 or A35-26 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK STARTER SIGNAL CIRCUIT (W/O ENTRY AND START SYSTEM) (Click here)  

4.READ VALUE USING GTS (ST CUT RELAY)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / ST CUT Relay.

  1. Read the value displayed on the GTS when the ignition switch is turned to ON and cranking.

    OK:

    GTS Display
    Condition
    Normal Condition
    ST CUT Relay
    Ignition switch ON
    OFF
    Cranking
    ON



NG
Go to step 7
OK


5.INSPECT RELAY (ST)
  1. Inspect the ST relay .



NG
REPLACE RELAY (ST)
OK


6.CHECK HARNESS AND CONNECTOR (ST RELAY - ECM)
  1. Remove the ST relay from the engine room relay block assembly.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 3 - A33-17 (STSW2)
    Always
    Below 1 Ω
    ST relay terminal 1 - A35-26 (STA)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 3 or A33-17 (STSW2) - Body ground
    Always
    10 kΩ or higher
    ST relay terminal 1 or A35-26 (STA) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK STARTER SIGNAL CIRCUIT (W/ ENTRY AND START SYSTEM) (Click here)  

7.INSPECT RELAY (ST CUT)
  1. Inspect the ST CUT relay .



NG
REPLACE RELAY (ST CUT)
OK


8.CHECK HARNESS AND CONNECTOR (ST CUT RELAY - ECM)
  1. Remove the ST CUT relay from the engine room relay block assembly.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    ST CUT relay terminal 1 - A35-34 (STAR)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    ST CUT relay terminal 1 or A35-34 (STAR) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK STARTER SIGNAL CIRCUIT (W/ ENTRY AND START SYSTEM) (Click here)  

9.CHECK WHETHER DTC OUTPUT RECURS
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0512, P0616, P0617 or P081A is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

CHECK FOR INTERMITTENT PROBLEMS (Click here)