Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > Starter Signal Circuit

for Preparation Click here


DESCRIPTION

  1. w/ Entry and Start System
    While the engine is being cranked, the ECM detects the current from the ST relay drive circuit to the STSW2 and STA terminals, and carries out engine control when starting (STSW2 signal and STA signal). The ECM drives the ST relay until the engine start signal is input from the certification ECU (smart key ECU assembly), and drives the starter until a complete engine start is detected.
  1. w/o Entry and Start System
    While the engine is being cranked, the current from the ST relay flows to the ECM STSW2 terminal.

WIRING DIAGRAM


A280174E01


A280173E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK WHETHER ENGINE CAN BE CRANKED
  1. Check if the engine can be cranked.

    Result 
    Result
    Proceed to
    Engine cannot be cranked
    A
    Engine can be cranked (w/ Entry and Start System)
    B
    Engine can be cranked (w/o Entry and Start System)
    C



B
Go to step 19

C
Go to step 34
A


2.READ VALUE USING GTS (STARTER SIGNAL)
  1. Connect the GTS to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / Starter Signal.

  1. Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

    OK 
    Ignition Switch Position
    Starter Signal
    ON
    Close (OFF)
    START
    Open (ON)

    Result 
    Result
    Proceed to
    OK (w/ Entry and Start System)
    A
    NG (w/ Entry and Start System)
    B
    OK (w/o Entry and Start System)
    C
    NG (w/o Entry and Start System)
    D



B
Go to step 4

C
Go to step 21

D
Go to step 22
A


3.CHECK HARNESS AND CONNECTOR (ST RELAY - ECM - STARTER ASSEMBLY)
  1. Disconnect the ECM connector.

  1. Remove the ST relay from the engine room relay block assembly.

  1. Disconnect the starter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A33-14 (STSW2) - B1-1
    Always
    Below 1 Ω
    ST relay terminal 3 - B1-1
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A33-14 (STSW2), B1-1 or ST relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.READ VALUE USING GTS (STARTER CUT RELAY)
  1. Connect the GTS to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / Starter Cut Relay.

  1. Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

    OK 
    Ignition Switch Position
    Starter Cut Relay
    ON
    OFF
    START
    ON

    Result 
    Result
    Proceed to
    NG
    A
    OK (for automatic transmission models)
    B
    OK (for manual transmission models)
    C



B
Go to step 9

C
Go to step 14
A


5.CHECK HARNESS AND CONNECTOR (ECM - ST CUT RELAY)
  1. Disconnect the ECM connector.

  1. Remove the ST CUT relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A35-34 (STAR) - ST CUT relay terminal 1
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A35-34 (STAR) or ST CUT relay terminal 1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6.CHECK HARNESS AND CONNECTOR (IGS RELAY - ST CUT RELAY - BODY GROUND)
  1. Remove the ST CUT relay and IGS relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    ST CUT relay terminal 3 - IGS relay terminal 3
    Always
    Below 1 Ω
    ST CUT relay terminal 2 - IGS relay terminal 3
    Always
    Below 1 Ω
    IGS relay terminal 2 - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    ST CUT relay terminal 3, ST CUT relay terminal 2 or IGS relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7.INSPECT TERMINAL VOLTAGE (IGS RELAY)


    A280168E01
  1. Remove the IGS relay from the engine room relay block assembly.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    IGS relay terminal 5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Engine Room Relay Block Assembly
    *2
    IGS Relay Terminal



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


8.CHECK HARNESS AND CONNECTOR (ECM - IG2 RELAY - IGS RELAY)
  1. Disconnect the ECM connector.

  1. Remove the IG2 relay and IGS relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A33-27 (IGSW) - IG2 relay terminal 3
    Always
    Below 1 Ω
    IG2 relay terminal 3 - IGS relay terminal 1
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A33-27 (IGSW), IG2 relay terminal 3 or IGS relay terminal 1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ENTRY AND START SYSTEM (for Start Function) (Click here)  

9.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (Click here).



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


10.CHECK HARNESS AND CONNECTOR (SMART KEY ECU - PARK/NEUTRAL POSITION SWITCH)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Disconnect the smart key ECU assembly connector.

  1. Remove the INHIBITOR relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    L2-4 - D48-5 (NSW)
    Always
    Below 1 Ω
    L2-4 - INHIBITOR relay terminal 1
    Always
    Below 1 Ω
    L2-5 - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    L2-4, D48-5 (NSW) or INHIBITOR relay terminal 1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11.CHECK HARNESS AND CONNECTOR (ST CUT RELAY - INHIBITOR RELAY - ST RELAY)
  1. Remove the ST relay, ST CUT relay and INHIBITOR relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    ST CUT relay terminal 4 - INHIBITOR relay terminal 2
    Always
    Below 1 Ω
    ST CUT relay terminal 4 - INHIBITOR relay terminal 5
    Always
    Below 1 Ω
    ST CUT relay terminal 4 - ST relay terminal 5
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    ST CUT relay terminal 4, INHIBITOR relay terminal 2, INHIBITOR relay terminal 5 or ST relay terminal 5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.CHECK HARNESS AND CONNECTOR (INHIBITOR RELAY - ST RELAY)
  1. Remove the ST relay and INHIBITOR relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    INHIBITOR relay terminal 3 - ST relay terminal 2
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    INHIBITOR relay terminal 3 or ST relay terminal 2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
  1. Disconnect the ECM connector.

  1. Remove the ST relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A35-26 (STA) - ST relay terminal 1
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A35-26 (STA) or ST relay terminal 1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ENTRY AND START SYSTEM (for Start Function) (Click here)  

14.INSPECT CLUTCH START SWITCH ASSEMBLY
  1. Inspect the clutch start switch assembly (for LHD) .

  1. Inspect the clutch start switch assembly (for RHD) .


Result 
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPLACE CLUTCH START SWITCH ASSEMBLY (Click here)

C
REPLACE CLUTCH START SWITCH ASSEMBLY (Click here)
A


15.INSPECT TERMINAL VOLTAGE (+B OF CLUTCH START SWITCH ASSEMBLY)


    A280160E01
  1. Disconnect the clutch start switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A20-1 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Clutch Start Switch Assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


16.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ST RELAY - SMART KEY ECU ASSEMBLY)
  1. Disconnect the clutch start switch assembly connector.

  1. Remove the ST relay from the engine room relay block assembly.

  1. Disconnect the smart key ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    A20-2 - ST relay terminal 2
    Always
    Below 1 Ω
    A20-2 - D48-10 (CLUT)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A20-2, D48-10 (CLUT), or ST relay terminal 2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17.CHECK HARNESS AND CONNECTOR (ST RELAY - ST CUT RELAY)
  1. Remove the ST relay and ST CUT relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 5 - ST CUT relay terminal 4
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    ST relay terminal 5 or ST CUT relay terminal 4 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


18.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
  1. Disconnect the ECM connector.

  1. Remove the ST relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A35-26 (STA) - ST relay terminal 1
    Always
    Below 1 Ω
    A33-14 (STSW2) - ST relay terminal 3
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A35-26 (STA), A33-14 (STSW2), ST relay terminal 1 or ST relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

19.READ VALUE USING GTS (STARTER SIGNAL)
  1. Connect the GTS to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / Starter Signal.

  1. Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

    OK 
    Ignition Switch Position
    Starter Signal
    ON
    Close (OFF)
    START
    Open (ON)

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


20.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
  1. Disconnect the ECM connector.

  1. Remove the ST relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A35-26 (STA) - ST relay terminal 1
    Always
    Below 1 Ω
    A33-14 (STSW2) - ST relay terminal 3
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A35-26 (STA), A33-14 (STSW2), ST relay terminal 1 or ST relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

21.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY - STARTER ASSEMBLY)
  1. Disconnect the ECM connector.

  1. Disconnect the starter assembly connector.

  1. Remove the ST relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    B1-1 - A33-17 (STSW2)
    Always
    Below 1 Ω
    B1-1 - ST relay terminal 3
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A33-17 (STSW2), ST relay terminal 3 or B1-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


22.INSPECT IGNITION OR STARTER SWITCH ASSEMBLY
  1. Inspect the ignition or starter switch assembly (Click here).



NG
REPLACE IGNITION OR STARTER SWITCH ASSEMBLY (Click here)
OK


23.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - ST RELAY)
  1. Disconnect the ignition or starter switch assembly connector.

  1. Remove the ST relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    D55-8 (ST2) - ST relay terminal 5
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    D55-8 (ST2) or ST relay terminal 5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


24.INSPECT TERMINAL VOLTAGE (+B OF IGNITION OR STARTER SWITCH ASSEMBLY)


    A280162E01
  1. Disconnect the ignition or starter switch assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    D55-2 (AM1) - Body ground
    Always
    11 to 14 V
    D55-7 (AM2) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Ignition or Starter Switch Assembly)
    Result 
    Result
    Proceed to
    NG
    A
    OK (for Automatic Transmission)
    B
    OK (for Manual Transmission)
    C



B
Go to step 25

C
Go to step 30
A

REPAIR OR REPLACE HARNESS OR CONNECTOR 

25.INSPECT PARK/NEUTRAL POSITION SWITCH ASSEMBLY
  1. Inspect the park/neutral position switch assembly (Click here).



NG
REPLACE PARK/NEUTRAL POSITION SWITCH ASSEMBLY (Click here)
OK


26.CHECK HARNESS AND CONNECTOR (PARK/NEUTRAL POSITION SWITCH ASSEMBLY - INHIBITOR RELAY)
  1. Disconnect the park/neutral position switch assembly connector.

  1. Remove the INHIBITOR relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    L2-4 - INHIBITOR relay terminal 1
    Always
    Below 1 Ω
    L2-5 - Body ground
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    L2-4 or INHIBITOR relay terminal 1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


27.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - INHIBITOR RELAY)
  1. Disconnect the ignition or starter switch assembly connector.

  1. Remove the INHIBITOR relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    D55-1 (ST1) - INHIBITOR relay terminal 5
    Always
    Below 1 Ω
    D55-1 (ST1) - INHIBITOR relay terminal 2
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    D55-1 (ST1), INHIBITOR relay terminal 2 or INHIBITOR relay terminal 5 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


28.CHECK HARNESS AND CONNECTOR (INHIBITOR RELAY - ST RELAY)
  1. Remove the INHIBITOR relay and ST relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    INHIBITOR relay terminal 3 - ST relay terminal 2
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    INHIBITOR relay terminal 3 or ST relay terminal 2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


29.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
  1. Disconnect the ECM connector.

  1. Remove the ST relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A35-26 (STA) - ST relay terminal 1
    Always
    Below 1 Ω
    A33-17 (STSW2) - ST relay terminal 3
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A35-26 (STA), A33-17 (STSW2), ST relay terminal 1 or ST relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

30.INSPECT CLUTCH START SWITCH ASSEMBLY
  1. Inspect the clutch start switch assembly (for LHD) .

  1. Inspect the clutch start switch assembly (for RHD) .


Result 
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPLACE CLUTCH START SWITCH ASSEMBLY (Click here)

C
REPLACE CLUTCH START SWITCH ASSEMBLY (Click here)
A


31.CHECK HARNESS AND CONNECTOR (IGNITION OR STARTER SWITCH ASSEMBLY - CLUTCH START SWITCH)
  1. Disconnect the ignition or starter switch assembly connector.

  1. Disconnect the clutch start switch assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    D55-1 (ST1) - A20-1
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    D55-1 (ST1) or A20-1 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


32.CHECK HARNESS AND CONNECTOR (CLUTCH START SWITCH - ST RELAY)
  1. Disconnect the clutch start switch assembly connector.

  1. Remove the ST relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A20-2 - ST relay terminal 2
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A20-2 or ST relay terminal 2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


33.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
  1. Disconnect the ECM connector.

  1. Remove the ST relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A35-26 (STA) - ST relay terminal 1
    Always
    Below 1 Ω
    A33-17 (STSW2) - ST relay terminal 3
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A35-26 (STA), A33-17 (STSW2), ST relay terminal 1 or ST relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)  

34.READ VALUE USING GTS (ST SIGNAL)
  1. Connect the GTS to DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / Starter Signal.

  1. Check the value displayed on the GTS when the ignition switch is turned to the ON and START positions.

    OK 
    Ignition Switch Position
    Starter Signal
    ON
    Close (OFF)
    START
    Open (ON)

    Result 
    Result
    Proceed to
    NG
    A
    OK
    B



B
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
A


35.CHECK HARNESS AND CONNECTOR (ECM - ST RELAY)
  1. Disconnect the ECM connector.

  1. Remove the ST relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A35-26 (STA) - ST relay terminal 1
    Always
    Below 1 Ω
    A33-17 (STSW2) - ST relay terminal 3
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A35-26 (STA), A33-17 (STSW2), ST relay terminal 1 or ST relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)