Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

DTC    P0335    Crankshaft Position Sensor "A" Circuit

DTC    P0336    Crankshaft Position Sensor Range / Performance

for Preparation Click here


DESCRIPTION

The crankshaft position sensor system consists of a No. 1 crankshaft position sensor plate and Magneto Resistive Element (MRE) type sensor. The No. 1 crankshaft angle sensor plate is installed on the crankshaft. The crankshaft position sensor generates 30 signals per crankshaft revolution. The ECM uses the camshaft position signal to distinguish between the cylinders, and uses the crankshaft position signal to detect the crankshaft position and engine speed.

DTC No.
DTC Detection Condition
Trouble Area
P0335
No crankshaft position sensor signal is sent to the ECM while cranking for 3 seconds or more.
(1 trip detection logic)
  1. Open or short in crankshaft position sensor circuit
  2. Crankshaft position sensor
  3. No. 1 crankshaft angle sensor plate (crankshaft sub-assembly)
  4. ECM
P0336
Crankshaft position sensor signal is not 30 counts per 1 revolution of crankshaft 10 times continuously.
(2 trip detection logic)
  1. Crankshaft position sensor
  2. No. 1 crankshaft angle sensor plate (crankshaft sub-assembly)
  3. ECM

MONITOR DESCRIPTION

If there is no signal from the crankshaft position sensor despite the crankshaft revolving, the ECM interprets this as a malfunction of the sensor and the ECM illuminates the MIL and sets a DTC.

CONFIRMATION DRIVING PATTERN

  1. Connect the GTS to the DLC3.
  2. Turn the ignition switch to ON and turn the GTS on.
  3. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
  4. Turn the ignition switch off and wait for at least 30 seconds.
  5. Turn the ignition switch to ON and turn the GTS on.
  6. Start the engine.

    HINT:
    If the engine could not be started, crank engine for 10 seconds.

  7. Idle the engine for 20 seconds or more.
  8. Enter the following menus: Powertrain / Engine / Trouble Codes.
  9. Read pending DTCs.

    HINT:
    1. If a pending DTC is output, the system is malfunctioning.
    2. If a pending DTC is not output, perform the following procedure.

  10. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
  11. Input the DTC: P0335 or P0336.
  12. Check the DTC judgment result.

    GTS Display
    Description
    NORMAL
    1. DTC judgment completed
    2. System normal
    ABNORMAL
    1. DTC judgment completed
    2. System abnormal
    INCOMPLETE
    1. DTC judgment not completed
    2. Perform driving pattern after confirming DTC enabling conditions
    N/A
    1. Unable to perform DTC judgment
    2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

    HINT:
    1. If the judgment result shows NORMAL, the system is normal.
    2. If the judgment result shows ABNORMAL, the system has a malfunction.

  13. If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

    HINT:
    1. If a permanent DTC is output, the system is malfunctioning.
    2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A384640E01


INSPECTION PROCEDURE

HINT:
  1. If no problem is found by this diagnostic troubleshooting procedure, check for problems by referring to the engine mechanical section.
  2. The engine speed can be checked by using the GTS. To perform the check, follow the procedures below:
    1. Connect the GTS to the DLC3.
    2. Start the engine.
    3. Turn the GTS on.
    4. Enter the following menus: Powertrain / Engine / Data List / Engine Speed.
    1. The engine speed may be indicated as zero despite the engine running normally. This is caused by a lack of NE signals from the crankshaft position sensor. Alternatively, the engine speed may be indicated as lower than the actual engine speed if the crankshaft position sensor output voltage is insufficient.
  3. Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING GTS (ENGINE SPEED)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / Engine Speed.

  1. Start the engine.

  1. Read the values displayed on the GTS while the engine is running.

    OK:
    Correct values are displayed.

    HINT:
    1. To check the engine speed change, display the graph on the GTS.
    2. If the engine does not start, check the engine speed while cranking.
    3. If the engine speed indicated on the GTS remains zero (0), there may be an open or short in the Crankshaft Position sensor circuit.



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)  

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF CRANKSHAFT POSITION SENSOR)
  1. Disconnect the crankshaft position sensor connector.



    A384641E01
  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C47-3 (VCC) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

Text in Illustration 
*a
Front view of wire harness connector
(to Crankshaft Position Sensor)


NG
Go to step 8
OK


3.CHECK HARNESS AND CONNECTOR (ECM - CRANKSHAFT POSITION SENSOR)
  1. Disconnect the ECM connector.

  1. Disconnect the crankshaft position sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A34-16 (NE+) - C47-1 (OUT)
    Always
    Below 1 Ω
    A34-27 (NE-) - C47-2 (GND)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A34-16 (NE+) or C47-1 (OUT) - Body ground
    Always
    10 kΩ or higher
    A34-27 (NE-) or C47-2 (GND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.CHECK SENSOR INSTALLATION (CRANKSHAFT POSITION SENSOR)
B319222E02
  1. Check the crankshaft position sensor installation.

    OK:
    Sensor is installed correctly.

Text in Illustration 
*a
Clearance
*b
OK
*c
NG


NG
SECURELY REINSTALL SENSOR (Click here)
OK


5.INSPECT CRANKSHAFT (TEETH OF SENSOR PLATE)
  1. Check the teeth of the No. 1 crankshaft position sensor plate.

    OK:
    Sensor plate does not have any cracks or deformation.



NG
REPLACE NO. 1 CRANKSHAFT POSITION SENSOR PLATE (Click here)
OK


6.REPLACE CRANKSHAFT POSITION SENSOR
  1. Replace the crankshaft position sensor (Click here).


NEXT


7.CHECK WHETHER DTC OUTPUT RECURS (DTC P0335 OR P0336)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Clear the DTCs (Click here).

  1. Turn the ignition switch off and wait for at least 30 seconds.

  1. Turn the ignition switch to ON and turn the tester on.

  1. Start the engine.

  1. Drive the vehicle in accordance with the driving pattern described in the Confirmation Driving Pattern.

  1. Enter the following menus: Powertrain / Engine / Trouble Codes.

  1. Read DTCs.

    Result 
    Result
    Proceed to
    No DTC is output
    A
    P0335 or P0336 is output
    B

    HINT:
    If the engine does not start, replace the ECM.



B
REPLACE ECM (Click here)
A

END 

8.CHECK HARNESS AND CONNECTOR (ECM - CRANKSHAFT POSITION SENSOR)
  1. Disconnect the ECM connector.

  1. Disconnect the crankshaft position sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A36-19 (VC) - C47-3 (VCC)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A36-19 (VC) or C47-3 (VCC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)