DTC P0107 Manifold Absolute Pressure / Barometric Pressure Circuit Low Input |
DTC P0108 Manifold Absolute Pressure / Barometric Pressure Circuit High Input |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0107 | Manifold absolute pressure sensor voltage is 0.61 V or less for 0.5 seconds or more. (1 trip detection logic) |
|
| P0108 | Manifold absolute pressure sensor voltage is 3.906 V or more for 0.5 seconds or more. (1 trip detection logic) |
| Manifold Absolute Pressure (kPa [mmHg]) | Malfunction |
| Approximately 0 [0] | Short in MAP circuit |
| 141 [1058] or more |
|

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING GTS (MAP) |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / MAP.
Read the value displayed on the GTS.
| Condition | MAP |
| Ignition switch ON | 80 to 110 kPa |
|
| ||||
| OK | ||
| ||
| 2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF MANIFOLD ABSOLUTE PRESSURE SENSOR) |
![]() |
Disconnect the manifold absolute pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C18-3 (VC) - C18-1 (E2) | Ignition switch ON | 4.5 to 5.5 V |
| C18-2 (PIM) - C18-1 (E2) | Ignition switch ON | 4.0 to 5.0 V |
| *a | Front view of wire harness connector (to Manifold Absolute Pressure Sensor) |
|
| ||||
| OK | |
| 3.REPLACE MANIFOLD ABSOLUTE PRESSURE SENSOR |
Replace the manifold absolute pressure sensor (Click here).
| NEXT | |
| 4.PERFORM CONFIRMATION DRIVING PATTERN |
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Clear the DTCs (Click here).
Turn the ignition switch off and wait for at least 30 seconds.
Turn the ignition switch to ON and turn the GTS on.
Start the engine and warm it up.
Drive the vehicle in accordance with the driving pattern described in Confirmation Driving Pattern.
Enter the following menus: Powertrain / Engine / Trouble Codes.
Read the DTC.
| Result | Proceed to |
| DTC P0107 or P0108 is output | A |
| DTC is not output | B |
|
| ||||
| A | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (MANIFOLD ABSOLUTE PRESSURE SENSOR - ECM) |
Disconnect the manifold absolute pressure sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-19 (VC) - C18-3 (VC) | Always | Below 1 Ω |
| A34-20 (PIM) - C18-2 (PIM) | Always | Below 1 Ω |
| A36-29 (E1) - C18-1(E2) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A36-19 (VC) or C18-3 (VC) - Body ground | Always | 10 kΩ or higher |
| A34-20 (PIM) or C18-2 (PIM) - Body ground | Always | 10 kΩ or higher |
| A36-29 (E1) or C18-1 (E2) or Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||