Home › Drivetrain · TX6A AUTOMATIC TRANSMISSION / TRANSAXLE › AUTOMATIC TRANSMISSION SYSTEM

DTC    P0712    Transmission Fluid Temperature Sensor "A" Circuit Low Input

DTC    P0713    Transmission Fluid Temperature Sensor "A" Circuit High Input

for Preparation Click here


DESCRIPTION

The oil temperature sensor within the valve body detects the oil temperature within the transmission hydraulic control circuit, and inputs into the TCM a signal corresponding to the oil temperature.
G031389E04

DTC No.
DTC Detection Condition
  1. Diagnosis Condition
  2. Malfunction Status
  3. Malfunction Time
  4. Other
Trouble Area
P0712
  1. Not learning control prohibited status
  2. The oil temperature sensor input voltage is 0.05 V or less
  3. Detects a malfunction that continues for 10 seconds 6 times consecutively
  4. 1-trip detection logic
  1. Transmission wire (ATF temperature sensor)
  2. Harness and connector
  3. TCM
P0713
  1. Park/neutral position switch assembly is normal, and shift lever is in D or R for 1 min. or more
    Not learning control prohibited status
  2. The oil temperature sensor input voltage is 4.94 V or more
  3. Detects a malfunction that continues for 1 second 12 times consecutively
  4. 1-trip detection logic
  1. Transmission wire (ATF temperature sensor)
  2. Harness and connector
  3. TCM

MONITOR DESCRIPTION

These DTCs indicate an open or short in the automatic transmission fluid (ATF) temperature sensor circuit. The automatic transmission fluid (ATF) temperature sensor converts ATF temperature to an electrical resistance value. Based on the resistance, the TCM determines the ATF temperature, and the TCM detects an open or short in the ATF temperature circuit. If the resistance value of the ATF temperature is less than 0.049 V or more than 4.932 V , the TCM interprets this as a fault in the ATF sensor or wiring. The TCM will turn on the MIL and store the DTC.

WIRING DIAGRAM


C250700E01


INSPECTION PROCEDURE

NOTICE:
Perform the universal trip to clear permanent DTCs (Click here).


DATA LIST

HINT:
Using the GTS to read the Data List allows the values or states of switches, sensors, actuators and other items to be read without removing any parts. This non-intrusive inspection can be very useful because intermittent conditions or signals may be discovered before parts or wiring is disturbed. Reading the Data List information early in troubleshooting is one way to save diagnostic time.

NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not depend solely on these reference values when deciding whether a part is faulty or not.

  1. Warm up the engine.

  2. Turn the ignition switch off.

  3. Connect the GTS to the DLC3.

  4. Turn the ignition switch ON.

  5. Turn the GTS on.

  6. Enter the following menus: Powertrain / ECT / Data List.

  7. According to the display on the GTS, read the "Data List".

    Item
    Measurement Item/
    Range (display)
    Normal Condition
    A/T Oil Temperature 1
    ATF Temp. Sensor Value/
    min.: -40°C (-40°F)
    max.: 215°C (419°F)
    1. After Stall Test;
      Approx. 80°C (176°F)
    2. Equal to ambient temperature when cold soak

    HINT:
    When DTC P0712 is output and GTS output is -40°C (-40°F) or more, there is a short circuit.
    When DTC P0713 is output and GTS output is 171°C (340°F), there is an open circuit.


    Temperature Displayed
    Malfunction
    171°C (340°F)
    Open circuit
    -40°C (-40°F) or more
    Short circuit

1.INSPECT TRANSMISSION WIRE (ATF TEMPERATURE SENSOR)
  1. Disconnect the A18 TCM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A18-22(OIL) - A18-23(EOIL)
    Always
    79 Ω to 156 kΩ

  1. Connect the A18 TCM connector.



NG
Go to step 3
OK


2.REPLACE TCM
  1. Replace the TCM (Click here).


NEXT

PERFORM THE RESET MEMORY (Click here)  

3.CHECK HARNESS AND CONNECTOR (TRANSMISSION WIRE - TCM)
  1. Disconnect the A18 TCM connector.

  1. Disconnect the L4 transmission wire connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Tester Connection
    Condition
    Specified Condition
    L4-8(EOIL) - Body ground
    Ignition switch ON
    Below 1 V
    L4-15(OIL) - Body ground
    Ignition switch ON
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard resistance:
    Tester Connection
    Condition
    Specified Condition
    A18-22(OIL) - L4-15(OIL)
    Always
    Below 1 Ω
    A18-23(EOIL) - L4-8(EOIL)
    Always
    Below 1 Ω
    L4-8(EOIL) - Body ground
    Always
    10 kΩ or higher
    L4-15(OIL) - Body ground
    Always
    10 kΩ or higher

  1. Connect the A18 TCM connector.

  1. Connect the L4 transmission wire connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE TRANSMISSION WIRE (Click here)