Home › Steering › STEERING COLUMN › STEERING COLUMN ASSEMBLY

STEERING COLUMN ASSEMBLY > INSTALLATION

for Preparation Click here


HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.



1. INSPECT STEERING COLUMN ASSEMBLY


    C260481E01
  1. Check that the 2 capsules are securely installed to the steering column assembly as shown in the illustration.

    OK:
    5.0 mm (0.1969 in.) or more

    Text in Illustration 
    *1
    Capsule
    If the capsules are not positioned as specified, replace the steering column assembly with a new one.

  1. Check the 2 capsules for deformation and damage.
    If either of the capsules is deformed, loose, missing or damaged, replace the steering column assembly with a new one.



2. INSTALL STEERING COLUMN ASSEMBLY
  1. Install the steering column assembly with the 2 nuts and new bolt.

    Torque:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    NOTICE:
    When installing the steering column assembly, be careful that the wire harness does not interfere with or is not pinched between other parts.



    C260486E01
  1. Engage the clamp.

  1. Connect the 2 connectors to the power steering ECU.

    1. As shown in the illustration, return the lock lever to its original position to connect the connector and securely push in the lock of the lock lever.

  1. Connect the each connector and engage the wire harness clamps to the steering column assembly.
    Text in Illustration 
    *a
    Return the lock lever
    *b
    Push in the lock



3. INSTALL STEERING INTERMEDIATE SHAFT ASSEMBLY
  1. Pass the steering intermediate shaft assembly through the hole in the body from the inside of the cabin.



    C260472E01
  1. Connect the steering intermediate shaft assembly to the rack and pinion power steering gear assembly.
    Text in Illustration 
    *1
    Matchmark

    NOTICE:
    Align the matchmarks on the steering intermediate shaft assembly and the rack and pinion power steering gear assembly.

  1. Install the new bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }



    C263656E01
  1. Install the steering intermediate shaft assembly to the steering column assembly.
    Text in Illustration 
    *1
    Matchmark

    NOTICE:
    Align the matchmarks on the steering intermediate shaft assembly and the steering column assembly.

  1. Install the new bolt.

    Torque:
    35 N*m{ 357 kgf*cm , 26 ft.*lbf }

  1. Engage the 4 claws and install the dust seal.



4. INSTALL TURN SIGNAL SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY

NOTICE:
  1. Do not replace the spiral cable with the battery connected and the ignition switch ON.
  2. Do not rotate the spiral cable without the steering wheel with the battery connected and the ignition switch ON.
  3. Ensure that the steering wheel is installed and aligned straight when inspecting the steering sensor.

  1. With the clamp loosened, install the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly.

  1. Engage the claw on the turn signal switch assembly with spiral cable sub-assembly to the steering column assembly and tighten the clamp.

  1. Connect the each connector to the turn signal switch assembly with spiral cable sub-assembly.



5. INSTALL UPPER STEERING COLUMN COVER
  1. Engage the 2 claws to install the upper steering column cover.



6. INSTALL LOWER STEERING COLUMN COVER
  1. w/ Knee Airbag

    1. Engage the 4 claws to install the lower steering column cover.

    2. Install the 2 screws.

  1. w/o Knee Airbag

    1. Engage the 6 claws to install the lower steering column cover.

    2. Install the 2 screws.



7. INSTALL STEERING COLUMN COVER SUPPORT (w/ Entry and Start System)
  1. Engage the 4 claws and install the steering column cover support.



8. INSTALL UPPER INSTRUMENT PANEL METER ORNAMENT
  1. Connect the connector.

  1. Engage the 2 claws that are holding the upper instrument panel meter ornament and steering column cover together.

  1. Engage the 2 clips and 6 claws.

  1. Install the upper instrument panel meter ornament with the screw.



9. INSTALL METER HOOD SUB-ASSEMBLY
  1. Engage the 12 claws.

  1. Install the meter hood sub-assembly with the screw.



10. INSTALL CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY
  1. Engage the 4 clips and 2 claws to install the center instrument cluster finish panel sub-assembly.



11. TURN FRONT WHEELS TO FACE STRAIGHT AHEAD


12. INSPECT AND ADJUST SPIRAL CABLE WITH SENSOR SUB-ASSEMBLY

NOTICE:
Do not adjust the spiral cable sub-assembly with the battery connected and the ignition switch ON.

  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    The power window system utilizes a mechanism that the door glass moves down slightly when the door is opened, and that the glass moves up when closing the door in order to prevent the door molding from being damaged. When the battery negative (-) terminal needs to be disconnected for servicing, fully open the driver and passenger door glasses in advance.



    B311948E01
  1. Check if the spiral cable sub-assembly is centered.
    Text in Illustration 
    *1
    Matching Mark
    *2
    Colored Part

    HINT:
    When the spiral cable is attached in a central position, it will align with the matching mark, allowing the colored area indicated in the illustration to be checked.



  1. If the spiral cable sub-assembly is not centered, center it.

    NOTICE:
    Do not turn the spiral cable sub-assembly using the airbag wire harness.




      B311952
    1. Rotate the spiral cable sub-assembly counterclockwise slowly by hand until it stops.



    2. B311989E01
    3. Rotate the spiral cable sub-assembly clockwise approximately 2.5 turns to the position where the matching mark is matched.
      Text in Illustration 
      *1
      Matching Mark
      *2
      Colored Part

      HINT:
      1. The spiral cable sub-assembly will rotate approximately 2.5 turns to both the left and right from the center.
      2. When centering is not possible, there may be an open circuit in the spiral cable. Replace the spiral cable and steering sensor with new ones.



13. INSPECT STEERING WHEEL CENTER POINT


14. INSTALL STEERING WHEEL ASSEMBLY
(Click here)


15. INSTALL LOWER NO. 1 INSTRUMENT PANEL AIRBAG ASSEMBLY (w/ Knee Airbag)
(Click here)


16. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/o Knee Airbag)
  1. Connect each connector.



    B312545E01
  1. for Automatic Air Conditioning System for RHD:

    1. Connect the connector.

    2. Engage the guide and connect the aspirator hose.
      Text in Illustration 
      *1
      Aspirator Hose

  1. Engage the 4 claws.

  1. Engage the 4 clips to install the No. 1 instrument panel under cover sub-assembly.

  1. Install the 2 screws.



17. INSTALL INSTRUMENT SIDE PANEL (w/o Knee Airbag)


    B322066
  1. Engage the 4 clips and claw to install the instrument side panel.



18. INSTALL NO. 1 ENGINE UNDER COVER


    A280546
  1. Install the No. 1 engine under cover with the 12 bolts and engage the 7 clips.
    V100135
    Bolt A
    V100136
    Bolt B

    Torque:
    Bolt A:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }
    Bolt B:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



19. INSTALL NO. 2 ENGINE UNDER COVER
  1. Install the 7 bolts and the No. 2 engine under cover.

    Torque:
    7.5 N*m{ 76 kgf*cm , 66 in.*lbf }



20. VSC SENSOR NEUTRAL MEMORIZATION
(Click here)


21. ROTATION ANGLE SENSOR INITIALIZATION AND TORQUE SENSOR ZERO POINT CALIBRATION
(Click here)