Home › Vehicle Interior › SUPPLEMENTAL RESTRAINT SYSTEMS › AIRBAG SYSTEM

DTC    B1810    Short in D Squib (Dual Stage - 2nd Step) Circuit

DTC    B1811    Open in D Squib (Dual Stage - 2nd Step) Circuit

DTC    B1812    Short in D Squib (Dual Stage - 2nd Step) Circuit (to Ground)

DTC    B1813    Short in D Squib (Dual Stage - 2nd Step) Circuit (to +B)

for Preparation Click here


DESCRIPTION

  1. The driver side squib 2nd step circuit consists of the airbag ECU assembly, spiral cable sub-assembly and horn button assembly.
  2. The airbag ECU assembly uses this circuit to deploy the airbag when deployment conditions are met.
  3. These DTCs are stored when a malfunction is detected in the driver side squib 2nd step circuit.

DTC No.
DTC Detection Condition
Trouble Area
B1810
  1. The airbag ECU assembly receives a line short circuit signal in the driver side squib 2nd step circuit during primary check.
  2. Spiral cable sub-assembly malfunction
  3. Driver side squib 2nd step malfunction
  4. Airbag ECU assembly malfunction
  1. Instrument panel wire
  2. Spiral cable sub-assembly
  3. Horn button assembly (Driver side squib 2nd step)
  4. Airbag ECU assembly
B1811
  1. The airbag ECU assembly receives an open circuit signal in the driver side squib 2nd step circuit.
  2. Spiral cable sub-assembly malfunction
  3. Driver side squib 2nd step malfunction
  4. Airbag ECU assembly malfunction
B1812
  1. The airbag ECU assembly receives a short circuit to ground signal in the driver side squib 2nd step circuit.
  2. Spiral cable sub-assembly malfunction
  3. Driver side squib 2nd step malfunction
  4. Airbag ECU assembly malfunction
B1813
  1. The airbag ECU assembly receives a short circuit to B+ signal in the driver side squib 2nd step circuit.
  2. Spiral cable sub-assembly malfunction
  3. Driver side squib 2nd step malfunction
  4. Airbag ECU assembly malfunction

WIRING DIAGRAM


C239226E18


INSPECTION PROCEDURE

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the negative (-) battery terminal. Therefore, make sure to read the disconnecting the cable from the negative (-) battery terminal notices before proceeding with work (Click here).

HINT:
  1. Perform the simulation method by selecting check mode (Signal Check) using the GTS (Click here).
  2. After selecting check mode (Signal Check), perform the simulation method by wiggling each connector of the airbag system or driving the vehicle on a city road or rough road (Click here).

1.CHECK CONNECTORS


    C241740E01
  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check that the connectors are properly connected to the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.

    OK:
    The connectors are properly connected.

    HINT:
    If the connectors are not connected securely, reconnect the connectors and proceed to the next inspection.

  1. Disconnect the connectors from the horn button assembly, spiral cable sub-assembly and airbag ECU assembly.

  1. Check that the terminals of the connectors are not damaged.

    OK:
    The terminals are not deformed or damaged.

  1. Check that the spiral cable sub-assembly connector (on the horn button assembly side) is not damaged.

    OK:
    The lock button is not disengaged, or the claw of the lock is not deformed or damaged.

  1. Check that the short springs for the instrument panel wire and spiral cable sub-assembly with the activation prevention mechanism are not deformed or damaged.

    OK:
    The short springs are not deformed or damaged.

    Text in Illustration 
    *1
    Horn Button Assembly
    *2
    Spiral Cable Sub-assembly
    *3
    Airbag ECU Assembly
    *4
    Instrument Panel Wire



NG
REPLACE WIRE HARNESS
OK


2.CHECK HORN BUTTON ASSEMBLY (DRIVER SIDE SQUIB 2ND STEP)


    C263725E02
  1. Connect the instrument panel wire to the airbag ECU assembly and spiral cable sub-assembly.

  1. Connect SST (resistance 2.1 Ω) to connector E (black connector).

    CAUTION:
    Never connect the tester to the horn button assembly (driver side squib 2nd step) for measurement, as this may lead to a serious injury due to airbag deployment.

    NOTICE:
    1. Do not forcibly insert SST into the terminals of the connector when connecting it.
    2. Insert SST straight into the terminals of the connector.

SST
09843-18061  
  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1810, B1811, B1812 or B1813 is not output.

    HINT:
    Codes other than DTCs B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.

  1. Turn the ignition switch off.

  1. Disconnect the cable from the negative (-) battery terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Disconnect SST from connector E.
    Text in Illustration 
    *1
    Horn Button Assembly
    *2
    Spiral Cable Sub-assembly
    *3
    Airbag ECU Assembly
    *a
    Front view of wire harness connector
    (to Horn Button Assembly)
    *b
    Color: Black



NG
Go to step 3
OK

REPLACE HORN BUTTON ASSEMBLY (Click here)  

3.CHECK DRIVER SIDE SQUIB 2ND STEP CIRCUIT


    C259340E02
  1. Disconnect the instrument panel wire from the airbag ECU assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      z6-1 (D2+) - Body ground
      Ignition switch ON
      Below 1 V
      z6-2 (D2-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check for an open in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      z6-1 (D2+) - z6-2 (D2-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      z6-1 (D2+) - Body ground
      Always
      1 MΩ or higher
      z6-2 (D2-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      z6-1 (D2+) - z6-2 (D2-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.
      Text in Illustration 
      *1
      Horn Button Assembly
      *2
      Spiral Cable Sub-assembly
      *3
      Airbag ECU Assembly
      *a
      Front view of wire harness connector
      (to Horn Button Assembly)
      *b
      Color: Black



NG
Go to step 5
OK


4.CHECK DTC


    C238229E01
  1. Connect the connectors to the horn button assembly and airbag ECU assembly.

  1. Connect the cable to the negative (-) battery terminal.

  1. Clear the DTCs stored in memory (Click here).

  1. Turn the ignition switch off.

  1. Turn the ignition switch to ON, and wait for at least 60 seconds.

  1. Check for DTCs (Click here).

    OK:
    DTC B1810, B1811, B1812 or B1813 is not output.

    HINT:
    Codes other than DTCs B1810, B1811, B1812 and B1813 may be output at this time, but they are not related to this check.

    Text in Illustration 
    *1
    Horn Button Assembly
    *2
    Spiral Cable Sub-assembly
    *3
    Airbag ECU Assembly



NG
REPLACE AIRBAG ECU ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)  

5.CHECK INSTRUMENT PANEL WIRE


    C238259E14
  1. Disconnect the instrument panel wire from spiral cable sub-assembly.

  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      D52-3 (D2+) - Body ground
      Ignition switch ON
      Below 1 V
      D52-4 (D2-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check for an open in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D52-3 (D2+) - D52-4 (D2-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D52-3 (D2+) - Body ground
      Always
      1 MΩ or higher
      D52-4 (D2-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector B (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      D52-3 (D2+) - D52-4 (D2-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector B to the original condition.
      Text in Illustration 
      *1
      Horn Button Assembly
      *2
      Spiral Cable Sub-assembly
      *3
      Airbag ECU Assembly
      *4
      Instrument Panel Wire
      *a
      Front view of wire harness connector
      (to Spiral Cable Sub-assembly)



NG
REPLACE INSTRUMENT PANEL WIRE
OK


6.CHECK SPIRAL CABLE SUB-ASSEMBLY


    C259342E02
  1. Check for a short to B+ in the circuit.

    1. Connect the cable to the negative (-) battery terminal.

    2. Turn the ignition switch to ON.

    3. Measure the voltage according to the value(s) in the table below.

      Standard Voltage:
      Tester Connection
      Condition
      Specified Condition
      z6-1 (D2+) - Body ground
      Ignition switch ON
      Below 1 V
      z6-2 (D2-) - Body ground
      Ignition switch ON
      Below 1 V

    4. Turn the ignition switch off.

    5. Disconnect the cable from the negative (-) battery terminal.

      CAUTION:
      Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. Check for an open in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      z6-1 (D2+) - z6-2 (D2-)
      Always
      Below 1 Ω

  1. Check for a short to ground in the circuit.

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      z6-1 (D2+) - Body ground
      Always
      1 MΩ or higher
      z6-2 (D2-) - Body ground
      Always
      1 MΩ or higher

  1. Check for a short in the circuit.

    1. Release the activation prevention mechanism built into connector D (Click here).

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Condition
      Specified Condition
      z6-1 (D2+) - z6-2 (D2-)
      Always
      1 MΩ or higher

    3. Restore the released activation prevention mechanism of connector D to the original condition.
      Text in Illustration 
      *1
      Horn Button Assembly
      *2
      Spiral Cable Sub-assembly
      *3
      Airbag ECU Assembly
      *4
      Instrument Panel Wire
      *a
      Front view of wire harness connector
      (to Horn Button Assembly)
      *b
      Color: Black



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)