Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

DTC    P0191    Fuel Rail Pressure Sensor Circuit Range / Performance

DTC    P0192    Fuel Rail Pressure Sensor Circuit Low Input

DTC    P0193    Fuel Rail Pressure Sensor Circuit High Input

for Preparation Click here


DESCRIPTION

The fuel pressure sensor is installed on the delivery pipe. The sensor changes fuel pressure to an electrical signal and sends the signal to the ECM. Then the ECM controls the pump discharge using this feedback to maintain the fuel's target pressure. If the sensor output stops, the ECM will stop the high pressure side fuel pump and supply fuel using the low pressure side fuel pump.

DTC No.
DTC Detection Condition
Trouble Area
P0191
One of the following conditions is met (2 trip detection logic):
  1. Fuel pressure is 1.9 MPa or more 5 hours or more after ignition switch turned off.
  2. Fuel pressure is 1.84 MPa or less for 10 seconds or more with engine running when 5 hours or more elapsed after ignition switch turned off.
  1. Open or short in fuel pressure sensor circuit
  2. Fuel pressure sensor
  3. ECM
P0192
Fuel pressure sensor voltage is too low for 2.5 seconds or more.
(1 trip detection logic)
  1. Short in fuel pressure sensor circuit
  2. Fuel pressure sensor
  3. ECM
P0193
Fuel pressure sensor voltage is too high for 2.5 seconds or more.
(1 trip detection logic)
  1. Open in fuel pressure sensor circuit
  2. Fuel pressure sensor
  3. ECM

HINT:
After confirming DTC P0192 or P0193, use the GTS to confirm the fuel pressure in the delivery pipe by entering the following menus: Powertrain / Engine / Data List / Fuel Press.


Fuel Pressure (kPa)
Malfunction
Approximately 0
  1. PR and/or E1 circuit short
Approximately 26000
  1. PR and/or VC circuit short

MONITOR DESCRIPTION

These DTCs are set if the fuel pressure sensor output voltage is out of the standard range. The DTCs stand for an open or short malfunction of the sensor circuit.
If these DTCs are set, the ECM enters fail-safe mode and limits the engine power. Fail-safe mode continues until the ignition switch is turned off.

CONFIRMATION DRIVING PATTERN

  1. P0191


    1. A282259E01

    2. Connect the GTS to the DLC3.
    3. Turn the ignition switch to ON and turn the GTS on.
    4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
    5. Turn the ignition switch off and wait for at least 30 seconds.
    6. Turn the ignition switch to ON.
    7. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
    8. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more.
    9. Drive the vehicle at 30 km/h (18.75 mph) or more for 1 minute or more [A].

      CAUTION:
      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    10. Turn the ignition switch off and leave vehicle for 5 hours or more [B].
    11. Turn the ignition switch to ON and turn the GTS on.
    12. Enter the following menus: Powertrain / Engine / Trouble Codes.
    13. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
    14. Drive the vehicle at 30 km/h (18.75 mph) or more for 1 minute or more [C].

      CAUTION:
      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    15. Read pending DTCs.

      HINT:
      1. If a pending DTC is output, the system is malfunctioning.
      2. If a pending DTC is not output, perform the following procedure.

    16. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
    17. Input the DTC: P0191.
    18. Check the DTC judgment result.

      GTS Display
      Description
      NORMAL
      1. DTC judgment completed
      2. System normal
      ABNORMAL
      1. DTC judgment completed
      2. System abnormal
      INCOMPLETE
      1. DTC judgment not completed
      2. Perform driving pattern after confirming DTC enabling conditions
      N/A
      1. Unable to perform DTC judgment
      2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

      HINT:
      1. If the judgment result shows NORMAL, the system is normal.
      2. If the judgment result shows ABNORMAL, the system has a malfunction.

    19. If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

      HINT:
      1. If a permanent DTC is output, the system is malfunctioning.
      2. If no permanent DTC is output, the system is normal.

  1. P0192, P0193


    1. A283032E01

    2. Connect the GTS to the DLC3.
    3. Turn the ignition switch to ON and turn the GTS on.
    4. Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (Click here).
    5. Turn the ignition switch off and wait for at least 30 seconds.
    6. Turn the ignition switch to ON and turn the GTS on.
    7. Start the engine and warm it up until the engine coolant temperature reaches 75°C (167°F) or higher.
    8. With the vehicle stationary, depress the accelerator pedal and maintain an engine speed of between 2500 and 3000 rpm for 40 seconds or more [A].
    9. Drive the vehicle at 10 km/h (6.25 mph) or more for 1 minute or more [B].

      CAUTION:
      When performing the confirmation driving pattern, obey all speed limits and traffic laws.

    10. Enter the following menus: Powertrain / Engine / Trouble Codes.
    11. Read pending DTCs.

      HINT:
      1. If a pending DTC is output, the system is malfunctioning.
      2. If a pending DTC is not output, perform the following procedure.

    12. Enter the following menus: Powertrain / Engine / Utility / All Readiness.
    13. Input the DTC: P0192 or P0193.
    14. Check the DTC judgment result.

      GTS Display
      Description
      NORMAL
      1. DTC judgment completed
      2. System normal
      ABNORMAL
      1. DTC judgment completed
      2. System abnormal
      INCOMPLETE
      1. DTC judgment not completed
      2. Perform driving pattern after confirming DTC enabling conditions
      N/A
      1. Unable to perform DTC judgment
      2. Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit

      HINT:
      1. If the judgment result shows NORMAL, the system is normal.
      2. If the judgment result shows ABNORMAL, the system has a malfunction.

    15. If the test result is INCOMPLETE or N/A and no DTC is output, perform a universal trip and check for permanent DTCs (Click here).

      HINT:
      1. If a permanent DTC is output, the system is malfunctioning.
      2. If no permanent DTC is output, the system is normal.


WIRING DIAGRAM


A280065E01


INSPECTION PROCEDURE

HINT:
Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.

1.READ VALUE USING GTS (FUEL PRESS)
  1. Connect the GTS to the DLC3.

  1. Start the engine.

  1. Turn the GTS on.

  1. Enter the following menus: Powertrain / Engine / Data List / Fuel Press.

  1. Read the values.

    Result:

    Fuel Pressure (kPa)
    Proceed to
    26000 or more
    A
    Approximately 0
    3000 to 5000*
    B

    HINT:
    *: The value must change when the engine is moving or stationary.



B
CHECK FOR INTERMITTENT PROBLEMS (Click here)
A


2.INSPECT FUEL PRESSURE SENSOR (FUEL PRESSURE SENSOR POWER SOURCE)


    A280089E01
  1. Disconnect the fuel pressure sensor connector.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C10-1 (VC) - Body ground
    Ignition switch ON
    4.5 to 5.5 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Pressure Sensor)



NG
Go to step 5
OK


3.INSPECT ECM (PR VOLTAGE)


    A280163E05
  1. Start the engine.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A34-9 (PR) - A36-29 (E1)
    Idling with warm engine
    1.0 to 1.7 V

    Text in Illustration 
    *a
    Component with harness connected
    (ECM)

HINT:
The fuel pressure in the delivery pipe is 3 to 5 MPa.



NG
Go to step 4
OK

REPLACE ECM (Click here)  

4.CHECK HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR)
  1. Disconnect the ECM connectors.

  1. Disconnect the fuel pressure sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A34-9 (PR) - C10-3 (PR)
    Always
    Below 1 Ω
    A36-29 (E1) - C10-2 (E2)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A34-9 (PR) or C10-3 (PR) - body ground
    Always
    10 kΩ or higher
    A34-29 (E1) or C10-2 (E2) - body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)
OK

REPLACE FUEL PRESSURE SENSOR (Click here)  

5.CHECK HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR)
  1. Disconnect the fuel pressure sensor connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    A36-19 (VC) - C10-1 (VC)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    A36-19 (VC) or C10-1 (VC) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - FUEL PRESSURE SENSOR)
OK

REPLACE ECM (Click here)