DTC P0191 Fuel Rail Pressure Sensor Circuit Range / Performance |
DTC P0192 Fuel Rail Pressure Sensor Circuit Low Input |
DTC P0193 Fuel Rail Pressure Sensor Circuit High Input |
| DTC No. | DTC Detection Condition | Trouble Area |
| P0191 | One of the following conditions is met (2 trip detection logic):
|
|
| P0192 | Fuel pressure sensor voltage is too low for 2.4 seconds or more. (1 trip detection logic) |
|
| P0193 | Fuel pressure sensor voltage is too high for 2.4 seconds or more. (1 trip detection logic) |
|
| Fuel Pressure (High) | Malfunction |
| Approximately 0 | Main and/or E1 circuit short |
| Approximately 26000 | Main and/or VC circuit short |

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| GTS Display | Description |
| NORMAL |
|
| ABNORMAL |
|
| INCOMPLETE |
|
| N/A |
|

| 1.READ VALUE USING GTS (FUEL PRESSURE (HIGH)) |
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Powertrain / Engine / Data List / Fuel Pressure (High).
Read the values.
| Fuel Pressure (High) | Proceed to |
| Approximately 0 | A |
| 26000 or more | |
| 3000 to 5000* | B |
|
| ||||
| A | |
| 2.INSPECT FUEL PRESSURE SENSOR (FUEL PRESSURE SENSOR POWER SOURCE) |
![]() |
Disconnect the fuel pressure sensor connector.
Turn the ignition switch to ON.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Switch Condition | Specified Condition |
| C46-4 (VC) - Body ground | Ignition switch ON | 4.5 to 5.5 V |
| *a | Front view of wire harness connector (to Fuel Pressure Sensor) |
|
| ||||
| OK | |
| 3.INSPECT ECM (TERMINAL VOLTAGE) |
![]() |
Start the engine.
Measure the voltage according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A34-9 - A36-29 (E1) | Idling with warm engine | 0.7 to 1.3 V |
| *a | Component with harness connected (ECM) |
|
| ||||
| OK | ||
| ||
| 4.CHECK HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR) |
Disconnect the ECM connectors.
Disconnect the fuel pressure sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A34-9 - C46-3 (VOUT1) | Always | Below 1 Ω |
| A36-29 (E1) - C46-2 (GND) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A34-9 or C46-3 (VOUT1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||
| 5.CHECK HARNESS AND CONNECTOR (ECM - FUEL PRESSURE SENSOR) |
Disconnect the ECM connector.
Disconnect the fuel pressure sensor connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| A36-19 (VC) - C46-4 (VC) | Always | Below 1 Ω |
| Tester Connection | Condition | Specified Condition |
| A36-19 (VC) or C46-4 (VC) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | ||
| ||