Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Start Function)

ENTRY AND START SYSTEM (for Start Function) > TERMINALS OF ECU

for Preparation Click here


HINT:
  1. For the layout of the certification ECU (smart key ECU assembly) (verification-related) terminals, refer to the following (Click here).
  2. For the layout of the ID code box (immobiliser code ECU) terminals, refer to the following (Click here).
  3. For the layout of the steering lock actuator assembly (steering lock ECU) terminals, refer to the following (Click here).


CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B264892E44

  1. Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    D41-4 (ACCD) - Body ground
    Output
    SB - Body ground
    ACC signal
    20°C (68°F)
    81.49 to 118.98 Ω
    ACC Relay Monitor
    D41-6 (IG1D) - Body ground
    Output
    W - Body ground
    IG1 signal
    20°C (68°F)
    40.74 to 54.49 Ω
    IG1 Relay Monitor (Outside)
    D41-25 (P) - D48- 11 (GND)*1
    Input
    Y - B
    Shift lever P position switch signal
    Shift lever in P → Shift lever not in P
    Below 200 Ω → 40 kΩ or higher
    Shift P Signal
    D41-26 (SLP) - D48- 11 (GND)
    Input
    LG - B
    Steering lock bar position signal
    Always
    10 kΩ or higher
    Steering Unlock Switch
    D41-27 (SPD) - Body ground
    Input
    P - Body ground
    Vehicle speed signal
    Always
    30 kΩ or higher
    Vehicle Speed
    D41-28 (SSW1) - Body ground
    Input
    P - Body ground
    SSW1 contact signal
    Engine switch pushed → Engine switch not pushed
    Below 1 Ω → 10 kΩ or higher
    Start Switch1
    D41-30 (SSW2) - Body ground
    Input
    BE - Body ground
    SSW2 contact signal (backup for SSW1 and has same behavior as SSW1)

    HINT:
    Backup for SSW1. Behaves the same way as SSW1.

    Engine switch pushed → Engine switch not pushed
    Below 1 Ω → 10 kΩ or higher
    Start Switch2
    D48-11 (GND) - Body ground
    -
    B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    D48-9 (IG2D) - Body ground
    Output
    V - Body ground
    IG2 signal
    20°C (68°F)
    74.15 to 460.88 Ω
    IG2 Relay Monitor (Outside)
    D48-2 (+B) - Body ground
    Input
    R - Body ground
    +B power supply
    Always
    11 to 14 V
    -
    D48-17 (TACH) - Body ground
    Input
    GR - Body ground
    Engine speed signal
    Always
    10 kΩ or higher
    Engine Condition
    D48-18 (STP1) - Body ground*1
    Input
    L - Body ground
    Stop light switch signal
    Brake pedal depressed → Brake pedal released
    9 V or higher → 1 V or less
    Stop Light Switch1

    1. *1: for Automatic Transmission
    2. *2: for Manual Transaxle
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    D41-25 (P) - D48-11 (GND)*1
    Input
    Y - B
    Shift lever P position switch signal
    Shift lever in P →Shift lever not in P
    1.5 V or less → 9 V or higher
    Shift P Signal
    D41-4 (ACCD) - D48-11 (GND)
    Output
    SB - B
    ACC signal
    Engine switch off → Engine switch on (ACC)
    1 V or less → 8.5 V or higher
    ACC Relay Monitor
    D41-6 (IG1D) - D48-11 (GND)
    Output
    W - B
    IG1 signal
    Engine switch on (ACC) → Engine switch on (IG)
    1 V or less → 9 V or higher
    IG1 Relay Monitor(Outside)
    D41-26 (SLP) - D48-11 (GND)
    Input
    LG - B
    Steering lock bar position signal
    Steering locked → Steering unlocked*3
    11 to 14 V → 1.2 V or less
    Steering Unlock Switch
    D41-27 (SPD) - D48-11 (GND)
    Input
    P - B
    Vehicle speed signal
    Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)
    Pulse generation
    (See waveform 1)
    Vehicle Speed
    D41-28 (SSW1) - D48-11 (GND)
    Input
    P - B
    Engine switch signal
    Engine switch not pushed → Engine switch pushed
    9 V or higher → 1 V or less
    Start Switch1
    D41-29 (SLR+) - D48-11 (GND)
    Output
    Y - B
    Steering lock motor activation command signal (motor activation permission signal sent from certification ECU (smart key ECU assembly))
    Steering lock motor operating → Steering lock motor not operating → Steering lock motor operating*4
    Pulse generation
    (See waveform 2)
    -
    D41-30 (SSW2) - D48-11 (GND)
    Input
    BE - B
    SSW2 contact signal

    HINT:
    Backup for SSW1. Behaves the same way as SSW1.

    Engine switch not pushed → Engine switch pushed
    9 V or higher → 1 V or less
    Start Switch2
    D48-7 (STSW) - D48-11 (GND)
    Output
    P - B
    Starter request signal
    With the brake pedal*1 or clutch pedal*2 depressed, the engine switch is pressed and held (starter on) → After approx. 1 sec. has elapsed, the engine switch is released (starter off)
    2 V or less → 9 V or higher
    Starter Request Signal
    D48-5 (N-SW) - Body ground*1
    Input
    W - Body ground
    Neutral switch signal
    Engine switch on (IG), shift lever in P or N → Engine switch on (IG), shift lever not in P or N
    9 V or higher → 1 V or less
    Neutral SW/ Clutch SW
    D48-10 (CLUT) - Body ground*2
    Input
    Y - Body ground
    Clutch switch signal
    Perform the following operations except while the engine is cranking:
    Clutch pedal released → Clutch pedal depressed
    1 V or less → 9 V or higher
    Neutral SW/ Clutch SW
    D40-28 (ACCR) - D48-11 (GND)
    Input
    BE - B
    ACC relay cut signal
    With the brake pedal*1 or clutch pedal*2 depressed, the engine switch is pressed and held (starter on) → After approx. 1 sec. has elapsed, the engine switch is released (starter off)
    2 V or less → 9 V or higher
    ACC Relay Cut Signal
    D48-17 (TACH) - D48-11 (GND)
    Input
    GR - B
    Crankshaft position sensor signal
    Idling with warm engine
    Pulse generation
    (See waveform 3)
    Engine Condition
    D48-9 (IG2D) - D48-11 (GND)
    Output
    V - B
    IG2 signal
    Engine switch on (ACC) → Engine switch on (IG)
    1 V or less → 9 V or higher
    IG2 Relay Monitor(Outside)
    D48-18 (STP1) - D48-11 (GND)*1
    Input
    L - B
    Stop light switch signal
    Brake pedal released → Brake pedal depressed
    1 V or less → 9 V or higher
    Stop Light Switch1

    1. *1: for Automatic Transmission
    2. *2: for Manual Transaxle

    HINT:
    1. *3: When the shift lever is in P (for Automatic Transmission) and the engine switch is off, if any door is opened or closed, the steering is locked. When the key is inside the vehicle and the engine switch is turned on (ACC) or on (IG), the steering unlocks.
    2. *4: The steering lock motor operates when the following conditions are met and a door is opened:
      1. The shift lever is in P (for Automatic Transmission).
      2. While carrying the electrical key transmitter sub-assembly, the engine switch is turned on (IG) to unlock the steering, and then the engine switch is turned off.



  5. Using an oscilloscope, check the waveform of the ECU.

    NOTICE:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B220145E01
    1. Waveform 1 (Reference)
      Item
      Content
      Tester Connection
      D41-27 (SPD) - D48-11 (GND)
      Tool Setting
      5 V/DIV., 100 ms./DIV.
      Condition
      Engine switch on (IG), vehicle being driven at approx. 5 km/h (3 mph)

      HINT:
      The wavelength becomes shorter as the vehicle speed increases.



    2. C221561E01
    3. Waveform 2 (Reference)
      Item
      Content
      Tester Connection
      D41-29 (SLR+) - D48-11 (GND)
      Tool Setting
      2 V/DIV., 200 ms./DIV.
      Condition
      Steering lock motor not operating → Steering lock motor operating → Steering lock motor not operating*1
      Text in Illustration 
      *a
      Steering lock motor not operating
      *b
      Steering lock motor operating

      HINT:
      *1: When all of the following conditions are met, open any of the doors to operate the steering lock motor.
      1. The shift lever is in P*.
        1. *: for Automatic Transmission
      2. While carrying the electrical key transmitter sub-assembly, the engine switch is turned on (IG) and the steering wheel is unlocked.
      3. The engine switch is off.



    4. C222647E01
    5. Waveform 3 (Reference)
      Item
      Content
      Tester Connection
      D48-17 (TACH) - D48-11 (GND)
      Tool Setting
      2 V/DIV., 2 ms./DIV.
      Condition
      Idling with warm engine

      HINT:
      The wavelength becomes shorter as the engine speed increases.


CHECK ECM

A281924E01

  1. Measure the resistance and voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item/DTC
    A36-4 (E01) - Body ground
    -
    B-L - Body ground
    Ground
    Always
    Below 1 Ω
    -
    A33-14 (STSW2) - A36-4 (E01)
    Input
    BR - B-L
    Starter switch signal
    Engine switch on (IG)
    1 V or less
    Starter Control
    Cranking
    6 to 13 V
    A33-16 (NSW) - A36-4 (E01)
    Input
    W-R - B-L*1
    G-B - B-L*2
    Neutral switch signal
    Engine switch on (IG), shift lever in not P or N
    10 to 13 V
    -
    Engine switch on (IG), shift lever in P or N
    1 V or less
    A33-17 (STSW) - A36-4 (E01)
    Input
    G-W - B-L
    Starter request signal
    Engine switch on (IG)
    1 V or less
    -
    Cranking
    6 V or higher
    A35-15 (TACH) - A36-4 (E01)
    Output
    GR-R - B-L
    Engine speed signal
    Idling with warm engine
    Pulse generation
    (See waveform 1)
    Engine Speed
    A35-26 (STA) - A36-4 (E01)
    Output
    B-L - B-L*3
    B-W - B-L*4
    Starter relay signal
    Engine switch on (IG)
    11 to 14 V → 1 V or less
    Starter Signal
    Cranking
    10 to 13 V
    A35-32 (ACCR) - A36-4 (E01)
    Output
    G-Y - B-L
    ACC relay cut signal
    Engine switch on (IG)
    10 to 13 V
    -
    Cranking
    1 V or less
    A35-34 (STAR) - A36-4 (E01)
    Output
    LG-R - B-L
    Starter relay cut signal
    Engine switch on (IG)
    10 to 13 V
    Starter Cut Relay
    Cranking
    1 V or less

    1. *1: for Automatic Transmission
    2. *2: for Manual Transmission
    3. *3: w/ Double Locking Function
    4. *4: w/o Double Locking Function
    If the result is not as specified, the ECM may have a malfunction.



  2. Inspect using an oscilloscope.

    NOTICE:
    The waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      C222647E01
    1. Waveform 3 (Reference)
      Item
      Content
      Tester Connection
      A35-15 (TACH) - A36-4 (E01)
      Tool Setting
      2 V/DIV., 2 ms./DIV.
      Condition
      Idling with warm engine

      HINT:
      The wavelength becomes shorter as the engine speed increases.