Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)

ENTRY AND START SYSTEM (for Entry Function) > TERMINALS OF ECU

for Preparation Click here



CHECK CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

B264892E44

  1. Disconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    HINT:
    Measure the values on the wire harness side with the connector disconnected.


    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    D48-2 (+B) - D48-11 (GND)
    Input
    R - B
    +B power supply
    Always
    9.5 to 16 V
    -
    D48-11 (GND) - Body ground
    -
    B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    If the result is not as specified, there may be a malfunction on the wire harness side or the fuse is removed.

  3. Reconnect the D41 and D48 certification ECU (smart key ECU assembly) connectors.

  4. Measure the voltage according to the value(s) in the table below.

    HINT:
    1. Check that the entry cancel function, which is one of the customizing settings of the entry and start system, is not set (Click here).
    2. Check that the customizing setting "Ignition Available Area" of entry and start system is All (Click here).


    Tester Connection
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    D41-5 (IG2) - D48-11 (GND)
    Input
    Y - B
    IG power supply
    Engine switch off → on (IG)
    Below 1 V → 11 to 14 V
    Ignition Switch
    D41-12 (CLG1) - D48-11 (GND)
    Output
    Y - B
    Output to driver door electrical key antenna
    (request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought inside detection area*1
    6. All doors locked through wireless operation
    Pulse generation (See waveform 1)
    Over Head + Driver Side (key diagnostic mode)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought outside detection area*2
    6. All doors locked through wireless operation
    Pulse generation (See waveform 2)
    Over Head + Driver Side (key diagnostic mode)
    D41-13 (CG1B) - D48-11 (GND)
    Output
    BR - B
    Output to driver door electrical key antenna (terminal on opposite side of component from CLG1 output terminal)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. All doors locked through wireless operation
    Pulse generation (See waveform 2)
    Over Head + Driver Side (key diagnostic mode)
    D41-11 (CLG2) - D48-11 (GND)
    Output
    P - B
    Output to front passenger door electrical key antenna
    (request signal (challenge) is sent to door electrical key antenna from certification ECU (smart key ECU assembly) to form detection area)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought inside detection area*1
    6. All doors locked through wireless operation
    Pulse generation (See waveform 1)
    Over Head + Passenger Side (key diagnostic mode)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought outside detection area*2
    6. All doors locked through wireless operation
    Pulse generation (See waveform 2)
    Over Head + Passenger Side (key diagnostic mode)
    D41-10 (CG2B) - D48-11 (GND)
    Output
    V - B
    Output to front passenger door electrical key antenna (terminal on opposite side of component from CLG2 output terminal)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. All doors locked through wireless operation
    Pulse generation (See waveform 2)
    Over Head + Passenger Side (key diagnostic mode)
    D41-3 (CLG5) - D48-11 (GND)
    Output
    BE - B
    Output to indoor electrical key oscillator (front floor)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    Pulse generation (See waveform 3)
    Over Head + Front Room (key diagnostic mode)
    D41-2 (CG5B) - D48-11 (GND)
    Output
    P - B
    Output to indoor electrical key oscillator (front floor) (terminal on opposite side of component from CLG5 output terminal)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    Pulse generation (See waveform 3)
    Over Head + Front Room (key diagnostic mode)
    D41-20 (TSW1) - D48-11 (GND)
    Input
    G - B
    Driver door lock sensor signal input
    (Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) send 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded.
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Driver door lock sensor not touched → touched
    Pulse generation (See waveform 4)
    D-Door Trigger Switch
    D41-8 (TSW2) - D48-11 (GND)
    Input
    L - B
    Front passenger door lock sensor signal input
    (Sends signal from door lock sensor on front door outside handle assembly to certification ECU (smart key ECU assembly). Certification ECU (smart key ECU assembly) sends 12 V pulse waveform every 40 ms. from terminal TSW. When door lock sensor is touched, the pulse is grounded.
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Front passenger door lock sensor not touched → touched
    Pulse generation (See waveform 4)
    P-Door Trigger Switch
    D41-22 (SEN1) - D48-11 (GND)
    Input
    L - B
    Driver door unlock sensor signal input
    (when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly))
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors locked
    4. Electrical key transmitter sub-assembly not sufficiently close to vehicle
    5. Driver door unlock sensor not touched → touched
    Pulse generation (See waveform 4)
    D-Door Touch Sensor
    D41-23 (SEN2) - D48-11 (GND)
    Input
    W - B
    Front passenger door unlock sensor signal input
    (when system is in unlock standby mode and touch sensor is touched, door electrical key antenna sends touch sensor input signal (sensing) to certification ECU (smart key ECU assembly))
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors locked
    4. Electrical key transmitter sub-assembly not sufficiently close to vehicle
    5. Front passenger door unlock sensor not touched → touched
    Pulse generation (See waveform 4)
    P-Door Touch Sensor
    D40-27 (TSW5) - D48-11 (GND)
    Input
    Y - B
    Back door opener switch signal input
    Back door opener switch assembly off → on
    Pulse generation (See waveform 4)
    Tr/B-Door Unlock SW
    D40-11 (CLG6) - D48-11 (GND)
    Output
    W - B
    Output to No. 2 indoor electrical key oscillator (rear floor)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    Pulse generation (See waveform 3)
    Over Head + Rear Room (key diagnostic mode)
    D40-10 (CG6B) - D48-11 (GND)
    Output
    B - B
    Output to No. 2 indoor electrical key oscillator (rear floor) (terminal on opposite side of component from CLG6 output terminal)
    Proceed:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    Pulse generation (See waveform 3)
    Over Head + Rear Room (key diagnostic mode)
    D40-9 (CLG7) - D48-11 (GND)
    Output
    W - B
    Output to No. 3 indoor electrical key oscillator (inside luggage compartment)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    Pulse generation (See waveform 3)
    Over Head + Luggage (inside) (key diagnostic mode)
    D40-8 (CG7B) - D48-11 (GND)
    Output
    R - B
    Output to No. 3 indoor electrical key oscillator (inside luggage compartment) (terminal on opposite side of component from CLG7 output terminal)
    Proceed:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds
    Pulse generation (See waveform 3)
    Over Head + Luggage (inside) (key diagnostic mode)
    D41-19 (POS1) - D48-11 (GND)
    Output
    V - B
    Driver door unlock sensor power source (12 V (drops when engine switch turned on (IG)))
    Engine switch off → on (IG)
    9 to 14 V → Below 2 V
    -
    D41-21 (POS2) - D48-11 (GND)
    Output
    R - B
    Front passenger door unlock sensor power source (12 V (drops when engine switch turned on (IG)))
    Engine switch off → on (IG)
    9 to 14 V → Below 2 V
    -
    D40-5 (RCO) - D48-11 (GND)
    Output
    LG - B
    Output to door control receiver
    (Power supply for door control receiver. Certification ECU (smart key ECU assembly) outputs 5 V when receiver starts operating.)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3
    4. Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed
    Pulse generation (See waveform 5)
    -
    D40-17 (RDA) - D48-11 (GND)
    Input
    P - B
    Door control receiver verifies data received from electrical key transmitter sub-assembly. Door control receiver sends data to ECU and intermittently grounds 12 V signal from certification ECU (smart key ECU assembly).
    Proceed:
    1. Engine switch off
    2. All doors locked
    3. Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3
    4. Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed
    Pulse generation (See waveform 6)
    -
    D40-19 (RSSI) - D48-11 (GND)
    Input
    R - B
    Communication channel switching circuit.
    Proceed:
    1. Engine switch off
    2. All doors locked
    3. Electrical key transmitter sub-assembly brought outside detection area*2 but kept inside wireless function operational area*3
    4. Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed
    Pulse generation (See waveform 7)
    -
    D40-2 (CLG8) - D48-11 (GND)
    Output
    BR - B
    Output to electrical key antenna (outside luggage)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Back door opener switch assembly off → on
    Pulse generation (See waveform 8)
    Over Head + Luggage
    or
    Luggage + Luggage (key diagnostic mode)
    D40-1 (CG8B) - D48-11 (GND)
    Output
    Y - B
    Output to electrical key antenna (outside luggage) (terminal on opposite side of component from CLG8 output terminal)
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Back door opener switch assembly off → on
    Pulse generation (See waveform 8)
    Over Head + Luggage
    or
    Luggage + Luggage (key diagnostic mode)
    1. *1: For details about the areas that are inside the entry function detection area, refer to Operation Check (Click here).
    2. *2: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).
    3. *3: For details about the areas that are inside the wireless function operational area, refer to Operation Check (Click here).



  5. B251021E01
  6. Using an oscilloscope, check waveform 1.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Waveform 1 (Reference) 
    Item
    Content
    Tester Connection
    1. D41-12 (CLG1) - D48-11 (GND)
    2. D41-11 (CLG2) - D48-11 (GND)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought inside detection area*
    6. All doors locked through wireless operation
    1. *: For details about the areas that are inside the entry function detection area, refer to Operation Check (Click here).



  7. B251024E01
  8. Using an oscilloscope, check waveform 2.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Waveform 2 (Reference) 
    Item
    Content
    Tester Connection
    1. D41-12 (CLG1) - D48-11 (GND)
    2. D41-11 (CLG2) - D48-11 (GND)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought outside detection area*
    6. All doors locked through wireless operation
    1. *: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).
    Waveform 2 (Reference) 
    Item
    Content
    Tester Connection
    1. D41-13 (CG1B) - D48-11 (GND)
    2. D41-10 (CG2B) - D48-11 (GND)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. All doors locked through wireless operation
    1. *: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).



  9. B251020E01
  10. Using an oscilloscope, check waveform 3.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Text in Illustration 
    *a
    Door open
    *b
    After approximately 30 seconds from when the door is closed
    Waveform 3 (Reference) 
    Item
    Content
    Tester Connection
    1. D41-3 (CLG5) - D48-11 (GND)
    2. D41-2 (CG5B) - D48-11 (GND)
    3. D40-11 (CLG6) - D48-11 (GND)
    4. D40-10 (CG6B) - D48-11 (GND)
    5. D40-9 (CLG7) - D48-11 (GND)
    6. D40-8 (CG7B) - D48-11 (GND)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly not inside vehicle
    3. Door is open
    4. Door is closed
    5. Within 30 seconds



  11. B251023E01
  12. Using an oscilloscope, check waveform 4.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Text in Illustration 
    *a
    In actuality, sampling is being performed
    Waveform 4 (Reference) 
    Item
    Content
    Tester Connection
    D41-20 (TSW1) - D48-11 (GND)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Driver door lock sensor not touched → touched
    Waveform 4 (Reference) 
    Item
    Content
    Tester Connection
    D41-8 (TSW2) - D48-11 (GND)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Front passenger door lock sensor not touched → touched
    Waveform 4 (Reference) 
    Item
    Content
    Tester Connection
    D41-22 (SEN1) - D48-11 (GND)
    Tool Setting
    2 V/DIV., 500 ms/DIV
    Condition
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors locked
    4. Electrical key transmitter sub-assembly not sufficiently close to vehicle
    5. Driver door unlock sensor not touched → touched
    Waveform 4 (Reference) 
    Item
    Content
    Tester Connection
    D41-23 (SEN2) - D48-11 (GND)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors locked
    4. Electrical key transmitter sub-assembly not sufficiently close to vehicle
    5. Front passenger door unlock sensor not touched → touched
    Waveform 4 (Reference) 
    Item
    Content
    Tester Connection
    D40-27 (TSW5) - D48-11 (GND)
    Tool Setting
    2 V/DIV., 500 ms/DIV
    Condition
    Back door opener switch assembly off → on



  13. B251178E01
  14. Using an oscilloscope, check waveform 5.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Text in Illustration 
    *a
    Before lock or unlock button of electrical key transmitter sub-assembly pressed
    *b
    After lock or unlock button of electrical key transmitter sub-assembly pressed
    Waveform 5 (Reference) 
    Item
    Content
    Tester Connection
    D40-5 (RCO) - D48-11 (GND)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2
    4. Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed
    1. *1: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).
    2. *2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (Click here).



  15. B251177E01
  16. Using an oscilloscope, check waveform 6.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Text in Illustration 
    *a
    Before lock or unlock button of electrical key transmitter sub-assembly pressed
    *b
    After lock or unlock button of electrical key transmitter sub-assembly pressed
    Waveform 6 (Reference) 
    Item
    Content
    Tester Connection
    D40-17 (RDA) - D48-11 (GND)
    Tool Setting
    5 V/DIV., 500 ms/DIV.
    Condition
    Proceed:
    1. Engine switch off
    2. All doors locked
    3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2
    4. Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed
    1. *1: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).
    2. *2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (Click here).



  17. B251070E03
  18. Using an oscilloscope, check waveform 7.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Text in Illustration 
    *a
    Before lock or unlock button of electrical key transmitter sub-assembly pressed
    *b
    After lock or unlock button of electrical key transmitter sub-assembly pressed
    Waveform 7 (Reference) 
    Item
    Content
    Tester Connection
    D40-19 (RSSI) - D48-11 (GND)
    Tool Setting
    5 V/DIV., 500 ms/DIV.
    Condition
    Proceed:
    1. Engine switch off
    2. All doors locked
    3. Electrical key transmitter sub-assembly brought outside detection area*1 but kept inside wireless function operational area*2
    4. Lock or unlock button of electrical key transmitter sub-assembly not pressed → pressed
    1. *1: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).
    2. *2: For details about the areas that are inside the wireless function operational area, refer to Operation Check (Click here).



  19. B265917E01
  20. Using an oscilloscope, check waveform 8.

    HINT:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.

    Text in Illustration 
    *a
    Engine switch off, all doors closed and back door opener switch assembly off → on
    Waveform 8 (Reference) 
    Item
    Content
    Tester Connection
    1. D40-2 (CLG8) - D48-11 (GND)
    2. D40-1 (CG8B) - D48-11 (GND)
    Tool Setting
    2 V/DIV., 500 ms/DIV.
    Condition
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Back door opener switch assembly off → on


CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (NETWORK GATEWAY ECU)

B311498E01


Text in Illustration 
*1
Instrument Panel Junction Block Assembly
*2
Main Body ECU (Network Gateway ECU)
  1. Remove the main body ECU (network gateway ECU) from the instrument panel junction block assembly (Click here).

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    MB-1 (BECU) - Body ground
    Input
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    -
    MB-8 (IG) - Body ground
    Input
    None - Body ground
    Engine switch power supply
    Engine switch on (IG)
    11 to 14 V
    IG SW
    Engine switch off
    Below 1 V
    MB-9 (ACC) - Body ground
    Input
    None - Body ground
    ACC power supply
    Engine switch on (ACC)
    11 to 14 V
    ACC SW
    Engine switch off
    Below 1 V
    MB-11 (GND) - Body ground
    Input
    None - Body ground
    Ground
    Always
    Below 1 Ω
    -
    MB-32 (BMPX) - Body ground
    Input
    None - Body ground
    Battery power supply
    Always
    11 to 14 V
    -
    D6-1 (GND) - Body ground
    -
    B - Body ground
    Ground
    Always
    Below 1 Ω
    -
    A73-4 (GND) - Body ground
    -
    B-Y - Body ground
    Ground
    Always
    Below 1 Ω
    -
    If the result is not as specified, there may be a malfunction in the wire harness.

  3. Install the main body ECU (network gateway ECU) to the instrument panel junction block assembly (Click here).

  4. Measure the voltage and waveform according to the value(s) in the table below.

    Terminal No. (Symbol)
    Input/Output
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    Related Data List Item
    3A-28 - Body ground
    Input
    V - Body ground
    Driver side door courtesy light switch input
    Driver side door open
    Below 1 V
    D Door Courtesy SW
    Driver side door closed
    11 to 14 V
    3B-13 - Body ground
    Input
    GR - Body ground
    Passenger side door courtesy light switch input
    Passenger side door open
    Below 1 V
    P Door Courtesy SW
    Passenger side door closed
    11 to 14 V
    3D-26 - Body ground
    Input
    SB - Body ground
    Luggage compartment door courtesy light switch input
    Luggage compartment door open
    Below 1 V
    Luggage Courtesy SW
    Engine switch off, all doors closed and luggage compartment door closed
    11 to 14 V
    D5-22 (ACC) - Body ground
    Input
    W - Body ground
    ACC power supply
    Engine switch on (ACC)
    11 to 14 V
    ACC SW
    Engine switch off
    Below 1 V
    D5-11 (L2) - Body ground*1
    Input
    BE - Body ground
    Driver side door lock and unlock switch input
    Driver side door key cylinder in lock position
    Below 1 V
    -
    Engine switch off, all doors closed and driver side door key cylinder in neutral position
    Pulse generation (See waveform 1 or 2)
    D5-12 (UL2) - Body ground*1
    Input
    R - Body ground
    Driver side door lock and unlock switch input
    Driver side door key cylinder in unlock position
    Below 1 V
    -
    Engine switch off, all doors closed and driver side door key cylinder in neutral position
    Pulse generation (See waveform 1 or 2)
    3B-2 - Body ground
    Output
    V - Body ground
    Door lock motor lock drive output (for driver side)
    Driver side door control switch not pushed and driver side door key cylinder in neutral position*1
    Below 1 V
    -
    Lock side of driver side door control switch pushed or driver side door key cylinder in lock position*1
    11 to 14 V
    3B-3 - Body ground
    Output
    L - Body ground
    Door lock motor lock drive output (for passenger side)
    Driver side door control switch not pushed and driver side door key cylinder in neutral position*1
    Below 1 V
    -
    Lock side of driver side door control switch pushed or driver side door key cylinder in lock position*1
    11 to 14 V
    3B-6 - Body ground
    Output
    G - Body ground
    Door lock motor lock drive output (for luggage compartment door)
    Luggage open switch of electrical key transmitter sub-assembly not pressed
    Below 1 V
    Trunk and Back- Door Open
    Luggage open switch of electrical key transmitter sub-assembly pressed
    11 to 14 V
    3B-1 - Body ground
    Output
    R-G - Body ground
    Door lock motor unlock drive output (for driver side)
    Driver side door control switch not pushed and driver side door key cylinder in neutral position*
    Below 1 V
    -
    Unlock side of driver side door control switch pushed or driver side door key cylinder in unlock position*
    11 to 14 V
    3B-4 - Body ground
    Output
    L-W - Body ground
    Door lock motor unlock drive output (for passenger side)
    Driver side door control switch not pushed and driver side door key cylinder in neutral position*
    Below 1 V
    -
    Unlock side of driver side door control switch pushed or driver side door key cylinder in unlock position*
    11 to 14 V
    D6-11 (LSFD) - Body ground
    Input
    W - Body ground
    Driver side door unlock detection switch input
    Driver side door unlocked
    Below 1 V
    D-Door Lock Pos SW
    Engine switch off, all doors closed and driver side door locked
    Pulse generation (See waveform 1 or 2)
    D6-12 (LSFP) - Body ground
    Input
    SB - Body ground
    Passenger side door unlock detection switch input
    Passenger side door unlocked
    Below 1 V
    P-Door Lock Pos SW
    Engine switch off, all doors closed and passenger side door locked
    Pulse generation (See waveform 1 or 2)

    1. *: w/ Key-linked Switch



  5. Inspect using an oscilloscope.

    NOTICE:
    The oscilloscope waveform shown in the illustration is an example for reference only. Noise, chattering, etc. are not shown.




      B199631E02
    1. Waveform 1 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      D5-11 (L2) - Body ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Engine switch off, all doors closed and driver side door key cylinder in neutral position
      Measurement Condition 
      Item
      Content
      Tester Connection
      D5-12 (UL2) - Body ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Engine switch off, all doors closed and driver side door key cylinder in neutral position
      Measurement Condition 
      Item
      Content
      Tester Connection
      D6-11 (LSFD) - Body ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Engine switch off, all doors closed and driver side door locked
      Measurement Condition 
      Item
      Content
      Tester Connection
      D6-12 (LSFP) - Body ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Engine switch off, all doors closed and passenger side door locked



    2. B199632E04
    3. Waveform 2 (Reference)
      Measurement Condition 
      Item
      Content
      Tester Connection
      D5-11 (L2) - Body ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Engine switch off, all doors closed and driver side door key cylinder in neutral position
      Measurement Condition 
      Item
      Content
      Tester Connection
      D5-12 (UL2) - Body ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Engine switch off, all doors closed and driver side door key cylinder in neutral position
      Measurement Condition 
      Item
      Content
      Tester Connection
      D6-11 (LSFD) - Body ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Engine switch off, all doors closed and driver side door locked
      Measurement Condition 
      Item
      Content
      Tester Connection
      D6-12 (LSFP) - Body ground
      Tool Setting
      5 V/DIV., 20 ms/DIV.
      Condition
      Engine switch off, all doors closed and passenger side door locked