Home › Brake › BRAKE CONTROL / DYNAMIC CONTROL SYSTEMS › VEHICLE STABILITY CONTROL SYSTEM

VEHICLE STABILITY CONTROL SYSTEM > ABS Warning Light Remains ON

for Preparation Click here


DESCRIPTION

The skid control ECU (brake actuator assembly) is connected to the combination meter assembly via CAN communication.
If any of the following is detected, the ABS warning light remains on:
  1. The skid control ECU (brake actuator assembly) connector is disconnected from the skid control ECU (brake actuator assembly).
  2. There is a malfunction in the skid control ECU (brake actuator assembly) internal circuit.
  3. There is an open in the harness between the combination meter assembly and the skid control ECU (brake actuator assembly).
  4. The ABS control system is defective.

HINT:
In some cases, the GTS cannot be used when the skid control ECU (brake actuator assembly) is abnormal.


WIRING DIAGRAM


C264062E01


INSPECTION PROCEDURE

NOTICE:
  1. When replacing the skid control ECU (brake actuator assembly), perform VSC sensor neutral memorization (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK CAN COMMUNICATION SYSTEM
  1. Check if a CAN communication system DTC is output (Click here).

    Result:

    Result
    Proceed to
    DTC is not output.
    A
    DTC is output.
    B



B
INSPECT CAN COMMUNICATION SYSTEM (Click here)
A


2.CHECK IF BRAKE ACTUATOR ASSEMBLY CONNECTOR IS SECURELY CONNECTED
  1. Check if the skid control ECU (brake actuator assembly) connector is securely connected.

    OK:
    The connector is securely connected.



NG
CONNECT CONNECTOR TO ECU CORRECTLY
OK


3.CHECK BATTERY
  1. Check the battery voltage.

    Standard Voltage:
    11 to 14 V



NG
CHECK OR REPLACE CHARGING SYSTEM COMPONENT OR BATTERY (Click here)
OK


4.CHECK HARNESS AND CONNECTOR (POWER SOURCE TERMINAL)


    C261861E07
  1. Disconnect the skid control ECU (brake actuator assembly) connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A5-25 (+BS) - Body ground
    Always
    11 to 14 V
    A5-25 (+BS) - A5-38 (GND1)
    Always
    11 to 14 V
    A5-28 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V
    A5-28 (IG1) - A5-38 (GND1)
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)
OK


5.CHECK HARNESS AND CONNECTOR (GND1 TERMINAL)


    C261861E06
  1. Turn the ignition switch off.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A5-38 (GND1) - Body ground
    Always
    Below 1 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Skid Control ECU (Brake Actuator Assembly))



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (GND1 CIRCUIT)
OK


6.INSPECT COMBINATION METER ASSEMBLY
  1. Reconnect the skid control ECU (brake actuator assembly) connector.

  1. Perform an Active Test of the combination meter assembly (meter CPU) using the GTS (Click here).

  1. Check the combination meter assembly.

    OK:
    The ABS warning light turns on or off in accordance with the Active Test operation.

    HINT:
    If troubleshooting has been carried out according to Problem Symptoms Table, refer back to the table and proceed to the next step before replacing parts (Click here).



NG
REPLACE COMBINATION METER ASSEMBLY (Click here)
OK

REPLACE BRAKE ACTUATOR ASSEMBLY (Click here)