ENTRY AND START SYSTEM (for Entry Function) > Driver Side Door Entry Lock and Unlock Functions do not Operate |

| 1.CHECK POWER DOOR LOCK OPERATION |
When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to switch operation (Click here).
|
| ||||
| OK | |
| 2.CHECK WAVE ENVIRONMENT |
![]() |
Bring the electrical key transmitter sub-assembly near the front door outside handle assembly, and perform a driver door entry lock and unlock operation check.
| *A | for LHD |
| *B | for RHD |
| *a | Approximately 0.3 m (0.98 ft.) |
| Result | Proceed to |
| Entry functions operate abnormally | A |
| Entry functions operate normally | B |
|
| ||||
| A | |
| 3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY) |
Disconnect the D41 certification ECU (smart key ECU assembly) connector.
Disconnect the E1*1 or F5*2 front door outside handle assembly (for driver side door) connector.
Measure the resistance according to the value(s) in the table below.
| Tester Connection | Condition | Specified Condition |
| D41-12 (CLG1) - E1-6 (ANT1) | Always | Below 1 Ω |
| D41-13 (CG1B) - E1-3 (ANT2) | Always | Below 1 Ω |
| D41-19 (POS1) - E1-5 (B) | Always | Below 1 Ω |
| D41-12 (CLG1) - Body ground | Always | 10 kΩ or higher |
| D41-13 (CG1B) - Body ground | Always | 10 kΩ or higher |
| D41-19 (POS1) - Body ground | Always | 10 kΩ or higher |
| Tester Connection | Condition | Specified Condition |
| D41-12 (CLG1) - F5-6 (ANT1) | Always | Below 1 Ω |
| D41-13 (CG1B) - F5-3 (ANT2) | Always | Below 1 Ω |
| D41-19 (POS1) - F5-5 (B) | Always | Below 1 Ω |
| D41-12 (CLG1) - Body ground | Always | 10 kΩ or higher |
| D41-13 (CG1B) - Body ground | Always | 10 kΩ or higher |
| D41-19 (POS1) - Body ground | Always | 10 kΩ or higher |
|
| ||||
| OK | |
| 4.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO DRIVER SIDE DOOR ELECTRICAL KEY ANTENNA) |
Reconnect the D41 certification ECU (smart key ECU assembly) connector.
![]() |
Using an oscilloscope, check the waveform.
| *A | for LHD |
| *B | for RHD |
| *a | Front view of wire harness connector (to Front Door Outside Handle Assembly (for driver side door)) |
| *b | Waveform |
| Tester Connection | Condition | Tool Setting | Specified Condition |
| E1-6 (ANT1) - E1-3 (ANT2)*1 F5-6 (ANT1) - F5-3 (ANT2)*2 | Procedure:
| 5 V/DIV., 500 ms/DIV. | Pulse generation (See waveform) |
|
| ||||
| OK | |
| 5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE DOOR) |
Temporarily replace the front door outside handle assembly (for driver side door) with a new or known good one (Click here).
| NEXT | |
| 6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR DRIVER SIDE DOOR) (OPERATION) |
Check that the entry functions operate normally (Click here).
|
| ||||
| OK | ||
| ||