Home › Vehicle Interior › THEFT DETERRENT / KEYLESS ENTRY › ENTRY AND START SYSTEM (for Entry Function)

ENTRY AND START SYSTEM (for Entry Function) > Front Passenger Side Door Entry Lock and Unlock Functions do not Operate

for Preparation Click here


DESCRIPTION

If the entry lock and unlock functions do not operate for the front passenger door only, the request code may not be being transmitted from the front passenger door or the front door outside handle assembly (for front passenger door) (touch sensor) may be malfunctioning. If the entry functions for other doors operate properly, communication between the electrical key transmitter sub-assembly and door control receiver is normal. In this case, there may be a problem with request code transmission (communication between the certification ECU (smart key ECU assembly) and front door outside handle assembly (for front passenger door) [front passenger door electrical key antenna]), or there may be wave interference.

WIRING DIAGRAM


B312717E02


INSPECTION PROCEDURE

NOTICE:
  1. When using the GTS with the engine switch off to troubleshoot:
    Connect the GTS to the DLC3 and turn a courtesy light switch on and off at 1.5-second intervals until communication between the GTS and vehicle begins.
  2. The entry and start system (for Entry Function) uses a LIN communication system and CAN communication system. Inspect the communication function by following How to Proceed with Troubleshooting (Click here). Troubleshoot the entry and start system (for Entry Function) after confirming that the communication system is functioning properly.
  3. Before replacing the certification ECU (smart key ECU assembly), refer to the entry and start system (for Entry Function) (Click here).
  4. Check that there are no electrical key transmitter sub-assemblies in the vehicle.
  5. When checking the entry lock operation multiple times, the lock operation may be limited to 2 consecutive operations depending on the settings. In order to perform the entry lock operation 3 or more times, an unlock operation must be performed once (any type of unlock operation is sufficient). However, only consecutive entry lock operations are limited. Using the wireless lock or other types of lock operations, it is possible to perform consecutive lock operations without this limitation.

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the power window regulator master switch assembly is operated, check that the doors unlock and lock according to switch operation (Click here).

    OK:
    Door locks operate normally.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (PROCEED TO PROBLEM SYMPTOMS TABLE) (Click here)
OK


2.CHECK WAVE ENVIRONMENT


    B315532E01
  1. Bring the electrical key transmitter sub-assembly near the front door outside handle assembly, and perform a front passenger door entry lock and unlock operation check.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Approximately 0.3 m (0.98 ft.)

    NOTICE:
    If the key is brought within 0.2 m (0.656 ft.) of the door outside handle assembly, communication is not possible.

    HINT:
    1. When the electrical key transmitter sub-assembly is brought near the front door outside handle assembly, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the operation is normal, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.

    Result 
    Result
    Proceed to
    Entry functions operate abnormally
    A
    Entry functions operate normally
    B



B
AFFECTED BY WAVE INTERFERENCE
A


3.CHECK HARNESS AND CONNECTOR (CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) - FRONT DOOR OUTSIDE HANDLE ASSEMBLY
  1. Disconnect the D41 certification ECU (smart key ECU assembly) connector.

  1. Disconnect the F5*1 or E1*2 front door outside handle assembly (for passenger side door) connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    D41-11 (CLG2) - F5-6 (ANT1)
    Always
    Below 1 Ω
    D41-10 (CG2B) - F5-3 (ANT2)
    Always
    Below 1 Ω
    D41-21 (POS2) - F5-5 (B)
    Always
    Below 1 Ω
    D41-11 (CLG2) - Body ground
    Always
    10 kΩ or higher
    D41-10 (CG2B) - Body ground
    Always
    10 kΩ or higher
    D41-21 (POS2) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    D41-11 (CLG2) - E1-6 (ANT1)
    Always
    Below 1 Ω
    D41-10 (CG2B) - E1-3 (ANT2)
    Always
    Below 1 Ω
    D41-21 (POS2) - E1-5 (B)
    Always
    Below 1 Ω
    D41-11 (CLG2) - Body ground
    Always
    10 kΩ or higher
    D41-10 (CG2B) - Body ground
    Always
    10 kΩ or higher
    D41-21 (POS2) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4.INSPECT CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (OUTPUT TO FRONT PASSENGER DOOR ELECTRICAL KEY ANTENNA)
  1. Reconnect the D41 certification ECU (smart key ECU assembly) connector.



    B269122E02
  1. Using an oscilloscope, check the waveform.
    Text in Illustration 
    *A
    for LHD
    *B
    for RHD
    *a
    Front view of wire harness connector
    (to Front Door Outside Handle assembly)
    *b
    Waveform

    OK:

    Tester Connection
    Condition
    Tool Setting
    Specified Condition
    F5-6 (ANT1) - F5-3 (ANT2)*1
    E1-6 (ANT1) - E1-3 (ANT2)*2
    Procedure:
    1. Engine switch off
    2. Electrical key transmitter sub-assembly brought outside vehicle
    3. All doors closed
    4. Electrical key transmitter sub-assembly not inside vehicle
    5. Electrical key transmitter sub-assembly brought outside detection area*3
    6. All doors locked through wireless operation
    5 V/DIV., 500 ms/DIV.
    Pulse generation
    (See waveform)

    1. *1: for LHD
    2. *2: for RHD
    3. *3: For details about the areas that are outside the entry function detection area, refer to Operation Check (Click here).



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK


5.REPLACE FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR)
  1. Temporarily replace the front door outside handle assembly (for front passenger side door) with a new or known good one (Click here).


NEXT


6.CHECK FRONT DOOR OUTSIDE HANDLE ASSEMBLY (FOR PASSENGER SIDE DOOR) (OPERATION)
  1. Check that the entry functions operate normally (Click here).

    OK:
    Entry functions operate normally.



NG
REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)
OK

END (FRONT DOOR OUTSIDE HANDLE ASSEMBLY WAS DEFECTIVE)