Home › Vehicle Interior › DOOR LOCK › WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System)

WIRELESS DOOR LOCK CONTROL SYSTEM (w/o Entry and Start System) > Only Wireless Control Function is Inoperative

for Preparation Click here


DESCRIPTION

The door control receiver receives signals from the transmitter and sends these signals to the main body ECU (network gateway ECU). The main body ECU (network gateway ECU) then controls all doors by sending lock/unlock signals to each door.

WIRING DIAGRAM


B222320E05


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.CHECK POWER DOOR LOCK OPERATION
  1. When the door control switch on the power window regulator master switch assembly is operated, check that the locked doors unlock (Click here).

OK:
Locked doors unlock.



NG
GO TO POWER DOOR LOCK CONTROL SYSTEM (Click here)
OK


2.CHECK KEY REMINDER WARNING SYSTEM
  1. Check that the key reminder warning buzzer operates normally (Click here).

    OK:
    Key reminder warning buzzer operates normally.



NG
GO TO KEY REMINDER WARNING SYSTEM (Click here)
OK


3.SWITCH TO SELF DIAGNOSTIC MODE
  1. Switch to self-diagnostic mode by operating the ignition key cylinder.

    1. Insert the key into the ignition key cylinder and remove it.

    2. Within 5 seconds after the key is removed, insert it into the ignition key cylinder and then turn the ignition switch to ON then off once. (End in off)

    3. Within 30 seconds after turning the ignition switch off, perform the following 9 times: Turn the ignition switch to ON then off. (End in off)

      NOTICE:
      If the system fails to enter self-diagnostic mode, the system will return to normal mode.

      HINT:
      Turning the ignition switch to ON after the procedure above has been completed will end the self-diagnostic mode.



    B220865E09
  1. Check that the system has switched to self-diagnostic mode by checking the interior light output pattern.



    B220865E08
  1. Check that the system has switched to self-diagnostic mode by checking the wireless door lock buzzer output pattern (w/ Wireless Door Lock Buzzer Control Function).

OK:
Flash pattern is same as illustration on left.


NEXT


4.CHECK BY SELF DIAGNOSTIC MODE


  1. Check the diagnostic outputs when the door control transmitter module set sub-assembly switch is held down. The diagnostic outputs can be checked by the interior light and wireless door lock buzzer patterns.


    B163380E44


    Result 
    Result
    Proceed to
    Normal wave (light flash pattern and buzzer pattern) is output.
    A
    Unmatching recognition code is output.
    B
    No diagnosis outputs
    C



B
Go to step 5

C
Go to step 6
A

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)  

5.REGISTER RECOGNITION CODE
  1. Check that the system can be switched to rewrite mode or add mode, and that a recognition code can be registered.

    OK:
    Recognition code can be registered.



NG
REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY (Click here)
OK

END 

6.CHECK RESPONSE OF DOOR CONTROL RECEIVER (RESPONSE)
  1. Prepare the door control transmitter from another vehicle.

  1. Press and hold down the door control transmitter switch.

  1. Check that an unmatching recognition code is output.

OK:
Unmatching recognition code is output.



NG
Go to step 10
OK


7.INSPECT TRANSMITTER BATTERY (VOLTAGE)
B178438E07
  1. Remove the battery from the door control transmitter module that does not operate. Attach a lead wire (0.6 mm (0.0236 in.)) or less in diameter including wire sheath) with tape or equivalent to the negative terminal (Click here).

    NOTICE:
    Do not wrap the lead wire around the terminal, wedge it between terminals, or solder it. The terminal may be deformed or damaged, and the battery will not be able to be installed correctly.

    Text in Illustration 
    *1
    Lead Wire

  1. Carefully pull the lead wire out from the position shown in the illustration and install the previously removed transmitter battery.

    NOTICE:
    When replacing the transmitter battery, before starting work, remove any static electricity that has built up by touching, for example, the vehicle to prevent the door control transmitter module set from being damaged.



    B320719E01
  1. Measure the voltage according to the value(s) in the table below.

    HINT:
    When measuring the battery voltage, press one of the transmitter switches.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    Battery positive (+) - Battery negative (-)
    Ignition switch off, all doors closed and lock or unlock switch pushed
    2.5 to 3.2 V

    Text in Illustration 
    *a
    GND



NG
Go to step 8
OK

REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY (Click here)  

8.REPLACE TRANSMITTER BATTERY
  1. Replace the transmitter battery (Click here).


NEXT


9.CHECK BY SELF DIAGNOSTIC MODE


  1. Inspect the diagnostic outputs when the door control transmitter module set sub-assembly switch is held down. The diagnostic outputs can be checked by the flash patterns of the interior lights and the buzzer patterns of the wireless door lock buzzer.


    B163380E44


    Result 
    Result
    Proceed to
    Normal wave (light flash pattern and buzzer pattern) is output.
    A
    Unmatching recognition code is output
    B
    No diagnosis outputs



B
REPLACE DOOR CONTROL TRANSMITTER MODULE SET SUB-ASSEMBLY (Click here)
A

END (TRANSMITTER BATTERY IS DEFECTIVE) 

10.CHECK WAVE ENVIRONMENT
  1. Bring the transmitter near the door control receiver, and perform a wireless operation check.

    OK:
    Wireless functions operate normally.

    HINT:
    1. When the transmitter is brought near the door control receiver, the possibility of wave interference decreases, and it can be determined if wave interference is causing the problem symptom.
    2. If the inspection result is that the problem only occurs in certain locations or times of day, the possibility of wave interference is high. Also, added vehicle components may cause wave interference. If installed, remove them and perform the operation check.



NG
AFFECTED BY WAVE INTERFERENCE
OK


11.INSPECT DOOR CONTROL RECEIVER (POWER SOURCE, GROUND)
B159866E08
  1. Disconnect the H27 door control receiver connector.

  1. Measure the resistance and voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection
Condition
Specified Condition
H27-5 (+B) - Body ground
Always
11 to 14 V

Standard Resistance:
Tester Connection
Condition
Specified Condition
H27-1 (GND) - Body ground
Always
Below 1 Ω

Text in Illustration 
*a
Front view of wire harness connector
(to Door Control Receiver)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12.INSPECT DOOR CONTROL RECEIVER (OUTPUT)
B238267E07
  1. Reconnect the H27 door control receiver connector.

  1. Measure the voltage according to the value(s) in the table below.

Standard Voltage:
w/o Tire Pressure Warning System 
Tester Connection
Switch Condition
Specified Condition
H27-2 (RDA) - Body ground
Ignition switch off, all doors closed and door control transmitter switch off
11 to 14 V
Ignition switch off, all doors closed and door control transmitter switch on
pulse generation

Text in Illustration 
*a
Component with harness connected
(Door Control Receiver)


NG
REPLACE DOOR CONTROL RECEIVER (Click here)
OK


13.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - DOOR CONTROL RECEIVER)
  1. Disconnect the D6 main body ECU (network gateway ECU) connector.

  1. Disconnect the H27 door control receiver connector.

  1. Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Condition
Specified Condition
D6-7 (RDA) - H27-2 (RDA)
Always
Below 1 Ω
D6-7 (RDA) or H27-2 (RDA) - Body ground
Always
10 kΩ or higher
D6-6 (PRG) - H27-3 (PRG)
Always
Below 1 Ω
D6-6 (PRG) or H27-3 (PRG) - Body ground
Always
10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


14.REPLACE DOOR CONTROL RECEIVER
  1. Temporarily replace the door control receiver with a new or normally functioning one (Click here).


NEXT


15.REGISTER RECOGNITION CODE
  1. Perform the Registration procedures (Click here).


NEXT


16.CHECK DOOR CONTROL RECEIVER (OPERATION)
  1. Check that the doors can be locked and unlocked by using the transmitter LOCK and UNLOCK switches.

OK:
Doors can be locked and unlocked with transmitter.



NG
REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)
OK

END (DOOR CONTROL RECEIVER IS DEFECTIVE)