Home › Engine / Hybrid System › FA20 ENGINE CONTROL › SFI SYSTEM

SFI SYSTEM > Fuel Injector Circuit

for Preparation Click here


DESCRIPTION

The fuel injectors (for port injection) are attached to the intake manifold, and inject fuel into the intake manifold based on the ECM signals.

WIRING DIAGRAM


A280104E01


INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.

1.INSPECT FUEL INJECTOR ASSEMBLY (POWER SOURCE)


    A280161E01
  1. Disconnect the fuel injector assembly connectors.

  1. Turn the ignition switch to ON.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    C8-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C30-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C9-1 - Body ground
    Ignition switch ON
    11 to 14 V
    C31-1 - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Fuel Injector Assembly)
    *b
    No. 1 cylinder
    *c
    No. 2 cylinder
    *d
    No. 3 cylinder
    *e
    No. 4 cylinder



NG
Go to step 4
OK


2.INSPECT FUEL INJECTOR ASSEMBLY (INJECTION AND VOLUME)
  1. Check the fuel injector injection and volume (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
  1. Disconnect the fuel injector assembly connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    C8-2 - A36-12 (#10)
    Always
    Below 1 Ω
    C30-2 - A36-22 (#20)
    Always
    Below 1 Ω
    C9-2 - A36-32 (#30)
    Always
    Below 1 Ω
    C31-2 - A36-13 (#40)
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    C1-2 or A36-12 (#10) - Body ground
    Always
    10 kΩ or higher
    C2-2 or A36-22 (#20) - Body ground
    Always
    10 kΩ or higher
    C3-2 or A36-32 (#30) - Body ground
    Always
    10 kΩ or higher
    C8-2 or A36-13 (#40) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)  

4.CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - EFI MAIN1 RELAY)
  1. Disconnect the fuel injector assembly connector.

  1. Remove the EFI MAIN1 relay from the engine room relay block assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for open):

    Tester Connection
    Condition
    Specified Condition
    C8-1 - EFI MAIN1 relay terminal 3
    Always
    Below 1 Ω
    C30-1 - EFI MAIN1 relay terminal 3
    Always
    Below 1 Ω
    C9-1 - EFI MAIN1 relay terminal 3
    Always
    Below 1 Ω
    C31-1 - EFI MAIN1 relay terminal 3
    Always
    Below 1 Ω


    Standard Resistance (Check for short):

    Tester Connection
    Condition
    Specified Condition
    C8-1 or EFI MAIN1 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    C30-1 or EFI MAIN1 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    C9-1 or EFI MAIN1 relay terminal 3 - Body ground
    Always
    10 kΩ or higher
    C31-1 or EFI MAIN1 relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)