Home › Vehicle Exterior › LIGHTING (EXT) › LIGHTING SYSTEM

DTC    B1244    Light Sensor Circuit Malfunction

for Preparation Click here


DESCRIPTION

The automatic light control sensor detects ambient light, converts it into an electrical signal, and outputs it to the main body ECU (network gateway ECU). The main body ECU (network gateway ECU) turns on or off the headlights and taillights according to the signal.

DTC No.
DTC Detection Condition
Trouble Area
B1244
  1. Malfunction in automatic light control sensor.
  2. Open or short in automatic light control sensor circuit.
  1. Automatic light control sensor
  2. Main body ECU (Network gateway ECU)
  3. Harness or connector

WIRING DIAGRAM


E199045E07


INSPECTION PROCEDURE

1.READ VALUE USING GTS (ILLUMINATION RATE INFO)
  1. Connect the GTS to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the GTS on.

  1. Enter the following menus: Body Electrical / Main Body / Data List.

  1. Read the display on the GTS.

    Main Body 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Illumination Rate Info
    Illumination rate information / 0 ms to 99.99 ms
    Value is output according to ambient light levels
    -

    OK:
    Normal condition listed above is displayed.

    Result:
    Result
    Proceed to
    NG
    A
    OK
    B



B
REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)
A


2.CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (NETWORK GATEWAY ECU) - AUTOMATIC LIGHT CONTROL SENSOR)
  1. Disconnect the D6 main body ECU (network gateway ECU) connector.

  1. Disconnect the D45 automatic light control sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Open):
    Tester Connection
    Condition
    Specified Condition
    D6-13 (CLTE) - D45-6 (CLTE)
    Always
    Below 1 Ω
    D6-14 (CLTS) - D45-4 (CLTS)
    Always
    Below 1 Ω
    D6-15 (CLTB) - D45-3 (CLTB)
    Always
    Below 1 Ω

    Standard Resistance (Check for Short):
    Tester Connection
    Condition
    Specified Condition
    D6-13 (CLTE) - Body ground
    Always
    10 kΩ or higher
    D6-14 (CLTS) - Body ground
    Always
    10 kΩ or higher
    D6-15 (CLTB) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3.CHECK MAIN BODY ECU (NETWORK GATEWAY ECU)
  1. Reconnect the D6 main body ECU (network gateway ECU) connector.



    E247178E01
  1. Measure the voltage and resistance according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    D6-13 (CLTE) - D6-14 (CLTS)
    Ignition switch off
    Below 1 V
    Ignition switch ON
    11 to 14 V

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D6-13 (CLTE) - Body ground
    Always
    10 kΩ or higher

Text in Illustration 
*a
Component with harness connected
(Main Body ECU (Network Gateway ECU))


NG
REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)
OK


4.INSPECT AUTOMATIC LIGHT CONTROL SENSOR
  1. Reconnect the automatic light control sensor (Click here).

  1. Inspect the automatic light control sensor (Click here).



NG
REPLACE AUTOMATIC LIGHT CONTROL SENSOR (Click here)
OK

REPLACE MAIN BODY ECU (NETWORK GATEWAY ECU) (Click here)